Proposal to amend para. 5.3.3.2. to clarify that steering shall remain possible with performance laid down in para. 6. for the intact steering system in case of control transmission failure, amend para. 6.1.1. to specify that tests shall be conducted on a level surface affording good adhesion at ambient temperature between 0°C and 45°C, with provisions for deviating conditions at manufacturer request with Technical Service agreement, and insert new para. 6.2.5.1.1. to permit vehicle manufacturers to request at least 10 “figure of eight” manoeuvres with 40 m diameter loops at 10 km/h speed prior to measurement of steering efforts with steering equipment failure.

Proposal to modify the specified maximum remote controlled parking operating range from 6 m to 15 m. Large markets including Canada, USA, and China do not regulate maximum remote controlled parking operating range. Remote controlled parking systems exceeding 6 m operating range are already offered in the field. Radio wave-based ranging is inherently inaccurate due to complicated and varying electromagnetic environment in garage and changing orientation of remote device, requiring safety margin integration into product design, which reduces effective usable range below 6 m maximum. Extended range remote controlled parking systems have been used in the field for several years without negative feedback or identified safety threats.

Australia proposes to amend para. 2.14. to clarify that the nominal Peak Braking Coefficient value is understood to be the minimum value, and to amend para. 5.2.1.1. to simplify collision warning requirements for vehicles of category M₁. Industry objects the para. 2.14. amendment as unnecessary and potentially subject to misinterpretation as a requirement change. Industry agrees with dropping the 0.8-second prior warning requirement but finds the resulting text difficult to understand and proposes alternative wording that harmonizes para. 5.2.1.1. with paras. 5.2.2.1. and 5.2.3.1., specifying that a collision warning shall be provided no later than the start of emergency braking intervention.

In GRPE, discussions regarding control of aftermarket brake components with regard to brake particle emissions have prompted CLEPA’s desire to have access to type approval information to enable development of these components. Vehicle manufacturers make considerable investment in deriving these data and a supplier typically does not offer all affected brake components making a simple compliance test more difficult. OICA and CLEPA members are coming closer to an agreement regarding the necessary data, reducing the amount of data to be shared. A similar situation has been identified between UN R13H and UN R90.

The agenda includes GRVA decision to refer GRVA-2026-21 and GRVA-25-36 to the IWG on AEBS, proposals to amend UN R152 paragraphs 2.14, 5.2.1.1 and 5.2.1.2 per documents ECE/TRANS/WP.29/GRVA/2026/21 and GRVA-25-36, other business, action items and next meetings scheduled 24–25 September 2026 and 2–4 November 2026.

Proposal to insert provisions on software identification and software updates into UN R13, UN R13-H, UN R79, UN R89, UN R130, UN R131, UN R152, UN R156, UN R157, UN R171, UN R175, and UN R178 by adding definitions referencing Consolidated Resolution R.E.3 Annex 7, requiring manufacturers to provide Technical Services with information on hardware and software influencing performance, permitting vehicle manufacturers to apply for new approvals differentiating software versions for registered versus new vehicles, clarifying that production discontinuation does not apply when manufacturers seek approval extensions for software updates of registered vehicles, and amending communication forms to include software identification numbers and related information.

Research plan for ACPE vehicle performance. Tests using actual vehicles will evaluate ACPE performance of vehicles on the Japanese market. Tests specified in UN R175 01 series will be conducted, along with tests under extended conditions with partially expanded test parameters. Test procedure for creeping vehicle specified in UN R175 01 series, paragraph 6.6.2, will be conducted. Activation limits of ACPE will be confirmed using distance to target and pedal application speed as test parameters. Tests will use one 2026 model year Suzuki Swift and one 2026 model year Daihatsu Move. Vehicle procurement by end of September, testing late October to November, data analysis by end of December, summary of research results early January.

Proposal based on informal document GRVA-25-43 to amend Annex 4, para. 3.5.1. to require the manufacturer to demonstrate to the Type Approval Authority at least every three years that the safety management system continues to comply with requirements for software and hardware employed in the system. This amendment applies the same principle regarding Safety Management System compliance as specified in UN Regulation No. 171 on Driver Control Assistance Systems.

Proposal to insert para. 3.2.2. requiring manufacturers of Automated Lane Keeping Systems active in multiple Contracting Party territories to provide information on traffic rules identification, territory-specific testing, and contact details, insert paras. 4.8. to 4.8.6. establishing procedures for granting approval authorities to inform and consult receiving approval authorities at least 30 days before approval, allow receiving authorities 30 days to comment on regulation interpretation, require dispute resolution under Article 10 and Schedule 6 of the 1958 Agreement, and insert footnote [Y] stating these provisions shall be kept under periodic review by GRVA for amendment as necessary.

Proposal to amend para. 2.14. to insert a footnote clarifying that the road surface friction coefficient of 1 for sufficient nominal Peak Braking Coefficient (PBC) is understood to be a minimum value. This document is based on working document GRVA/2026/21 as amended by informal document GRVA-25-36.

Proposal to amend Annex 8, para. 3.4.1. to require that the strategy chosen shall not prejudice safe operation of the system due to failures with other systems involved in achieving the function of the system, and amend Annex 8, para. 3.4.4. to require that analysis of system behaviour on fault occurrence includes faults with other systems involved in achieving the function of the system, and to correct ‘safetys’ to ‘safety’. The proposal addresses a collision where tyre failure resulted in unsafe ABS activation. Although the 02 series clarified ABS as part of electronic control systems assessment, it does not explicitly state what is covered, potentially missing relevant faults or failures influencing system function. The additions ensure all relevant faults or failures are accounted for in manufacturers’ safety concept and analysis.

Proposal to insert a new sub-paragraph 5.6.1.1.4.1 to establish exemptions for Automatically Commanded Steering Function Category A functions designed for off-road low-speed vehicle recovery manoeuvres, and amend para. 5.6.1.2.7 to increase the specified maximum Remote-Control Parking operating range from 6 m to 15 m.

Proposal to amend para. 5.1.6.3.4. to specify that the intervention shall generate the signal to activate hazard warning lights and to clarify that for verification of timing requirements applicable to Risk Mitigation Functions, the signal to activate hazard warning lights is deemed to start the intervention, and amend Annex 8, para. 3.6.1.(b) to specify that the signal to activate hazard warning lights is generated at the earliest five seconds after the warning signal specified in para. 5.1.6.3.2. has been generated.

Proposal to improve the repeatability of tests and verifications, including:

• Insert a new para. 5.1.12. requiring that manufacturers provide information on the method by which the initiation signal of any system intervention required by the Regulation can be objectively identified and retrieved, including specific flags, status bits, or event codes on in-vehicle networks, and that manufacturers provide clear instructions and all necessary tools for the technical service to extract and interpret the signal, with the procedure for identifying the initiation of the system intervention and corresponding data appended to the test report.

Proposal to amend para. 2.8 of Annex 8 to add a new requirement that braking forces from combined service and parking braking systems shall hold a laden trailer as required in Annex 4 para. 3.2.1 at any time when service brake energy reservoir pressure reduces from 850 kPa to 0 kPa, ensuring continuous trailer immobilisation during service brake pressure depletion while establishing a performance-based requirement rather than prescribing specific technical solutions.

Proposal to insert provisions on Software Identification Numbers and software updates across UN R13, R13-H, R79, R89, R130, R131, R152, R155, R156, R157, R171, R175, and R178 by adding definitions referencing Consolidated Resolution R.E.3 Annex 7 paragraph 2, requiring manufacturers to provide Technical Services with information on hardware and software influencing performance with test reports, permitting vehicle manufacturers to apply for new approvals differentiating software versions for registered vehicles from new vehicles where type approval regulations are updated or hardware changes occur in series production with test duplication avoided where possible, clarifying that production is not considered definitively discontinued if manufacturers obtain subsequent extensions for software updates of registered vehicles, renumbering and inserting new items in approval communication annexes for R13SWIN, R13-HSWIN, R79SWIN, R89SWIN, R130SWIN, R131SWIN, R152SWIN, R155SWIN, R157SWIN, R171SWIN, R175SWIN, and R178SWIN information including whether held on vehicle and relevant parameter identification lists, and amending R157 and R171 to align software update requirements with R156 technical specifications and transitional provisions.

Proposal to amend Annex 3, paragraph 1.1.1. to delete the sub-paragraph referring to bedding of brake linings according to manufacturer’s instructions. A defined bedding procedure of brake linings was introduced in paragraph 1.1.2. of Annex 3 with Supplement 9 to the 01 series of amendments to UN Regulation No. 90. The last sub-paragraph of paragraph 1.1.1 had not been deleted in Revision 2 and 3 of UN Regulation No. 90, leading to different interpretations of the bedding procedure, which this proposal resolves.

Transport Canada presented ACPE research testing comparing three vehicles—2025 Tesla Model 3, 2025 Subaru Forester, and 2025 Toyota Crown Signia—against UN R175 minimum performance requirements and real-world pedal misapplication crashes. Analysis of 14 EDR data cases revealed none would require ACPE intervention under current R175 criteria. Testing included UN R175 procedures and recreation of six real-world crash scenarios. Proposed 2026 research includes investigating radar signatures of wall structures, obstacle distances exceeding 1.5 metres, accelerator pedal application rates and travel, and false positive test procedures.

Session report of WP.29 (World Forum for Harmonization of Vehicle Regulations), its Administrative Committee of the 1958 Agreement (AC.1), Executive Committee of the 1998 Agreement (AC.3), and Administrative Committee of the 1997 Agreement (AC.4) held 23-26 June 2026 in Geneva. AC.1 voted on 92 amendments to existing UN Regulations, one corrigendum to UN Regulation No. 79, and three new UN Regulations (Nos. 184-186) on liquid hydrogen vehicle safety, automated driving systems, and tyre abrasion performance. AC.3 established UN GTR on automated driving systems and adopted corrigendum to UN GTR No. 9 and Amendment 2 to UN GTR No. 13. WP.29 extended mandates of several informal working groups and noted accession of Mongolia and Armenia to the 1958 and 1997 Agreements respectively.

Proposal to establish a new UN Regulation transposing UN GTR No. 24 into uniform provisions concerning approval of non-original and identical replacement brake parts (brake pads, drum brake linings, brake discs, and brake drums) with regards to particle emissions. The regulation applies to vehicles of category M₁, N₁, and N₂ between 3.5 and 5 tonnes maximum mass. Replacement brake parts must comply with particle emission limits, with emission factors calculated using test wheel load and friction braking share coefficient for the brake emissions family parent. Approval marks must be affixed to approved parts, and conformity of production shall be verified through sampling and testing procedures.

GRVA held its twenty-fifth session on 23 June 2026 in Geneva, following consultations in Montreal from 18-22 June 2026. The working party endorsed status reports from informal working groups on Automated Driving Systems, cyber security and over-the-air updates, acceleration control for pedal error, advanced emergency braking systems, and event data recorder/data storage systems. GRVA adopted amendments to UN Regulations 79, 90, 152, 157, and 178, and amendments to documents on automated driving systems for submission to WP.29 and its administrative committees. GRVA established a task force on Exchange of Scenario-Relevant Information, extended the mandate of the Informal Working Group on Automated Driving Systems for three years, and agreed to pause activities of the Task Force on Advanced Driver Assistance Systems and install a task force for exchange on Automated Driving Systems implementation. GRVA noted various proposals on cyber security, data protection, connected vehicles, and advanced driver assistance systems for further consideration.

The Informal Working Group on Advanced Emergency Braking System held its 2nd meeting on 18 June 2026. Australia had submitted documents GRVA/2026/21 and GRVA-25-36 proposing amendments to UN R152. For para. 2.14, the group agreed to insert a footnote stating “this value is understood to be a minimum value,” with a working document to be prepared for next GRVA. For para. 5.2.1.1, Australia withdrew its proposal to remove the 0.8s TTC warning condition after safety concerns were raised. CLEPA-OICA, UK and Australia will prepare a clarification proposal for next GRVA.

Proposal to insert new para. 3.2.2. requiring manufacturers of Automated Lane Keeping Systems active in multiple Contracting Parties to provide information on traffic rules identification, territory-specific testing, and contact details, insert new paras. 4.8. to 4.8.6. establishing procedures for multi-territory approvals including notification of receiving approval authorities within 30 days, review and dispute resolution processes, and extension requirements, insert footnote [X] specifying communication via UNECE online platform or ECE/TRANS/WP.29/343 document, and insert footnote [Y] noting periodic review by GRVA.

Proposal to amend GRVA/2026/26, based on GRVA-25-18, insert new para. 3.2.2. requiring manufacturers of Automated Lane Keeping Systems active in multiple Contracting Parties to provide summaries of how traffic rules were identified and assessed, specific testing carried out, and a single point of contact, insert new paras. 4.8. to 4.8.6. establishing approval procedures requiring the granting approval authority to inform receiving approval authorities at least 30 days before approval with manufacturer information and safety statements, permit receiving authorities 30 days to provide comments, require disputes to be settled under the 1958 Agreement, and apply these requirements mutatis mutandis to extension approvals, and insert footnotes [Y] and [X] providing for periodic review and specifying contact methods via WP.29/343 online platform or document.

Proposed changes to align RxSWIN provisions with the RxSWIN template adopted through WP.29-197-06, remove the proposed requirement to comply with UN R156/01 or later from R157 and R171, remove amendments to UN R155 as decided by the IWG CS/OTA, apply the RxSWIN amendments also to earlier series of amendments in R13, R13-H, R79, R131, R152, R157, and R171, update references to the latest version of R.E.3, ECE/TRANS/WP.29/78/Rev.8, in earlier series, and correct paragraph references and improve structure in R89, R139, R140, R155, R156, and R171.