Proposal to insert a new para. 0 introducing supplements 4 and 5 to the 04 series of amendments extending the Regulation to vehicles of categories X and Y, amend para. 1 to modify scope provisions and add R-point clarifications for category X vehicles, amend para. 2.8 to revise the bonnet rear reference line definition including provisions for category Y vehicles without windscreens, amend para. 2.22 to clarify front structure definition for categories X and Y, amend para. 2.29 to specify occupant mass placement for categories X and Y, amend para. 2.32 to define side reference line for category Y vehicles, amend para. 2.44 to redefine windscreen test area for category Y vehicles, and amend para. 2.45 to adjust cowl monitoring area for category Y vehicles.

TF-AVRS submitted its status report to GRSP-79, advancing work on draft new Y-category Passive Safety Regulation and amendments to UN R127 for Y-category vehicles. The draft regulation addresses fuel system integrity, electrical shock protection, and crash compatibility based on UN R94, R95, R137, and R153. Horizontal items included eliminating R point problems, passenger compartment references, and A and B pillar designations, with harmonised mass definitions and consolidated numbering. Targets for 2026 included reviewing AVRS-adopted documents, correcting three regulations, and consistency checks across ADS amendments for WP.29-199.

The 25th session of the GRSP Task Force on Automated Vehicles Regulatory Screening (AVRS) was held online on 28 April 2026. The Task Force discussed regulatory frameworks for Y-category vehicles, including mass compatibility and crash test exceptions, and reviewed UN Regulation 127 on pedestrian protection for Y-category vehicles. The Task Force also addressed UN Regulation 12 feedback and identified minor mistakes in three proposals: ECE/TRANS/WP.29/2026/63, ECE/TRANS/WP.29/2026/65, and ECE/TRANS/WP.29/2026/71, which require corrections before submission to WP.29.

TF-AVRS submitted a draft new Y-category Passive Safety Regulation to GRSP-79 in June 2026. The regulation addresses fuel system integrity, electrical shock protection, and crash compatibility for frontal, rear-end, and lateral collisions. The Task Force eliminated the R point problem, passenger compartment references, and A and B pillar designations, harmonised mass definitions, and consolidated numbering and cross-references. Open items include determining additional requirements, specific vehicle measurements, and finalising Annex elements. Subsequent informal documents are planned for GRSP-79, with working documents for GRSP-80.

The 22nd session of the Task Force on Automated Vehicle Regulation Screening is scheduled for 20 May 2026 from 09:00 to 11:00 (CET) as an online meeting. The agenda includes welcome and opening remarks, adoption of the agenda and report of the 21st session, feedback and remarks from WP.29 expert groups on regulatory fitness for automated driving systems, determination of next meeting(s), and adjournment.

UN R127 amendment proposals include defining pedestrian protection requirements for category Y vehicles. Scope exemptions for category Y vehicles shall use front structural geometry to determine exemptions, ensuring equivalence to R-point criteria. Definitions require adjustments including Bonnet Rear Reference Line for vehicles without windscreens, Front structure definition to include automated driving sensors, Windscreen test area redefined as Upper structure test area where windscreens are non-existent, and supporting definitions for Side reference line and Cowl monitoring area. Testing shall occur at Unladen Vehicle Mass.

Proposal to insert a new para. 0 introducing amendments for vehicles equipped with an Automated Driving System, amend para. 1 to apply the Regulation to vehicles of categories M₁ and N₁ with specified exemptions and provisions for categories X and Y, amend the footnote to para. 1, amend para. 2.8 defining bonnet rear reference line with extended procedures for vehicles of category Y, amend para. 2.22 to include automated driving sensors in front structure for categories X and Y, amend para. 2.27 regarding mass in running order, amend para. 2.29 on normal ride attitude for categories X and Y, amend para. 2.32 on side reference line for category Y, amend para. 2.44 on windscreen test area for category Y without windscreen, amend para. 2.45 on cowl monitoring area, and amend para. 5.3.1.2 on Adaptive Ride Height Suspension engagement at low speeds.

Task Force FADS status report to GRVA presents final fitness information for GRVA Regulations relevant for automated vehicles. R157 (ALKS), R171 (DCAS), R178 (ELKS), R13, R13-H, R79, R89, R90, R130, R131, R139, R140, and R152 have been amended or are receiving amendments to clarify interactions with ADS features or account for vehicles of categories X and Y. R175, GTR3, and GTR8 require no amendments or formal amendment sponsorship. GRVA proposals for 13 working documents are expected at the 199th WP.29 session in June 2026, including WP.29/2026/85, WP.29/2026/86, WP.29/2026/87, WP.29/2026/79, WP.29/2026/80, WP.29/2026/81, WP.29/2026/82, WP.29/2026/83, WP.29/2026/168, and WP.29/2026/84. Task Force FADS mandate will conclude at the end of June 2026.

GRBP, GRE, GRPE, GRSG, GRSP, and GRVA are ready with working documents on non-ADS regulation amendments. TF AVRS is working on ADS marker lamps. UNECE published 93 amendment proposals regarding ADS fitness and ADS UNR and GTR for the 199th session of WP.29 in June 2026. UN R168.00 is tabled for the 200th session of WP.29. UN R154 former series is postponed to GRPE-95 in October 2026. Y category passive safety regulation is planned for GRSP-80 in December 2026.

The 26th meeting of GRSP TF on AVRS is scheduled for Tuesday 22nd of May 2026 as an online meeting from 09:00 to 11:00 CEST. The agenda includes approval of the agenda and minutes, feedback from other meetings, consistency check of GRSP ADS fitness work, Y-category regulatory framework for N₁, Y-category pedestrian protection under UN R127, feedback on passive safety requirements for new steering equipment types, any other business, and dates for next meetings.

UN R13 and UN R78 establish different brake system requirements for 4-wheel vehicles. R13H requires split service brake systems with front/rear proportioning; R78 permits split service brake systems, combined brake systems, or two separate service brake systems without proportioning requirements. Type-O dry braking tests differ: R13H requires engine disconnected at 100 km/h with stopping distance 0.1v + 0.0060 v² and MFDD 6.43 m/s²; R78 specifies multiple tests at 40, 60, and 100 km/h with varying requirements. Type-I brake fade tests use different snub protocols and performance thresholds. Secondary braking failure criteria differ at specified speeds. R78 requires wet brake testing, a 30 km/h dynamic park brake test with 18% gradient and 5 minutes hold time; R13H specifies static gradient tests. R78 includes detailed ABS, functional safety, and regenerative braking requirements; R13H does not.

Proposal to account for vehicles of category X and to extend its application to vehicles without driver and manual driving controls. New sections introduce definitions for Automated Driving System features (ADSF-1 and ADSF-2) and establish requirements for door closure warning systems and locking devices for vehicles equipped with ADSF-2. Vehicles of category Y are excluded from scope. Various paragraphs are amended regarding door systems, locking mechanisms, and impact definitions to address automated driving scenarios.

Corrections to proposals WP.29/2026/63, WP.29/2026/65, and WP.29/2026/71.

Results of the review of proposals for UN Regulations R28, R51, R64, R138, R141, R142, and R165 regarding autonomous vehicle readiness. Key findings include: inconsistent Mass in Running Order definitions between R51 and R138 versus RE3; unclear special testing provisions in R64, R138, and R165; need for clarification on ADS optical and logical signal transition in R64; redundant full definitions from RE3 in multiple proposals should reference RE3 via footnote instead; inconsistent ADS activity terminology across R64, R141, and R165 should be standardized; incorrect Category Y references in R51 Table 2; and definition and spelling errors in R51, R138, R141, and R165.

Proposal to amend UN R86 to address Automated Driving Systems:

• Insert new paragraphs 0, 0.1 to 0.1.2 introducing Supplement 3 to address vehicles of categories X and Y and conventional vehicles equipped with an Automated Driving System (ADS)
• Amend paragraph 1.1 footnote 1 to reference ECE/TRANS/WP.29/78/Rev.8
• Amend paragraph 1.3 subparagraph (a) to include control by an ADS
• Insert new paragraph 2.9.4 defining “Presence of an ADS”
• Amend paragraph 2.12 to expand immunity related functions to include ADS-related functions and functions related to charging mode when coupled to the power grid
• Delete paragraphs 2.26 and 2.27
• Renumber paragraphs 2.28 to 2.33 as 2.26 to 2.31
• Insert new paragraph 2.32 defining “ADS test configuration”
• Renumber paragraph 2.34 as 2.33
• Insert new paragraph 3.1.9 requiring specification of seating position if driver’s seat is not the front seat nearest to opposing traffic
• Insert new paragraph 6.11 and subparagraphs 6.11.1 to 6.11.3 establishing special requirements for ADS-equipped vehicles including alternative test methods and ESA immunity testing
• Amend paragraph 9.3.2 to reference ADS degradation in conformity verification
• Amend Appendix 8 paragraph 2 figures 3, 4, 5 and paragraph 3 figure 6 to correct charging notation from “>” to “<” and adjust time from 60 to 20 seconds
• Add new items 74 and 75 to Annex 2A addressing ADS presence and description
• Insert new paragraph 7 to Annex 3A Appendix and renumber former paragraph 7 as 8
• Amend Annex 4 paragraph 2.1.2 to reference ADS capability to switch equipment
• Amend Annex 5 paragraph 2.3 to reference ADS
• Amend Annex 6 paragraph 2.1.1.2 to establish “50 km/h mode”, “Brake mode” and “Active ADS Mode” test conditions with corresponding failure criteria including ADS operational state requirements
• Amend paragraph 2.1.1.3 to reference ADS
• Amend paragraph 2.1.1.4 to reference ADS features control
• Delete paragraph 2.1.1.5
• Amend paragraph 2.1.2 to permit manufacturer evidence for systems not operating under specified conditions
• Amend paragraph 2.2.1.3 to reference ADS for equipment switched OFF

UN R21 requires the owner’s manual to contain clear instructions for power-operated window/roof panel/partition systems, including explanation of possible consequences, use of driver-controlled switches, and WARNING messages indicating dangers to children and requiring special care with remote closing systems. UN R173 references to Annex 9, paragraph 3 are unnecessary as this paragraph no longer exists in R173 but is now in UN R16 S10 Annex. UN R94 Annex 3 requires a line break.

The 24th meeting of the GRSP Task Force on Automated Vehicle Regulatory Scheme (AVRS) was held on 2 April 2026. The agenda and previous minutes were approved. GRPE Regulation 154 is delayed; GRSG is progressing well. An AVRS Expert meeting on harmonizing terminology was held jointly with other groups. The EC screened GRBP AVRS documents; GEE screening is next. The TF discussed Y-category regulatory framework changes, including fuel leakage requirements, mass definitions, and cargo terminology. UN Regulation 127 for pedestrian protection will be updated for N₁Y categories. Discussions addressed T0 synchronization discrepancies in UN Reg 17 Annex 14 and FR comments on UN R12 ADS amendments. The next meeting is 28 April 2026.

Proposal to amend paragraph 1.1., footnote 1 to update the reference to the Consolidated Resolution on the Construction of Vehicles (R.E.3.); amend paragraph 4.4.1. to establish requirements for a dual-fuel operating mode indicator including visual and audio signals, with restrictions on indicator design and safety alert priority; amend paragraph 4.4.1.1. to require warnings when engine operation is forced to diesel mode and signals to an ADS feature; and amend paragraph 7.1. to specify OBD system requirements for diesel and dual-fuel operation modes, including malfunction detection and driver notification procedures.

Proposal to enable the approval of vehicles equipped with an Automated Driving System and to optimize the measurement accuracy requirements for chassis dynamometer equipment and the measurement acquisition of the intake manifold pressure in system power testing for high-performance vehicles and makes editorial corrections.

Proposal to insert new paras. 0, 0.1 to 0.1.3, amend paras. 1, 5, 6, 6.17.2.1, 16, 17, 17.1.7.1, 17.8.8, 17.8.8.1, 17.10.2, 17.11.4, and 17.13.2.3, insert new para. 14.1.4, and amend Annex 14 para. 6 to address vehicles of categories X and Y and conventional vehicles equipped with an Automated Driving System, extend application to vehicles without driver compartment and manual driving controls, clarify occupant compartment provisions, update electrical connection protection standards, and modify fault indication requirements to include logic signals to ADS and limp home mode activation.

Proposal to insert new paragraphs 0., 0.2. to 0.2.2. to introduce Supplement 1 to the 02 series of amendments taking into account vehicles of categories X and Y and vehicles with a manual mode operating at speeds above 6 km/h equipped with an Automated Driving System, amend footnote 1 to paragraph 1. to reference the Consolidated Resolution on the Construction of Vehicles (R.E.3.), document ECE/TRANS/WP.29/78/Rev. 8, and amend footnote 2 to paragraph 5.3.4.1. to reference Annex 3 to that document.

Proposal to:

• Insert new paragraphs 0. and 0.1. to 0.1.4. providing introduction to the 01 series of amendments regarding vehicles of categories X and Y and alignment of provisions for all occupants,
• Amend paragraphs 0.1., 0.1.1., 0.1.3., 1.1. and 2.2., footnote 1 to define terms according to Consolidated Resolution R.E.3.,
• Amend paragraph 2.7. to define passenger compartment,
• Amend paragraph 4.4., footnote 2 to reference Consolidated Resolution R.E.3.,
• Amend paragraph 5.2.1. to require heating systems in each passenger compartment,
• Insert new paragraphs 12. and 12.1. to 12.2.4. providing transitional provisions,
• Amend Annex 5, paragraph 2. to establish surface temperature requirements and allow manufacturers to justify higher temperatures through safety concept demonstration,
• Amend Annex 5, paragraph 2.1. to limit surface temperature to 70°C for uncoated metal or 80°C for other materials,
• Delete Annex 5, paragraphs 2.2. and 2.3.,
• As from official entry into force, Contracting Parties shall not refuse type approvals under the 01 series,
• As from 1 September 2028, Contracting Parties shall not be obliged to accept approvals to the original version first issued after that date,
• Contracting Parties shall continue accepting original version approvals first issued before 1 September 2028 and equipment/parts approvals issued under the original version.