Text proposing to clarify the current transitional provisions of UN Regulation No. 107. The proposal aims to ensure the validity of the preceding series of amendments to UN R107 for vehicles not impacted by the 05 series (mandating temperature alarm systems in certain bus compartments not directly visible to bus occupants).

Proposal to clarify the text of the amendments updating provisions for service doors, windows and emergency exits. The main purpose of the proposal is to delete the prohibition on the use of laminated glass or plastic material in window panes and to delete the provision that emergency windows shall be capable of being operated from outside.

Proposal to introduce the automatic activation of the hazard warning lights upon detection of excess temperatures in the engine and/or heater compartment.

Proposal to clarify that “low-floor vehicles” concern only those vehicles that provide a single step from the ground into the low floor area and that any equipment that would counteract the intention of such single-step low-floor vehicles to facilitate access by passengers with reduced mobility is prohibited.

Proposal to amend the requirements for fire prevention under certain conditions in the event of a rear collision. This document supersedes the earlier proposal contained in document GRSG/2013/4.

Proposal to adapt the provisions for multi-function displays to technological progress. In principle, current displays can convey more information to the driver, including levels of severity or importance, while the current text was written when technologies were less flexible. As a result, the current provisions risk impeding the use of beneficial multi-function tell-tales. This text is based on informal document GRSG-105-21.

Proposal to introduce, for special cases, adjustments to the coordinates of the ocular points used to check compliance with the required field of vision provided by the rear-view mirrors.. The proposal would align the definition of the “driver’s ocular points” with that of Regulation No. 125 (forward vision) as also used in EC Directive 2003/97/EC as amended by Directive 2005/27/EC. This document is based on informal document GRSG-105-19.

Text prepared to introduce provision to address difficulties encountered by technical services located at high altitudes in fulfilling the barometric pressure conditions required for the impact test. This document supersedes informal document GRSG-105-24.

Updated proposal to insert provisions in Annex 3 to facilitate access to a roof escape hatch in the event that the vehicle is lying on its side, superseding document GRSG-105-05 which superseded the original proposal in document GRSG/2013/17.

Text prepared by the Informal Group on the Introduction of Plastic Glazing for windscreens and laminated plastic panes other than windscreens into UN Regulation No. 43 (IGPG) in order to clarify the requirements of Annex 21 (provisions on the installation of safety glazing on vehicles).

Proposal to introduce more stringent requirements for rear underrun protection devices.

Proposal to require automatic mirrors to unfold automatically when the vehicle reaches a speed higher than 10 km/h. The concern is to address certain mirrors designed not to unfold at speeds up to 45 km/h.

Proposal to amend Annex 12 of the regulation to align its safety prescriptions for trolley buses with current electrical standards.

Proposal to avoid imposing administrative burdens on small glazing that is not required for the driver’s forward or rearward field of vision.

Proposal to extend the scope of UN Regulation No. 118 to vehicles powered by compressed natural gas (CNG).

Alternative from OICA to the proposal offered by Germany (document GRSG/2013/27 which is expected to be updated and presented as GRSG/2014/18) to introduce more stringent requirements for rear underrun protection devices.

Proposal to clarify the testing method for resistance to high temperature in order to address issues raised with testing at high altitudes. CLEPA proposes to amend the wording of paragraph 5.1. to clarify how to proceed with a test in boiling water, which is permitted for safety glazing with both external surfaces of inorganic material. The tolerance of +0 °C / -2 °C is taken from ISO 3917, high temperature test. The temperature of boiling water can be determined with the required accuracy easily.

Proposal to introduce fire suppression systems for buses and coaches upon detection of fire in the engine and/or heater compartment.

Proposal to introduce provisions for the use of plastic safety glazing in side windows behind the B pillar more in line with the stipulations for glazing with a light transmittance below 70 per cent in that area.

Excerpt from the March 2014 session of the World Forum where Korea explained its investigation into the shattering of certain panoramic sunroofs.

Proposed mandate for the expert group working on regulatory provisions for in-vehicle automated accident emergency call devices.

CLEPA comments on the OICA proposal for Supplement 3 to the 01 series of amendments to Regulation No. 43 (document GRSG/2014/14) that seeks to avoid imposing administrative burdens on small glazing that is not required for the driver’s forward or rearward field of vision.

Proposal to align the text of UN R105 with that adopted by the Working Party on the Transport of Dangerous Goods (WP.15) on the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR), edition 2015.

Proposal to include odometers within the scope of Regulation No. 39 (as an alternative to the proposal in document GRSG-104-14 to develop a new regulation on the installation and performance of odometers).

Proposal to regulate the discharge direction of pressure relief devices (PRD) on CNG containers in response to a fire accident in the Netherlands in which the PRD produced a long horizontal jet flame for several minutes posing a risk to other road users and surrounding buildings.

Russian comments and proposals to modify the proposal to amend Annex 12 of the regulation to align its safety prescriptions for trolley buses with current electrical standards.

Proposal to clarify that an “overnight locking system” referred to in the proposed amendment to paragraph 2.41 is not one intended to be operated by passengers from inside the vehicle.

Proposal to replace in paragraph 6.2.6. of UN Regulation No. 118, the obsolete reference to the cable test according to paragraph 12. of ISO 6722 with the correct reference to paragraph 5.22. of ISO 6722-1:2011.

Proposal to modify document GRSG/2014/5 which would amend the current transitional provisions of UN Regulation No. 107in order to ensure the validity of the preceding series of amendments to UN R107 for vehicles not impacted by the 05 series (mandating temperature alarm systems in certain bus compartments not directly visible to bus occupants). This proposal would change the proposed language in order to clarify that vehicles not affected by the 05 Series of amendments can continue to be approved with no modification to their markings, and that extensions to the approvals for these vehicles can continue to be granted.

Proposal by the IGPG working group to introduce provisions for plastic glazing for windscreens and laminated plastic panes other than windscreens into UN Regulation No. 43, superseding document GRSG-104-43.

Note to open a discussion concerning the gas-cylinder periodic inspection requirements of Annex 3 of UN R110.

As part of a broad project to identify possible incoherences across definitions of terms used in UN Regulations, the secretariat has prepared this list of definitions under the responsibility of GRSG.

In document GRSG/2013/29, the AEGPL proposed to introduce new provisions into Regulation No. 67 for preventing the flow of liquefied petroleum gas (LPG) into the petrol or diesel tank, and vice versa in order to address a potential safety risk in bi-fuel or dual-fuel vehicles. At the 105th GRSG session, Germany requested a more detailed test procedure. Therefore, this proposal responds to the German request, improves certain descriptions of requirements, and provides comments to justify the various provisions.

Proposal to amend the methodology of the 227g ball drop test for toughened glass in order to assess its mechanical strength (resistance against outside impact). This proposal stems from Korean testing that demonstrated inadequate mechanical strength of toughened glass treated with ceramic printing.

Proposal to clarify restrictions on the application of an RUPS according to specific vehicle chassis characteristics (e.g., stiffness, profile dimensions) under Annex 1 (item 9) the test set-up Annex 1 item 9 and to adapt the test procedure of Annex 5 (paragraph 1.1.3.) accordingly by the use of representative side rails. The proposal would also specify that the device used to distribute the test force over the stated flat surface be connected to the force actuator through a swivel joint since a wholly rigid set up can result in very different and unintended outcomes.

Corrections and clarifications by Japan to its earlier submission concerning the requirements for fire prevention under certain conditions in the event of a rear collision (Proposal for the 03 series of amendments to Regulation No. 34 ).

Presentation on Korean investigations that identify certain conditions under which ceramic printing (black enamel) weakens toughened glass such that the glass no longer meets the mechanical strength requirements of GTR 6, UN R43 or FMVSS 205. Korea proposes amending the UN glazing regulations.

Proposal to align Annex 11 of UN R107 with Regulation (EU) 1230/2012. Annex 11 was originally based on EU Directive 97/27 EC (type approval of vehicles with regard to their masses and dimensions) which has now been replaced by Regulation (EU) 1230/2012, thus prompting the need for realignment.

Supplement 1 to the 01 series included requirements for the positioning of LNG tanks. While the Netherlands believes that mounting the LNG fuel tank 200mm above the road surface is broadly adequate; this proposal aims to ensure that the fuel tank cannot, under any normal driving or stationary working situations, come into contact with the ground. The new wording provides more definitive conditions, including the possibility of a vehicle having one or more flat tires as well as for those vehicles that have ‘kneeling’ capability or variable suspension, both of which lower the frame of the vehicle closer to the ground.

Proposal to require, in configurations where the engine compartment is located to the rear of the driver’s compartment, that the engine cannot be started from the driver’s position when the panel giving access to moving parts of the engine is open. It takes into account the comments received during the 105th session and supersedes documents GRSG/2013/14 and GRSG-105-14.

Proposal to add field-of-vision provisions to enhance the safety of pedestrians and other vulnerable road users in narrow alleys and by-streets and other improvements to UN R46. This document replaces documents GRSG/2013/5 and its Corrigendum 1.

Text prepared by the GRSG secretariat pursuant to GRSG discussions on the proposal for a supplement to UN R107 to align the provisions of Annex 12 (concerning trolley buses) with current electrical standards.

Proposal to require an exterior protection on cylindrical gas tanks. Under the current regulation, such exterior protection may be fitted at the discretion of the manufacturer. The intention is to increase protection against corrosion of cylinders in response to a corroded cylinder explosion in Germany.

Editorial changes to the proposal to introduce more stringent requirements for rear underrun protection devices (document GRSG/2014/18).

Presentation highlighting concerns regarding the separate development of UN R110 and ISO 11439 provisions resulting in diverging test protocols and other differences.

This proposal corrects an editorial mistake in the tolerances of Annex 6. In Annex 10, paragraph 3.2.2.2. and in Annex 12, paragraph 3.2.2., the correct tolerance should read: 1.5m +0/-5mm. (The same tolerances also appear in UN GTR No. 6, paragraphs 5.4.3. and 6.5.4.2.)

Comparison of the OICA and German proposals to set new requirements for rear under-run protection devices.

Presentation in support of Japan’s proposal to increase the stringency of UN R34.

Proposal to add classifications covering agricultural trailers and towed agricultural machinery in the Consolidated Resolution on the Construction of Vehicles (R.E.3).

Updated version of the text prepared by the GRSG secretariat pursuant to GRSG discussions on the proposal for a supplement to UN R107 to align the provisions of Annex 12 (concerning trolley buses) with current electrical standards.

Adopted version of the proposal by Japan (GRSG/2014/16) to amend provisions for testing of fire risks in rear-end collisions as amended during the May 2014 GRSG session.

European Commission request for input on the possible type approval of new systems that enable unlocking cars via smart phones and that send silent alarms to security services via the Internet.

Presentation in support of the development of technical regulatory specifications to prevent odometer tampering.

Presentation in support of the proposal to include odometer provisions in UN R39, including a review of references to odometers across other UN Regulations.

Presentation concerning the asynchronous use of an indicator space for communicating information to the driver. The presentation explains the concept of this “common space” that two or more symbols may share but only use one at a time. The presentation proposes that two or more symbols might be displayed sequentially in the same common space (i.e., alternately flashing symbols).

Revised proposal to add classifications covering agricultural trailers and towed agricultural machinery in the Consolidated Resolution on the Construction of Vehicles (R.E.3).

Query concerning the intent of the proposed changes to the test procedures for rear underrun protection devices (RUPD). Sweden believes that the wording of the amendments proposed in document GRSG/2014/18 would change the nature of RUPD from being generic devices for installation across ranges of vehicle types to being vehicle-specific devices requiring repetitive testing for approval to be installed on a range of vehicles. Therefore, Sweden raises the question of whether this is the intent of the German proposal.

Proposal to regulate the direction of discharging the pressure relief devices of CNG containers.

Proposal to clarify the provisions for the periodic inspection of pressure relief valves.

Proposal to introduce a new class of CNG components (Class 6) operating at a higher pressure.

Proposal to update the reference to ISO 6722 in the cable test (i.e. replace the reference to IS0 6722 paragraph 12 with a reference to ISO 6722-1:2011 paragraph 5.22).

Proposal to add classifications covering agricultural trailers and towed agricultural machinery in the Consolidated Resolution on the Construction of Vehicles (R.E.3).

Proposal to include odometers within the scope of Regulation No. 39.

The newly introduced systems to detect excessive temperatures and/or smoke enable the driver to act immediately to ensure the safety of the passengers. This implies the possibility of braking, stopping, or some other response which could impact other road users. Therefore, this proposal would require the hazard warning lights to be activated (which will require consideration by the WP.29 Working Party on Lighting and Light-signalling Equipment). The proposal also proposes transitional provisions for the implementation of the new requirements.

Text prepared by the Netherlands and the International Association for Natural Gas Vehicles (IANGV/NGV Global) to clarify the provisions of Chapter 18 following the introduction of automatic valves (see report GRSG/84, para. 38).

Annotated provisional agenda for the Fall 2014 session of the Working Party on General Safety.

Text prepared by Germany on behalf of the Informal Group on Plastic Glazing (IGPG) to introduce new provisions for windscreens and for laminated plastic panes other than windscreens.

Proposal to align Annex 11 of UN R107 with Regulation (EU) 1230/2012. Annex 11 was originally based on EU Directive 97/27 EC (type approval of vehicles with regard to their masses and dimensions) which has now been replaced by Regulation (EU) 1230/2012, thus prompting the need for realignment.

Proposal to add field-of-vision provisions to enhance the safety of pedestrians and other vulnerable road users in narrow alleys and by-streets and other improvements to UN R46.

Proposal to establish an expert working group to review and update the provisions of UN Regulation No. 110 in order to produce a new consolidated, harmonized version of the regulation.

In document GRSG/2014/22, the EC proposes to align Annex 11 of UN R107 with Regulation (EU) 1230/2012 (type approval of vehicles with regard to their masses and dimensions). However, the volume and location of masses – including baggage masses – impacts many basic parameters of buses like total mass in running order, axle loads, CG position, etc. and related UN Regulations. This document raises issues for consideration during the review of the EC proposal.

In document GRSG/2014/4, Hungary proposed to delete the provision that emergency windows shall be capable of being operated from outside the vehicle. This document provides a written justification for the proposal to enable its formal approval by GRSG.

Proposal to amend the test methods for toughened glass pursuant to Korean defect investigations involving the ceramic printed area of certain panoramic sunroofs.

European Commission proposal to revise the proposal of the GRE Informal Group on Agricultural Vehicle Lighting Installation (AVLI) to add new vehicle categories in the Consolidation Resolution on the Construction of Vehicles to cover agricultural trailers and towed machinery. The EC aims to bring the proposal and Regulation (EU) 167/2013 into alignment.

Input from Germany in response to the European Commission request (document GRSG-106-38) for input on the possible type approval of new systems that enable unlocking cars via smart phones and that send silent alarms to security services via the Internet.

Pursuant to research conducted in Japan, this document recommends amending UN R110 with regard to:

1. Welded metal cylinders
2. Steel cylinders (CNG-1 cylinder) and Steel liner cylinders (CNG-2 cylinder)
3. Accessories fitted to the cylinder, and
4. Indication of cylinder and accessories fitted to the cylinder.

The document also raises the possibility of further considerations concerning LNG cylinders.

Proposal by Germany to amend the Swedish proposal (document GRSG/2014/6) to introduce approval provisions for automatic fire suppression systems activated upon the detection of fire in the engine and/or heater compartment of buses and coaches. This proposal would limit mandatory installation to Class III vehicles.

Explanations and arguments in support of the amendments to UN R43 proposed by the Informal Group on Plastic Glazing (IGPG) in document GRSG/2014/23.

UN R116 specifies operating voltages and voltage limits. Current technology and intelligent battery management systems allow for precise control and definition of these parameters. This includes “intelligent” operating ranges in order to optimize energy management (CO2 emission reduction). Fixed operating voltage ranges are therefore unnecessary or even may hinder efforts for CO2 emission reduction in the future. OICA proposes language to modify the design-restrictive language.

OICA comments on the proposal to introduce fire suppression systems for buses and coaches upon detection of fire in the engine and/or heater compartment (document GRSG/2014/6).

Proposal for an amendment to UN Regulation No. 43 to define a “reduced vision zone I” for vehicles of categories M and N other than M1. The goal is to extend the concept that already exists for M1 vehicles in order to enable the installation of sensors and cameras that improve driving safety.

Correction to clarify that the scope of the GTR covers windscreens and panes for cars and trucks and to harmonize the text with ISO 3537/ UN R43. The present text could be read to limit the scope of windscreens and double window panes.

OICA and CLEPA comments on the Korean proposal to amend GTR No. 6 and UN Regulation No. 43 in response to issues identified in its defect investigation concerning panoramic sunroofs.

This proposal aims to enable the use of thick glass panes for multiple glazed units which, in turn, requires omitting the head-form test in case of these units.

Proposal to modify the draft amendment to UN R39 that would introduce odometer requirements (document GRSG/2014/32). OICA proposes to change the definition of “odometer” to refer to the distance recorded rather than traveled and to delete the definition of “technical constant of the odometer”.

Proposal to correct the calculation of total mass under the draft 05 and 06 series amendments intended to align Annex 11 of UN R107 with Regulation (EU) 1230/2012 (i.e., the amendments proposed in document GRSG/2014/22).

More detailed explanation of the proposal (document GRSG/2014/24) to update the reference to ISO 6722 in the cable test (i.e. replace the reference to “IS0 6722 paragraph 12” with a reference to “ISO 6722-1:2011 paragraph 5.22”).

The draft 03 series of amendments follows current UN guidelines for regulatory texts (document WP29/1044/Rev.1); however, a new version of the guidelines which uses a different phrasing for transitional provisions will soon be adopted. Therefore, OICA proposes using the new wording in the draft 03 series.

Paragraph 5.3.1. refers to Appendix 8 of Annex 1. OICA believes that the reference should be to Appendix 10 of Annex 1 and so proposes this correction.

Amended proposal to include odometers within the scope of UN R39, deleting the reference to the “technical constant” and a provision for the installation of a replacement odometer.

This file is password-protected. ISO provided these standards "for the sole purpose of review during UNECE GRSG regulations development for GRSG participants, and not for public posting or reproduction without ISO’s permission.” Parties involved with this work may contact the GRSG secretariat to obtain the password.

ISO Standard 11439 concerns “High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles”. ISO 6722 concerns ’60 V and 600 V single-core cables — Part 1: Dimensions, test methods and requirements for copper conductor cables".

Proposal to introduce fire suppression systems for buses and coaches upon detection of fire in the engine and/or heater compartment, superseding document GRSG/2014/6.

Proposal to amend the draft 03 series of amendments to UN R58 (document GRSG/2014/18).

Proposal to exclude M1 vehicles from the close-proximity field of vision requirements pursuant to the establishment of the international whole vehicle type approval system.

Revised proposal to introduce more stringent requirements for rear underrun protection devices, amending and superseding document GRSG/2014/18.

Request to postpone consideration of the Dutch proposal concerning the discharge of natural gases from a pressure relief device (PRD) in anticipation of conclusions and best practices on the location and venting of PRD from a research program underway in the US.

Progress report from the group of experts working on provisions to enable the type approval of video systems in place of conventional rear-view mirrors.

Proposal to revise the text of document GRSG-107-25 on fire suppression systems to ensure that the provisions can be applied fully to natural gas and/or hydrogen-powered vehicles.

Comments in support of the proposal to introduce provisions for fire-suppression systems under UN R107.

Corrections to the proposal to clarify the provisions of Chapter 18 following the introduction of automatic valves (see report GRSG/84, para. 38).

Proposal to add a definition for “CNG Accumulator” and to revise a related decision tree flow chart.

Proposal to delete provisions regarding the optical display of the status of the vehicle alarm system outside the passenger compartment in order to avoid driver distraction by and/or confusion of such exterior lighting with primary lighting and signaling equipment required under UN R48.

Proposal to delete provisions regarding the optical display of the status of the vehicle alarm system outside the passenger compartment in order to avoid driver distraction by and/or confusion of such exterior lighting with primary lighting and signaling equipment required under UN R48.