Proposal by Italy, France and Laser Europe to rearrange the text of the Convention, including Chapter II of Annex 5.

Comments on the draft test procedures as described in the draft text of document ACSF-04-20.

Presentation on French government views on the approval of automated steering at speeds above 10 km/h under UN Regulation No. 79. The principle recommendation is to restrict amendments to UN R79 to lateral vehicle control as speeds above 10 km/h while setting other work on more advanced capabilities (longitudinal + latitudinal, lane change, passing, etc.) for future separate regulations.

Comments on the draft Supplement 5 to UN R28.

Copy of document GRRF-81-14: Presentation on French government views on the approval of automated steering at speeds above 10 km/h under UN Regulation No. 79. The principle recommendation is to restrict amendments to UN R79 to lateral vehicle control as speeds above 10 km/h while setting other work on more advanced capabilities (longitudinal + latitudinal, lane change, passing, etc.) for future separate regulations.

Proposal to prioritize work towards adopting “secure by design” standards for vehicle architecture and network systems, including attention to automotive safety integrity level (ASIL) methods proposed in ISO 26262.

Proposal to require seat-belt reminders for all seating positions, including rear positions, and to clarify the scope of the regulation.

Proposal from the CRS informal group to introduce phase 2 amendments regarding the approval of booster-seat CRS category (booster seat with backrest) into UN R129.

Proposal to enable the use of alternate colors (per footnote 18 of Table 1 and in line with ISO Standard 2575) for certain lighting tell-tales in order to indicate light source failures in response to the proposals for light failure indicators under UN Regulations Nos. 7, 48 and 87 (GRE/2016/7, GRE/2016/12 and GRE/2016/17) as adopted by GRE. This proposal anticipates use of the same approach in response to plans for additional failure indication requirements for other lighting regulations.

Proposal to allow for the use of natural gas refrigeration systems to vehicles propelled by natural gas (CNG or LNG). This proposal addresses a new, environmentally friendly natural gas fuelled refrigeration system for trucks with refrigerated loads that already are propelled by natural gas. Currently paragraph 18.1.7.1 allows heating systems to be fitted on vehicles to heat the passenger compartment and/or the load area of a vehicle, however, the same provision omits cooling systems that are used on trucks for the carriage of loads requiring refrigeration.

Proposal to introduce provisions for seat-belt reminders for all vehicle seating positions pursuant to the outcome of the Task Force on Seat-belt Reminders discussions.

Proposal to clarify paragraph 8.1.2. The paragraph aimed to verify that the compensator can accept a difference of the travel when one brake operates in forward direction and the other in rearward direction with a margin of twenty per cent.

Proposal to allow for the case of a tyre designed for a special application that also fulfills the requirements for a snow tyre such that the tyre, at the manufacturers initiative, shall be marked with the inscription M+S or M.S or M&S while remaining in the category of use “special use tyre”. The proposal further adds “test laboratories” in the headline of paragraph 12. as quoted in subparagraph 12.1. in document WP.29/2016/51 as adopted during the June WP.29 session with the aim of harmonizing the tyre regulations.

Proposal to:
a) Align some definitions and some contents of paragraphs with the other tyre regulations (Regulations Nos. 30, 54, 117, etc.);
b) Include a definition of “manufacturer” extracted from the resolution “R.E.3”;
c) Adopt a common definition and use of the terms “Manufacturer’s name”," Brand
name", “Trademark”, “Trade description” and “Commercial name” and their links;
d) Clarify the designation of the categories of use;
e) Remove the word “normal” in the definition of “Reinforced” tyre to avoid confusion
with the category of use “normal”;
f) Add some information in the certificate to the attention of the Type Approval
Authorities for making easier the relationship between this one and the products.

Proposal to introduce technical requirements for Corrective Steering Functions (lane departure prevention, lane-keeping assistance (LKAS), steering angle correction, etc.) as defined in the regulation. The proposal offers four options to ensure appropriate approvals of LKAS and related CSF systems until such time as more precise requirements can be defined:

• Option 1 and option 2: Not to grant any type approvals for corrective steering functions until detailed technical requirements for CSF are incorporated into this Regulation.
• Option 3: Amend the definition of CSF as proposed in this document.
• Option 4: Amend the definition of corrective steering functions and to include technical requirements for LKAS as an ASCF of Category B1 as proposed in this document.

Proposal to:
a) Align definitions and contents of paragraphs with the other tyre regulations (UN R30, R54, R117, etc.);
b) Include a definition of “Manufacturer” extracted from the resolution “R.E.3”;
c) Adopt a common definition and use of the terms “Manufacturer’s name”," Brand name", “Trademark”, “Trade description” and “Commercial name” and their links;
d) Clarify which markings shall be moulded on both sidewalls of the tyre; and those which shall be moulded on one sidewall only;
e) Add information in the certificate to clarify the relationship with the certified products;
f) Align definitions with Regulation EU 167/2013 which defines vehicles in category S as “interchangeable towed equipment” and includes tread patterns for ‘implement traction tyres’ that consist of blocks rather than lugs or cleats;
g) Eliminate redundant marking requirements;
h) Clarify the inflation pressure to be used for measurements and tests and related tyre markings;
i) Align the current rules for calculating the dimensional limits in accordance with ISO, all major tyre standards, and as proposed for UN R30, R54, and R75.

Proposal to reduce the administrative burden in obtaining approvals for electrical cables according to UN Regulation No. 118. The experts from Finland, France and Germany agreed that the change from ISO 6722:2006 to ISO 6722-2011 does not impact the degree of safety and, therefore, the test reports or approvals established under the older version of the ISO standard shall remain valid.

Proposal to improve and clarify provisions concerning the approval of interior materials, cables and insulation materials. The proposaladds new requirements for cable sleeves and conduits, modifies vertical testing requirements under Annex 8 to allow testing of small test samples and to clarify their fixation to the specimen holder., and adds a new Annex 10 on provisions for testing of electrical cables.

Proposal to allow for the use of natural gas refrigeration systems to vehicles propelled by natural gas (CNG or LNG). This proposal addresses a new, environmentally friendly natural gas fuelled refrigeration system for trucks with refrigerated loads that already are propelled by natural gas. Currently paragraph 18.1.7.1 allows heating systems to be fitted on vehicles to heat the passenger compartment and/or the load area of a vehicle, however, the same provision omits cooling systems that are used on trucks for the carriage of loads requiring refrigeration.

Proposal to amend the consolidated draft amendment to UN R79 to introduce technical requirements for Corrective Steering Functions and Level B1 ACSF under UN R79 (document GRRF/2016/45).

Proposal to align the provisions on toxicity and flammability of materials used to manufacture Child Restraint Systems (CRS) and to update test provisions of UN Regulation introduced by the Supplement 1 to the 01 series of amendments to UN Regulation No. 129. It is based on ECE/TRANS/WP.29/2016/106, adopted at fifty-ninth session of the Working Party on Passive Safety (GRSP) and modifies ECE/TRANS/WP.29/2016/107 (02 series of amendments to the UN Regulation).

Proposal to amend the draft text concerning sequential activation of direction indicators. The amendments aim to ensure reasonable uniformity across direction indicators in order to reduce the risk of misinterpretation by other road users. The modifications proposed by the France replace the terms “apparent surface” and “continuous” with specific objective criteria.

Proposal to add new CRS fixtures and otherwise align UN R16 with changes introduced through UN R129 (enhanced child restraint systems). Two “Booster Seat” fixtures (ISO/B2 and ISO/B3) were added to UN R16 to coincide with the implementation of Phase 2 of UN R129. These fixtures were developed within ISO/TC 22/SC 36/WG 2 (Child Restraint Systems) and follow the principle already established in Regulations 16 and 129 to ensure child restraint to car compatibility. An additional “Reduced-Size Rearward Facing toddler CRS” fixture (ISO/R2x) was added to facilitate compatibility in small cars/seating positions. The ISO/B2 booster seat fixture was added in the i-Size concept. Lateral facing fixtures (ISO/L1 and ISO/L2) have been upgraded.

Proposal to update the 07 series of amendments in line with UN R129 and changes to the 06 series (Supplements 8 and 9). Two “Booster Seat” fixtures (ISO/B2 and ISO/B3) were added to UN R16 to coincide with the implementation of Phase 2 of UN Regulation No. 129. These fixtures were developed within ISO/TC 22/SC 36/WG 2 (Child Restraint Systems) and follow the principle already established in Regulations 16 and 129 to ensure child restraint to car compatibility. An additional “Reduced-Size Rearward Facing toddler CRS” fixture (ISO/R2x) was added to facilitate compatibility in small cars/seating positions. The ISO/B2 booster seat fixture was added in the i-Size concept. Lateral facing fixtures (ISO/L1 and ISO/L2) have been upgraded.

Proposal from the CRS informal group to clarify requirements and improve the text of the 02 series of amendments, including strap positioning provisions and labeling requirements for detachable child seat impact shields.

Proposal from the CRS informal group to clarify and improve the text of the 01 series of amendments.

Proposal to align UN R14 with recent changes to UN R16 on occupant restraint systems. Two “Booster Seat” fixtures (ISO/B2 and ISO/B3) were added to UN R16 to coincide with the implementation of Phase 2 of UN R129 (enhanced child restraint systems). These fixtures were developed within ISO/TC 22/SC 36/WG 2 (Child Restraint Systems) and follow the principle already established in Regulations 16 and 129 to ensure child restraint to car compatibility. An additional “Reduced-Size Rearward Facing toddler CRS” fixture (ISO/R2x) was added to facilitate compatibility in small cars/seating positions. The ISO/B2 booster seat fixture was added in the i-Size concept. Lateral facing fixtures (ISO/L1 and ISO/L2) have been upgraded.

Consolidated version of UN R129 including the proposals for the 02 series of amendments (WP29/2016/107), Supplement 1 to the 02 series of amendments (GRSP/2016/19), and Supplement 2 to the 02 series of amendments (GRSP/2016/22). The 02 series concerns the “phase 2” amendments regarding the approval of booster-seat CRS category (booster seat with backrest). Supplement 1 updates the toxicity and flammability of materials provisions pursuant to Supplement 1 to the 01 series of amendments. Supplement 2 proposes editorial improvements and corrections to the original text.

This informal doc amends the draft supplement presented in document GRSP/2016/24 in order to harmonize the mass tolerances of the ISO fixtures. The proposal deletes a reference to the center of gravity and geometrical centroid. The centroid would need more information before choosing tolerances needed for certification tests.

This informal doc amends the draft supplement presented in document GRSP/2016/21 in order to harmonize the mass tolerances of the ISO fixtures. The proposal deletes a reference to the center of gravity and geometrical centroid. The centroid would need more information before choosing tolerances needed for certification tests.

Proposal to clarify and make editorial corrections to the text of the 02 series of amendments to the UN Regulation No. 129. This proposal supersedes document GRSP/2016/23 and amends WP.29/2016/107 (02 series of amendments to the UN Regulation) and GRSP/2016/19 (Proposal for Supplement 1 to the 02 series of amendments to Regulation No. 129).

Proposal to clarify and make editorial corrections to the text of the 02 series of amendments to the UN Regulation No. 129. This proposal supersedes document GRSP/2016/22 and amends WP.29/2016/106 (02 series of amendments to the UN Regulation).