Draft 01 series of amendments to Regulation No. 127 presented in a consolidated text of the regulation as adopted by GRSP and which aligns the test requirements of UN Regulation No. 127 with UN GTR No. 9 Phase 2 (Flex-PLI), incorporating Supplement 1 to the original version of the UN Regulation (determination of the headform test points).

Report of the Working Party on Passive Safety on its December 2013 session.

Working draft of the phase 2 revisions to the global technical regulation on head restraints provided to the GRSP at its December 2013 session for informational purposes only.

Draft version of the proposed UN Regulation that would transpose Global Technical Regulation No. 14 on pole side-impact protection into the type-approval system of the 1958 Agreement. This draft is presented for informational purposes only pending submission of a final document for consideration by the GRSP.

Working draft of the proposed amendments to introduce provisions for non-integral CRS (“Universal Booster” or “Specific to vehicle Booster”), incorporating all the changes agreed during the 54th (December 2013) GRSP session.

UN R17, R25 and R80 address head restraints for various categories of vehicles. In order to prevent redundant application of these regulations, this amendment clarifies that head restraints approved under UN R17 would be exempted from the requirements of UN R25 and that UN R25 does not apply to coach and bus seats approved under UN R80.

Proposal to clarify provisions on the headform tests of UN GTR No. 9.

Proposal to clarify provisions of the headform tests of UN GTR No. 9.

Amendment to introduce all the modifications needed in UN Regulation No. 129 (Enhanced Child Restraint System (ECRS)) that were suggested by the experts of the informal working group on Child Restraint Systems (IWG CRS) to extend the scope of this Regulation to Non-Integral child restraint systems (“Universal Booster” or “Specific to vehicle Booster”) (Phase 2 of the UN Regulation).

Draft text for a new UN regulation on the safety of electric motorcycles and related vehicles.

Draft text for the transposition of GTR No. 13 on hydrogen and fuel-cell vehicle safety into a new UN Regulation under the 1958 Agreement. Part 1 of Annex 1 uses the numbering system prepared for the corresponding annexes of the International Whole Vehicle Type Approval (IWVTA) regulation (UN R0) currently under development.

Draft text transposing GTR No. 14 on pole side impact protection into a UN Regulation under the 1958 Agreement. A proposal for the 01 series of amendments (document GRSP/2014/12) has also been prepared to enable the Contracting Parties applying this Regulation to require a vehicle-to-pole impact speed of 32 ±1 km/h regardless of the “vehicle width”.

Proposal for a 01 series of amendments to the proposed new UN Regulation on the approval of vehicles with regard to their pole side impact performance to enable Contracting Parties applying this new regulation to require a vehicle-to-pole impact speed of 32 ±1 km/h regardless of the “vehicle width”.

Certain anti-theft systems fully lock every door and window in a vehicle and also deactivate interior unlock controls. This can lead to a situation where an occupant can be locked inside a vehicle with no means of exit save to break a window. This proposal would introduce provisions for the safety and protection of road vehicle occupants in case of the installation of such a full locking system.

Text prepared by the Informal Working Group on Frontal Impact (IWG FI) as an outcome of discussions of the Working Party on Passive Safety (GRSP) at its fifty-fourth session (ECE/TRANS/WP29/GRSP/54, para. 23) on developing a separate new Regulation on frontal impact focusing on requirements for restraint systems.
.

In parallel with the introduction of a new Regulation on a frontal impact with focus on the restraint system, this proposal would limit the chest deflection of the Hybrid III dummy to 42 mm (from the current 50 mm) in order to promote improved protection of older occupants.

Proposal to require that the vehicle cab remain attached to the vehicle frame by at least three mounting points following the pendulum test.

The present requirement for booster with belt guides for the diagonal belt is more stringent than for boosters without belt guides. This proposal aligns the requirement for belt disengagement with the requirements for other child restraint systems ((e.g. the displacement criteria and the criteria as indicated in Annex 15, para. 6.2.4.) and at the same time proposes new language to clarify the affected text.

The text prepared by Spain on behalf of the Technical Services Group (TSG) on Regulation No. 44. The proposed amendment is intended to clarify a number of technical provisions in the regulation.

Across its various groups, WP.29 has been looking at the definitions of technical terms used in its regulations from the standpoint of consistency. The GRSP secretariat has compiled terms and definitions found in the regulations under its purview that differ across regulations (including those under regulations managed by other GR). This document is proposed for consideration as a possible starting point for the development of a “dictionary” of harmonized terms and definitions.

Proposal to clarify that the recently increased height requirements for the effective upper belt anchorage (Supplement 4 to the 07 series of amendments to UN Regulation No. 14) can be satisfied by means of a “belt adjustment device for height” that is part of the belt-anchorage as well as a device that is part of the belt itself, each with a distinctive approach. The proposals are presented as draft Supplement 7 to the 07 series of amendments to Regulation No. 14 and draft Supplement 6 to the 06 series of amendments to Regulation No. 16.

Proposal by the GRSP secretariat to delete Appendix 3 (examination of the mobile impact barrier) to Annex 5 of UN R95. The secretariat suspects that the appendix is superfluous, but wishes to confirm if Appendix 3 should remain for any examination purposes of the Type Approval Authority responsible for the mobile deformable barrier.

Proposal for amendments to clarify and correct the current text of the draft regulation on the safety of electric L-category vehicles.

Updated version of the proposed 01 series of amendments to UN R129 prepared by the Informal Group on Child Restraint Systems. The amendments propose to extend the scope of the regulation to cover non-Integral child restraint systems (“Universal Booster” or “Specific to vehicle Booster”) (Phase 2 of the UN Regulation).

Proposal revising an initial German proposal, with the new suggested requirements under 6.3.1.1, to reduce the risks of a person being unintentionally “full locked” inside a locked vehicle, taking into account the anti-theft benefits of fully locking door systems.

Presentation by the secretariat to open discussion of issues related to the introduction of provisions for electrified vehicles and systems within the context of the International Whole Vehicle Type Approval (which allows Contracting Parties to grant approvals under earlier series of amendments).

Explanation of the steps taken to transpose the provisions of GTR No. 14 into a type-approval UN Regulation on pole side-impact protection, including discussion of the scope, impact side, treatment of hydrogen vehicles, and proposal for a 01 series of amendments that would entail a 26 km/h impact speed for narrow vehicles initially before the amendments would bring narrow vehicles into line with other vehicles at 32 km/h.

Correction to include provisions for the exemption of certain headrests of M₂ and M₃ vehicles approved according to UN R80.

Proposal to clarify the requirements of UN R100 specified under paragraph 5.1.1. This paragraph describes the general requirements for the protection of all high voltage parts, including the obligation that such protection against live parts cannot be opened without the use of tools. If connectors can be opened without use of tools or if they do not satisfy the IPXXD/IPXXB protection limits, the provisions of 5.1.1.3 have to be met.

Proposal to define the moment of intertia in the luggage-impact test as “0.3 ± 0.05 kgm² (around all 3 principal axis of inertia of the luggage blocks)”. UN R17 presently lacks such a definition, resulting in variations in trajectory and behavior of the luggage cubes before and after impact.

Proposal to clarify the requirements of UN R100 specified under paragraph 5.1.1. This paragraph describes the general requirements for the protection of all high voltage parts, including the obligation that such protection against live parts cannot be opened without the use of tools. If connectors can be opened without use of tools or if they do not satisfy the IPXXD/IPXXB protection limits, the provisions of 5.1.1.3 have to be met.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Presentation of an assessment of 2D vs. 3D impactor positioning methods.

Presentation summarizing the draft new regulation on the safety of electric motorcycles and other L-category vehicles.

Text incorporating informal documents GRSP-55-07 and GRSP-55-22 and amending ECE/TRANS/WP.29/GRSP/2014/11 as prepared by the Informal Working Group (IWG) on Rechargeable Energy Storage System (REESS) proposing to establish a new UN Regulation annexed to the 1958 Agreement on electric vehicles of category L. Paragraphs in square brackets were not agreed by GRSP experts as outcome of discussion of its 55th session.

Draft text transposing the provisions of GTR No. 13 into a new UN Regulation for the type approval of hydrogen fuel-cell vehicles with regard to safety performance. This text supersedes document GRSP/2013/22 and reflects the results of informal discussions among the European Commission, Japan and OICA.

Proposal to amend the scope and clarify the transitional provisions to avoid misinterpretations for the installation of side-facing seats in category M₃vehicles. The proposal exempts vehicles exceeding 10 tonnes from the prohibition on side-facing seat provided the seat meet conditions specified in the 03 series of amendments to the Regulation.

Text to add a paragraph concerning fuel cell vehicles unintentionally omitted from the original draft document GRSP/2014/11.

Proposal to clarify the prohibition of side-facing seats on category N vehicles and close the related loophole in the current text in this regard.

Proposal to replace references to “hydrogen fuelled” with “hydrogen fuel cell” in order to exclude application to liquefied hydrogen storage systems.

Proposal to clarify figure 11 in the draft amendments to GTR No. 9 by substituting the description “Figure 11: Example of marking of HIC 1000 zone and HIC 1700 zone”.

Presentation on Japan’s evaluation of the use of three- or four-wheeled “New Mobility Vehicles” with a passenger capacity of 2 persons and smaller than M1 category as a way to diversify transportation means and offer environmental countermeasures.

Proposal to add classifications covering agricultural trailers and towed agricultural machinery in the Consolidated Resolution on the Construction of Vehicles (R.E.3) transmitted from GRSG to GRSP for input.

Draft text transposing the provisions of GTR No. 13 into a new UN Regulation for the type approval of hydrogen fuel-cell vehicles with regard to safety performance. This text supersedes document GRSP/2013/22, incorporates changes requested by Korea (document GRSP-55-23) and reflects the results comments received during the 55th GRSP session.

The current text of UN R14 requires the installation of two ISOFIX anchorages in a vehicle. Vehicles with only one seat row are exempted from this requirement. This proposal refines the previous German proposal to introduce provisions for at least one set of ISOFIX anchorages in vehicles having only one seat row or having several seat rows with only one seat per row (document GRSP-53-11) which modified the proposal for Supplement 6 to the 07 series of amendments (document GRSP/2013/15).

Slide illustrating vehicle types intended to be exempted from the ISOFIX requirements of UN R14 under the proposed classification according to R-point measurement.

Presentation on the development of the regulation on enhanced child restraint systems, including review of the current phase 2 on booster and related seats and plans for phase 3 on stand-alone belted integral CRS.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments).

Proposal revising an initial German proposal to reduce the risk of a person being unintentionally locked inside a vehicle by an anti-theft system. This proposal would either prohibit systems that could lock an occupant inside a vehicle (by requiring an occupant detection capability) or require warning systems (such as a horn) that can be activated from inside the vehicle even when it is fully locked.

Presentation on the promising results of research into the use of shield systems to secure children in child seats.

Presentation of a question and answer information sheet on the introduction of UN Regulation No. 129.

Presentation on the main principles behind the new enhanced child restraint systems provisions:

1. Modern dummy and criteria
2. Classification based upon child size
3. Integral universal ISOFIX
4. Side-impact protection
5. Mandatory rear-facing up to 15 months
6. improved compatibility

The draft Amendment 2 to GTR No. 9 proposes to establish the new FlexPLI impactor as the single harmonized tool for lower leg impact tests. The amendment also proposes injury assessment reference values (IARV) to go with the FlexPLI. The US, however, has consistently expressed concerns that the proposed injury thresholds and IARV have not been validated as appropriate for the American car fleet. Therefore, the US proposes to have ‘recommended’ IARV included in the preamble to Amendment 2 while allowing governments the freedom to use whatever IARV/performance thresholds they deem appropriate until such criteria can be fully validated.

Presentation on child restraint fixtures (CRF) and their relationship with in-vehicle safety systems, arguing that children benefit from certain CRF configurations that position the occupant for optimal benefit of seat belts or for eventual interaction with a side/curtain airbag.

Proposal to align UN R44 with UN R129 with respect to the references to European standard EN 71:2009 (which specifies safety requirements for toys, especially with regard to chemical composition, flammability, and other mechanical and physical properties).

Updated proposal to clarify various technical provisions as developed by the Technical Services Group (TSG) on Regulation No. 44.

OICA presentation arguing for chest deflection threshold of 42 mm for the 5th Female H-III dummy.

Proposal to amend the draft 01 series of amendments (document WP.29/2014/38 pending for the June 2014 WP.29 session) to bring its “commencement date” and validity-of-approvals provisions into line with the recommendations for the International Whole Vehicle Type Approval system (i.e., to set the effective date to 1 September 2018 and confirm the validity of earlier approvals after the introduction of the 01 series of amendments). This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to remove the specification of “±0.01 m/sec” for the accuracy of the velocity measurement in Annex 5, Paragraph 3.2.1. This would leave in place the specification to use the measurement procedure if ISO 3784:1976 which specifies an accuracy of ±1 %.

Updated proposal to add provisions agreed during the last Frontal Impact informal group meeting regarding the position of the front passenger following discussions at the 55th GRSP session.

Proposal pursuant to discussions at the 55th GRSP session to revise an initial German proposal to reduce the risk of a person being unintentionally locked inside a vehicle by an anti-theft system. This proposal would either prohibit systems that could lock an occupant inside a vehicle (by requiring an occupant detection capability) or require warning systems (such as a horn) that can be activated from inside the vehicle even when it is fully locked.

Draft text prepared by the Task Force Bumper Test Area (TF-BTA), a subgroup of the Informal Working Group on gtr No. 9 – Phase 2.

Corrections to draft text and revision of entry into force dates to occur on 1 September following IWVTA recommendations. This revised document also incorporates the Korean proposal to amend GTR No. 9 (document GRSP-55-24) and OICA proposal on Annex 5 (document GRSP-55-44).

Proposal to require that a horn or other acoustic signalling system can be activated from within a parked vehicle when in the fully locked mode and to set the transition period through 1 September 2016 for meeting the new requirement.

Draft text for the transposition of GTR No. 13 on hydrogen and fuel-cell vehicle safety into a new UN Regulation under the 1958 Agreement. This version incorporates comments received by GRSP at its 55th session and informal document GRSP-55-23 from the expert of Rep. of Korea.

Proposal for a new UN Regulation transposing the requirements of the UN Global Technical Regulation on pole side impact (GTR No. 14). This proposal is accompanied by a proposal for a 01 series of amendments (documentGRSP/2014/12) that would enable Contracting Parties applying this Regulation to require a vehicle-to-pole impact speed of 32 ± 1 km/h regardless of the “vehicle width”. This proposal supersedes the earlier version presented in document GRSP/2014/9.

Proposal as revised during the 55th GRSP session (superseding document GRSP/2014/06) incorporating changes to UN R94 in light of the development of the new regulation concerning protection in frontal collisions with focus on the restraint system, especially to improve the protection of older occupants.

Proposal by the secretariat to correct a reference to UN R25 to refer to the 04 series of amendments rather than to the 03 series of amendments.

Proposal by the secretariat to correct a reference to UN R25 to refer to the 04 series of amendments rather than to the 03 series of amendments.

The 03 series of amendment introduced a new Test C into UN Regulation No. 29. This proposal adds specifications for the test rig in the case where a pendulum impactor is used (as is already prescribed for Tests A and B. To improve the repeatability of the test, the submission further proposes to place the cab on a horizontal surface and to fix the pendulum with a required angle of 20° of impact against the cab to be tested.

Draft of the amendment to introduce the Flex PLI lower legform impactor and related test procedures into the GTR on pedestrian safety protection, including the new bumper test area specifications.

Germany submitted a proposal that would require at least one set of ISOFIX anchorages in single-row vehicles (which are currently exempted under UN R14). This proposal (superseding GRSP-55-31) would set a minimum R-point criteria for requiring the ISOFIX anchorages and thus exempt vehicles with R-points below this minimum height. The purpose is to exempt sport vehicles not intended to carry small children requiring child seats from the ISOFIX requirement.

Proposal to define the moment of intertia in the luggage-impact test as “0.3 ± 0.05 kgm2 (around all 3 principal axis of inertia of the luggage blocks)”. UN R17 presently lacks such a definition, resulting in variations in trajectory and behavior of the luggage cubes before and after impact.

Proposal to extend the prohibition against the installation of side-facing seats to all categories of commercial vehicles (N).

Proposal as revised during the 55th GRSP session (superseding document GRSP/2014/06) incorporating changes to UN R94 in light of the development of the new regulation concerning protection in frontal collisions with focus on the restraint system, especially to improve the protection of older occupants.

Text prepared by the Informal Working Group on Frontal Impact (IWG FI) to introduce necessary modifications to the draft UN Regulation on frontal impact focusing on requirements for restraint systems (GRSP/2014/10).

Proposal by the GRSP secretariat to delete Appendix 3 (examination of the mobile impact barrier) to Annex 5 of UN R95. Appendix 3 was rendered redundant by the 02 series of amendments to the regulation (which introduced the EEVC mobile deformable barrier).

Amendment to introduce all the modifications needed in UN Regulation No. 129 (Enhanced Child Restraint System (ECRS)) that were suggested by the experts of the informal working group on Child Restraint Systems (IWG CRS) to extend the scope of this Regulation to Non-Integral child restraint systems (“Universal Booster” or “Specific to vehicle Booster”) (Phase 2 of the UN Regulation).

CLEPA proposal to clarify dynamic testing, rear seat system approval and transitional provisions.

Proposal to amend the scope and clarify the transitional provisions to avoid misinterpretations for the installation of side-facing seats in category M3 vehicles. The proposal exempts vehicles exceeding 10 tonnes from the prohibition on side-facing seat provided the seat meet conditions specified in the 03 series of amendments to the Regulation.

Text prepared by the Informal Working Group of Rechargeable Energy Storage System (IWG REESS) to resolve open issues concerning the draft new UN Regulation on L-category vehicle electric powertrains (document GRSP/2014/11).

Proposal to require automatically folding/unfolding exterior mirrors to unfold automatically once the vehicle speed exceeds five km/h. This document supersedes documents GRSG-105-28 and GRSG/2014/17.

Corrections proposed to document GRSP/2014/26 which introduced amendments to the draft regulation as presented in document GRSG/2014/11.

Proposal from the Bumper Test Area Task Force to revise the procedure for determining the bumper test area under the pedestrian safety regulation. This proposal corrects shortcomings in the current definitions which could lead to a narrower test area than intended (leading to less effective pedestrian protection). This proposal does not take into account potentially harmful hard structures such as bumper beams that may lie behind the outer contour or front fascia extending beyond the defined bumper corners as consensus within the task force could not be reached.

Proposal from the Bumper Test Area Task Force, submitted as an alternative to the proposal in document GRSP/2014/17, to revise the procedure for determining the bumper test area under the pedestrian safety regulation. This proposal corrects shortcomings in the current definitions which could lead to a narrower test area than intended (leading to less effective pedestrian protection). This proposal includes a “bumper beam” determination method.

Proposal from the Bumper Test Area Task Force to revise the procedure for determining the bumper test area under the pedestrian safety regulation. This proposal corrects shortcomings in the current definitions which could lead to a narrower test area than intended (leading to less effective pedestrian protection). This proposal does not take into account potentially harmful hard structures such as bumper beams that may lie behind the outer contour or front fascia extending beyond the defined bumper corners as consensus within the task force could not be reached. Presented as a Supplement, the proposal includes a September 2017 transition date in case GRSP determines that the changes should be put into a new series of amendments rather than as a supplement.

Proposal from the Bumper Test Area Task Force, submitted as an alternative to the proposal in document GRSP/2014/31, to revise the procedure for determining the bumper test area under the pedestrian safety regulation. This proposal corrects shortcomings in the current definitions which could lead to a narrower test area than intended (leading to less effective pedestrian protection). This proposal includes a “bumper beam” determination method. The proposal also includes a September 2017 transition date in the event that the GRSP determines that the proposal should be treated as a new series of amendments rather than as a Supplement.

Addition of new document references to the agenda.

Update on the work concerning head restraint height measurement, dynamic test for rear impacts, BioRID II dummy certification and R&R, GTR “whiplash” injury criteria, and introduction of the BioRID test tool into the Mutual Resolution 1 compendium.

Proposal to expand the application area of the energy absorption criteria for seating in order to facilitate the optimization of seat-belt load limiters by allowing limited occupant contact with these seat areas.

Revised amendment to introduce all the modifications needed in UN Regulation No. 129 (Enhanced Child Restraint System (ECRS)) that were suggested by the experts of the informal working group on Child Restraint Systems (IWG CRS) to extend the scope of this Regulation to Non-Integral child restraint systems (“Universal Booster” or “Specific to vehicle Booster”) (Phase 2 of the UN Regulation).

Revised CLEPA proposal to clarify dynamic testing, rear seat system, advanced restraint system approval, and transitional provisions. This proposal supersedes document GRSP/2014/27.

The scope of the new Global Technical Regulation on Pole Side Impact includes vehicles of category N1 (limited to GVM < 3.5 t) and vehicles of category M1 (without mass limit). However, the vehicle fleet includes a small number of M1 vehicles with a GVW > 3.5t which are based on vehicles of category N2, N3, M2 or M3. Therefore, OICA proposes to limit the scope of the GTR to both M1 and N1 vehicles under 3.5 t maximum vehicle mass in order to alleviate burdens on manufacturers producing M1 variants based on N2, N3, M2, or M3 vehicles.

Proposal to introduce provisions concerning universal child booster seating positions.

Proposal to introduce provisions concerning universal child booster seating positions with the amendments shown within the text of the regulation, incorporating the amendments proposed in document GRSP/2014/14.

Editorial improvements to the text and introduction of provisions allowing for the separation of connectors (including the vehicle inlet) without the use of tools under prescribed conditions.

Editorial improvements to the text and introduction of provisions allowing for the separation of connectors (including the vehicle inlet) without the use of tools under prescribed conditions.

Proposal to clarify the text related to the recently expanded height requirements for the effective upper belt anchorage (Supplement 4 to the 07 series of amendments to Regulation No. 14).

Text prepared by the UN R44 Technical Services Group to clarify the regulation, including test failure parameters, CRS displacement or locking systems, seat installation color coding systems, and use of load limiting devices. The test procedure would be modified, including an increase in the applied load to exceed the maximum allowed resistance to permit sliding of the strap through the quick adjuster and through rigid parts, increased tolerances related thereto, deletion of the option for shorter shift (deemed unnecessary since it is a test on the strap, not on the complete component), and modification of drawings to improve consistency with the text.

Revised amendment, including track changes, to introduce all the modifications needed in UN Regulation No. 129 (Enhanced Child Restraint System (ECRS)) that were suggested by the experts of the informal working group on Child Restraint Systems (IWG CRS) to extend the scope of this Regulation to Non-Integral child restraint systems (“Universal Booster” or “Specific to vehicle Booster”) (Phase 2 of the UN Regulation).

Request for clarifications on the application of relaxation areas under UN Regulation No. 127.

Request for clarification of test procedures for active pedestrian protection devices (such as active hood, pedestrian airbag).

Japan is developing national legislation to prescribe requirements for the body, hydrogen storage containers and their specific components, batteries etc. of hydrogen fuel-cell powered motorcycles.

Proposal to include “MFP” in the labeling requirement for hydrogen containers. MFP refers to the maximum allowable container pressure under normal use.

Proposal to amend the toxicity and flammability declarations via references to EN71 (European safety standards).

Question and answer brochure on the i-size child restraint systems regulation.

Report on the phase 2 development (regarding universal booster seats and cushions) of UN Regulation No. 129.

Presentation on occupant protection tests of selected L7 category vehicles (e.g., very light, limited maximum speed road vehicles that do not require a driver’s license to operate).

Fact sheet on UN R129 including comparison with UN R44.

The scope of the new Global Technical Regulation on Pole Side Impact includes vehicles of category N1 (limited to GVM < 3.5 t) and vehicles of category M1 (without mass limit). However, the vehicle fleet includes a small number of M1 vehicles with a GVW > 3.5t which are based on vehicles of category N2, N3, M2 or M3. Based on the OICA proposal (document GRSP-56-12) and ensuing discussions, Australia proposes to limit the scope of the GTR to both M1 vehicles under 3.5 t maximum vehicle mass and to certain N1 vehicles based on geometric measurements.

Proposal to prohibit the use of Y-shaped belt on forward-facing child restraint system. This proposal aligns UN R129 with provisions already in UN R44.

Proposal to exclude “bucket seats” from the ISOFIX requirements as well as vehicles with only one seating position (by applying the regulation only to vehicles with more than one seating position). The proposal also exempts certain vehicle/seating configurations from ISOFIX requirements, addressing cases where the vehicle design and purpose mitigate against the use of such child restraints and ISOFIX systems.

Thorax compression criterion (ThCC) under the draft new regulation on frontal impact protection and occupant restraint systems.

Proposal from the Bumper Test Area Task Force to revise the procedure for determining the bumper test area under the pedestrian safety regulation. This proposal corrects shortcomings in the current definitions which could lead to a narrower test area than intended (leading to less effective pedestrian protection). This proposal does not take into account potentially harmful hard structures such as bumper beams that may lie behind the outer contour or front fascia extending beyond the defined bumper corners as consensus within the task force could not be reached.

Proposal from the Bumper Test Area Task Force, submitted as an alternative to the proposal in document GRSP/2014/17 as amended by document GRSP-56-38, to revise the procedure for determining the bumper test area under the pedestrian safety regulation. This proposal corrects shortcomings in the current definitions which could lead to a narrower test area than intended (leading to less effective pedestrian protection). This proposal includes a “bumper beam” determination method.

Proposal from the Bumper Test Area Task Force, pursuant to discussions within GRSP, to revise the procedure for determining the bumper test area under the pedestrian safety regulation. This proposal corrects shortcomings in the current definitions which could lead to a narrower test area than intended (leading to less effective pedestrian protection). This proposal does not take into account potentially harmful hard structures such as bumper beams that may lie behind the outer contour or front fascia extending beyond the defined bumper corners as consensus within the task force could not be reached. Presented as a Supplement, the proposal includes a September 2017 transition date in case GRSP determines that the changes should be put into a new series of amendments rather than as a supplement.

Proposal from the Bumper Test Area Task Force, pursuant to discussions within GRSP, submitted as an alternative to the proposal in document GRSP/2014/31 as amended by document GRSP-56-40, to revise the procedure for determining the bumper test area under the pedestrian safety regulation. This proposal corrects shortcomings in the current definitions which could lead to a narrower test area than intended (leading to less effective pedestrian protection). This proposal includes a “bumper beam” determination method. The proposal also includes a September 2017 transition date in the event that the GRSP determines that the proposal should be treated as a new series of amendments rather than as a Supplement.

In June 2014, WP.29 returned a proposal (document WP.29/2014/34) to introduce provisions for ISOFIX positions in convertibles and vehicles with one seating position per row due to concerns over clarity. Given the complexity of this topic, OICA has decided to address specific elements separately. This proposal addresses the use of top tethers in child restraint systems and proposes to retain the “i-size” term and definition endorsed by GRSP.

Further refinements to the proposed new regulation on frontal impact protection in relation to occupant restraint systems (document GRSP/2014/10 amended by doument GRSP/2014/23) prepared by the Informal Group on Frontal Impact. These amendments concern provisions on the position of the front passenger.

Further refinements to UN R94 frontal impact regulation in light of the new regulation on frontal impacts and occupant restraint systems currently pending approval.

Proposal from Japan to outline a 01 series of amendments to the draft new UN Regulation with regard to the Full Width Rigid Barrier test. This proposal would enable Contracting Parties to apply this Regulation with a Thorax Compression Criterion (ThCC) of 34 mm for the Hybrid III 5th female dummy on the passenger seat in the event that both the 00 series draft new regulation and the 01 series amendments are adopted concurrently.

Argument in favor of extending provisions for seat-belt reminders to the rear seating positions, particularly to respond to low seat-belt use by rear occupants and the associated higher rates of death and injury in accidents.