Draft 02 series of amendments to Regulation No. 129

Hungary agrees with the proposed change to the airbag label, but recommends the addition of transitional provisions.

Updated proposal from Spain on behalf of the CRS Technical Services Group to align requirements for deceleration test devices with acceleration ones (making explicit that it is mandatory to match the corridor for each test) and to add dummy criteria and compliance with ISO 17025 to the information required in test reports.

Proposal from Spain on behalf of the CRS Technical Services Group to

• to align paragraph 6.6.3.1. with the 01 series of amendments,
• to align requirements in 7.1.3.1 to test methods in 8.1.2.4.,
• to add tolerances to better define the test method in paragraph 8.1.2.3.,
• to improve the specifications for the measurement of dimensions C and D in Annex 23,
• to align deceleration test requirements with acceleration test provisions (making explicit that it is mandatory to match the corridor for each test, and
• to define the initial acceleration value under paragraph 7.3. against which the maximum deviation restriction is to be applied.

Amendment to the proposals (GRSP/2016/3, GRSP/2016/5, and GRSP/2016/6) to amend the toxicity and flammability declarations via references to EN 71 (European safety standards), taking into account procedures of FMVSS 302. The amendments propose the burning rate values of FMVSS 302 (302.4 inches/102 mm per minute), to harmonize the three proposals with regard to EN standards references, and to incorporate the amendment 1 to EN 71-3 (A1:2014).

Proposal to change the burn-rate in documents GRSP/2016/3, GRSP/2016/5, and GRSP/2016/6 from [250 mm] to the equivalent of the FMVSS 302 specification, i.e., 100 mm.

Proposal to introduce provisions for seat-belt reminders for all vehicle seating positions pursuant to the outcome of the Task Force on Seat-belt Reminders discussions.

Updated proposal from the CRS informal group to introduce phase 2 amendments related to the booster-seat CRS category (booster seat with backrest) into UN R129. This document updates the proposal in document GRSP/2016/4.

UN R80, paragraph 7.4.4. specifies that passengers in side-facing seats “shall be safeguarded by a vehicle part (e.g. partition, wall or seat back of a forward-facing seat) forward of the foremost side-facing seat”. Germany has determined that the current text has been misinterpreted with regard to the intended requirement for a safety device that does not break and maintains its capability to retain a passenger’s body in the event of an accident. This proposal clarifies that such any such structure “shall retain its safeguard function during testing”.

Proposal to strip ISOFIX CRS provisions from UN R44 and to cease all new type approvals for ISOFIX integral CRS under UN R44 from [November 2016] in deference to UN R129 on Enhanced CRS.

Draft of a request for authorization to amend GTR 9 to include provisions for deployable safety systems of the outer surface of the vehicle. This proposal originates with the development of technologies such as active hood/bonnet mechanisms that improve pedestrian impact protection. The proposal anticipates submission of a formal amendment for the June 2018 WP.29 session.

Presentation concerning technical discussions, conclusions, and proposals for CRS bench seat cushion drop tests under UN R44 and UN R129.

NHTSA presentation on the agency’s experience and investigations concerning low-speed vehicles and three-wheeled motorcycles. This presentation broadly considers very light vehicles mainly intended for local (neighborhood), short-distance transportation.

Proposal to clarify the “Minimum requirements for safety-belts and Retractors” table in Annex 16.

Proposal drafted by OICA pursuant to cooperation among the EU, Consumers International, Governmental experts, Euro NCAP, OICA and CLEPA to restructure and simplify the consumer information requirements on the installation of ISOFIX child restraint systems under UN R16.

Consolidated version of UN R129 including the proposals for the 02 series of amendments (WP29/2016/107), Supplement 1 to the 02 series of amendments (GRSP/2016/19), and Supplement 2 to the 02 series of amendments (GRSP/2016/22). The 02 series concerns the “phase 2” amendments regarding the approval of booster-seat CRS category (booster seat with backrest). Supplement 1 updates the toxicity and flammability of materials provisions pursuant to Supplement 1 to the 01 series of amendments. Supplement 2 proposes editorial improvements and corrections to the original text.

Revision 3 of the 1958 Agreement allows for a Unique Identifier (UI) under the DETA system as an alternative to the current approval mark. In the case of child restraint systems, the approval mark contains important information for users. Therefore, this proposal would prohibit replacement of the approval mark by the UI.

Proposal to transfer all ISOFIX requirements from UN R14 into a new UN Regulation. Within the context of the international whole vehicle type approval program, the removal of these CRS anchorage provisions would align UN R14 with its Australian Design Rule counterpart and enable Australia to apply the revised UN R14 narrowed down to adult seat-belt anchorages only.

Per the proposal to narrow the scope of UN R14 (GRSP-60-04), this proposal would consolidate the provisions for child restraint anchorages deleted from UN R14 as a new UN Regulation.

Proposal to add references to the steering gear provisions of UN R137 (full width frontal impact) as a compliance alternative in addition to the current references requiring compliance with similar provisions in UN R94 (offset deformable barrier frontal impact).

Proposal to apply a minimum burst pressure (BPmin) in place of the current COP that only requires the manufacturer to provide mid-burst pressure with specified variation. The proposal also deletes the phrase “and in no case less than the value necessary to meet the stress ratio requirements” which was erroneously copied into the regulation.

Proposal to clarify and make editorial corrections to the text of the 02 series of amendments to the UN Regulation No. 129. This proposal supersedes document GRSP/2016/23 and amends WP.29/2016/107 (02 series of amendments to the UN Regulation) and GRSP/2016/19 (Proposal for Supplement 1 to the 02 series of amendments to Regulation No. 129).

Proposal to clarify and make editorial corrections to the text of the 02 series of amendments to the UN Regulation No. 129. This proposal supersedes document GRSP/2016/22 and amends WP.29/2016/106 (02 series of amendments to the UN Regulation).

This informal doc amends the draft supplement presented in document GRSP/2016/24 in order to harmonize the mass tolerances of the ISO fixtures. The proposal deletes a reference to the center of gravity and geometrical centroid. The centroid would need more information before choosing tolerances needed for certification tests.

This informal doc amends the draft supplement presented in document GRSP/2016/21 in order to harmonize the mass tolerances of the ISO fixtures. The proposal deletes a reference to the center of gravity and geometrical centroid. The centroid would need more information before choosing tolerances needed for certification tests.

The current paragraph 15.6 foresees that, for type approval to the 07 series, safety belt reminders are not compulsory until 1 September 2022 on the exempted seats (e.g. seat rows with a suspension seat). In the absence of any clarification for the case of extensions of type approvals, paragraph 15.6 of UN R16.07 could create interpretation problems when a previously granted approval for an exempted vehicle needs to be extended after 1 September 2022. As previously agreed by GRSP, this proposal would clarify that the new SBR requirements would be applicable only for new type approvals as from 1 September 2022, such that previously granted approvals would remain accepted, with their exemption.

Draft text presented by the EVS informal group for GRSP discussion and consideration.

Proposal to add the Q0 infant test dummy to the UN R44 procedures in response to problems encountered in acquiring the currently specified P0 dummy.

Proposal to resolve divergent interpretations with regard to child restraint systems in UN Regulation No. 44, superseding document GRSP/2016/18.

Announcement of task force establishment, organization, and meeting plans towards developing a proposal for the assessment and approval of deployable exterior pedestrian safety systems (e.g., active bonnet).

Phase 2 proposes to amend the UN Global Technical Regulation No. 9 on pedestrian safety by introducing the flexible pedestrian legform impactor (FlexPLI) as a single harmonized test tool in order to enhance the level of protection for pedestrian lower legs. NHTSA has expressed concern that the injury assessment reference values (IARVs) for this GTR may not meet the needs for injury mitigation in the U.S. In order to enable the proposed Phase 2 amendment to move forward with US support, the US proposes additions to the GTR preamble to make clear its position and intentions regarding assessment of the IARV and to allow the brackets to be removed from the IARV in the draft amendment.

Explanation of the proposals in document GRSP/2016/18 intended to resolve divergent interpretations with regard to child restraint systems in UN Regulation No. 44.

Proposal to correct figure 2 in Annex 1B to show the referenced zones A and B, to add sentence “Non-rigid material of < 50 Shore A hardness may be removed in order to demonstrate that covered or padded rigid parts are not contacted by the head or the chest of the manikin during the test.”, and to make editorial improvements.

Final report, pursuant to the amendment’s approval by GRSP, to accompany the amendment to align the specifications for back doors with those of side doors with rear mounted hinges as established in UN Regulation No.11.

Draft proposal for eventual submission to WP.29 for the further development of the GTR on hydrogen fuel-cell vehicle safety, including the following additional areas for consideration:

1. Scope revision to address additional vehicle classes;
2. Requirements for material compatibility and hydrogen embrittlement;
3. Requirements for the fuelling receptacle;
4. Evaluation of performance-based test for long-term stress rupture proposed in Phase 1;
5. Consideration of research results reported after completion of Phase 1 – specifically research related to electrical safety, hydrogen storage systems, and post-crash safety;
6. Consideration of 200 per cent NWP or lower as the minimum burst requirement;
7. Safety guard system for the case of isolation resistance breakdown.