Proposal from GRE to introduce transitional provisions for the phasing out of UN R3 in conjunction with the introduction of the new simplified Regulation on Retro-Reflective Devices (RRD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R4 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R6 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R7 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R19 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R23 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R27 in conjunction with the introduction of the new UN Regulation on Retro-Reflecting Devices (RRD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R38 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R50 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R69 in conjunction with the introduction of the new UN Regulation on Retro-Reflecting Devices (RRD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R70 in conjunction with the introduction of the new UN Regulation on Retro-Reflecting Devices (RRD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R77 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R87 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R91 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R98 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R104 in conjunction with the introduction of the new UN Regulation on Retro-Reflecting Devices (RRD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R112 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R113 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R119 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R123 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Proposal to amend Annex 7 (laminated-glass panes), inserting a new paragraph 6 to allow optional 2,260 g ball test and headform test for laminated-glass panes. The proposal adds the marking “/D” to signify laminated-glass panes subjected to the 2,260 g ball test and the headform test. The proposal aims to enable the approval of laminated-glass panes with improved mechanical properties, especially as designed for front, exterior, forward-facing glazing of the upper deck of a double-deck vehicle.

Proposal to clarify that overlays may only be used to convey “safety-related rearward vision information.” The proposal addresses confusion regarding circumstances under which the provision of information through overlays is permissible. The proposal also amends the French text. The overall proposal aims to make clear that overlays may convey safety information regarding the rearward environment of the vehicle and are not necessarily limited only to when the vehicle is moving in reverse. The proposal also aims to restrict the information to rear-vision safety. Other information, not related to the rear view, should never appear within the defined field of view. The proposal also corrects the omission of Class VII devices from the communication form described under Annex 3 of the regulation, as previously adopted for Revisions 5 and 6.

Proposal to define visibility requirements for external gas containers and their accessories to facilitate periodic inspections. From 1 September 2020, Contracting Parties may refuse approvals under the 01 series issued after 1 September 2020.

Proposal to clarify visibility requirements for CNG cylinders, LNG tanks, and their accessories to facilitate external inspections (e.g. for periodic technical inspection).

Proposal to align UN R105 with provisions adopted by the Working Party on the Transport of Dangerous Goods (WP.15) under the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR), edition 2019.

Proposal to amend the transitional provisions in order to explicitly confirm that under the new guidelines on UN Regulation procedures (documents WP.29/2017/107 including Corrigendum 1 and Addendum 1), approvals granted under the preceding series of amendments will continue to be accepted. This amendment thus confirms the understanding that the new procedures apply only to new approvals and do not affect previous approvals.

Proposal to correct an oversight by adding the minimum requirement for at least a two-point lap belt (Br3, Br4m, Br4Nm) for use with rearward facing child restraints for M₃ as is already the case for M₂ vehicles.

Proposal to correct an oversight by adding the minimum requirement for at least a two-point lap belt (Br3, Br4m, Br4Nm) for use with rearward facing child restraints for M₃ as is already the case for M₂ vehicles.

Proposal to introduce installation specifications for securing a cab mounted on a vehicle to the test rig for tests B and C, as is currently provided for test A, under UN R29. This proposal aims to improve repeatability and reproducibility while allowing more flexibility in permitting the use of rigid composite blocks and/or (adjustable) metal brackets in securing the vehicle in the place of the wooden block presently prescribed in Figure 1.

Proposal to harmonize airbag warning labels regarding the correct use of a child restraint system in a seating position equipped with an activated frontal airbag in order to prohibit the display of additional information unrelated to child safety.

Proposal to harmonize airbag warning labels regarding the correct use of a child restraint system in a seating position equipped with an activated frontal airbag in order to prohibit the display of additional information unrelated to child safety.

Proposal to clarify the conditions where a door is deemed to be open under UN R95. Technical Services have interpreted the definition of “open” under paragraph 5.3.1. differently, resulting in divergent outcomes. The proposed definitions are taken from UN Regulation No. 135 Revision 1. The proposal reduces the force level from 500 N to 400 N for the test to open the door.

Proposal to amend the transitional provisions in order to explicitly confirm that approvals granted prior to the respective supplements to the 01 and 02 series of amendments and the establishment of the new guidelines on UN Regulation procedures (documents WP.29/2017/107 including Corrigendum 1 and Addendum 1) will continue to be accepted. This amendment confirms the understanding that the new procedures apply only to new approvals and do not affect previous approvals.

Proposal to amend the transitional provisions in order to explicitly confirm that approvals granted prior to the respective supplements to the 01 and 02 series of amendments and the establishment of the new guidelines on UN Regulation procedures (documents WP.29/2017/107 including Corrigendum 1 and Addendum 1) will continue to be accepted. This amendment confirms the understanding that the new procedures apply only to new approvals and do not affect previous approvals.

Proposal to align end-user information provisions with those adopted for UN R44.

Proposal to

1. require that the shoulder strap positioner, if any, and the buckle open independently of each other in order to satisfy the requirement that the buckle can be opened by a single action;
2. align end-user information provisions with that adopted for UN R44;
3. reinsert text omitted during the transcription of the adopted texts of Supplement 3 to the 01 series of amendments and Supplement 2 to the 02 series of amendments; and
4. harmonize airbag warning labels regarding the correct use of a child restraint system in a seating position equipped with an activated frontal airbag in order to prohibit the display of additional information unrelated to child safety.

Proposal to

1. require that the shoulder strap positioner, if any, and the buckle open independently of each other in order to satisfy the requirement that the buckle can be opened by a single action;
2. align end-user information provisions with that adopted for UN R44;
3. reinsert text omitted during the transcription of the adopted texts of Supplement 3 to the 01 series of amendments and Supplement 2 to the 02 series of amendments; and
4. harmonize airbag warning labels regarding the correct use of a child restraint system in a seating position equipped with an activated frontal airbag in order to prohibit the display of additional information unrelated to child safety.

Proposal to

1. require that the shoulder strap positioner, if any, and the buckle open independently of each other in order to satisfy the requirement that the buckle can be opened by a single action;
2. align end-user information provisions with that adopted for UN R44;
3. reinsert text omitted during the transcription of the adopted texts of Supplement 3 to the 01 series of amendments and Supplement 2 to the 02 series of amendments; and
4. harmonize airbag warning labels regarding the correct use of a child restraint system in a seating position equipped with an activated frontal airbag in order to prohibit the display of additional information unrelated to child safety.

Proposal to introduce references to the three new simplified lighting Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 06 series of Regulation No. 48.

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 05 series of Regulation No. 48.

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 04 series of Regulation No. 48.

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 03 series of Regulation No. 48.

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 02 series of Regulation No. 53.

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 01 series of Regulation No. 53.

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 01 series of Regulation No. 74.

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 01 series of Regulation No. 86.

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the original series of Regulation No. 86.

Proposal to clarify the test requirements in alignment with the French text of the regulation by amending paragraph 5.10 to read “Tanks shall be installed in such a way as to be protected from the consequences of a collision to the front or the rear of the vehicle. There shall be no protruding parts, sharp edges, etc. near the tank.” The proposal aims to clarify the inspection of potentially protruding parts around the tanks in order to ensure their integrity in the event of a collision.

Proposal to clarify the test requirements in alignment with the French text of the regulation by amending paragraph 5.10 to read “Tanks shall be installed in such a way as to be protected from the consequences of a collision to the front or the rear of the vehicle. There shall be no protruding parts, sharp edges, etc. near the tank.” The proposal aims to clarify the inspection of potentially protruding parts around the tanks in order to ensure their integrity in the event of a collision.

Proposal to harmonize airbag warning labels regarding the correct use of a child restraint system in a seating position equipped with an activated frontal airbag in order to prohibit the display of additional information unrelated to child safety.

Proposal to:

1. harmonize airbag warning labels regarding the correct use of a child restraint system in a seating position equipped with an activated frontal airbag in order to prohibit the display of additional information unrelated to child safety, and
2. clarify that only a 3-point-belt shall be permitted for the driver seating position in order to address differing interpretations among Technical Services regarding which requirements apply for driver position seat-belt approval.

Proposal to require seat belt components such as retractors to remain functional if damaged during the load-retention test according to Annex 9 of UN R17. Such components have occasionally been damaged during testing such that their functionality has been impaired. In order to ensure adequate occupant safety, this proposal would require all safety-belt components to be included in the test installation and require post-test inspection to confirm the continued functionality. The transitional provisions phase in the new requirements during September 2020-September 2022.

Proposal to align UN R24 (Compression Ignition Engines – Emission of Visible Pollutants – Power Measurement) with UN R85 with regard to correction factors.

Proposal to modify the Constant Volume Sampling system temperature sensor time response requirement.

Proposal to modify the Constant Volume Sampling system temperature sensor time response requirement.

Proposal to modify the Constant Volume Sampling system temperature sensor time response requirement.

Proposal to

1. clarify the fuel tank capacity restriction for mono-fuel gas vehicles (insertion of word “nominal” in definition of “mono-fuel gas vehicle”;
2. modify the Constant Volume Sampling system temperature sensor time response requirement;
3. allow the use of WLTP-based Ki and Deterioration Factors (DF) as well as On-Board Diagnostics (OBD) demos under UN R83 to permit use of WLTP methods and test results under UN R83;
4. align the definitions for bi-fuel vehicles align with the new definitions in UN GTR 15,
5. amend paragraph 5.3.1.2.4. to recognize that particulate pollutant emissions measurements are no longer limited to compression ignition vehicles;
6. introduce provisions for reagent tank specifications and limits for triggering warning and driver inducement systems.

Proposal to

1. clarify the fuel tank capacity restriction for mono-fuel gas vehicles (insertion of word “nominal” in definition of “mono-fuel gas vehicle”;
2. modify the Constant Volume Sampling system temperature sensor time response requirement;
3. allow the use of WLTP-based Ki and Deterioration Factors (DF) as well as On-Board Diagnostics (OBD) demos under UN R83 to permit use of WLTP methods and test results under UN R83;
4. align the definitions for bi-fuel vehicles align with the new definitions in UN GTR 15,
5. amend paragraph 5.3.1.2.4. to recognize that particulate pollutant emissions measurements are no longer limited to compression ignition vehicles;
6. introduce provisions for reagent tank specifications and limits for triggering warning and driver inducement systems.

Proposal to allow the usage of WLTP-based Ki and Deterioration Factors (DF) as well as On-Board Diagnostics (OBD) demos under UN R101. The proposal allows the use of the more robust WLTP and eases testing burdens by allowing manufacturers to use WLTP test results for UN R101.

Proposal to explicitly specify requirements related to the selection of driving modes for testing of Off-Vehicle Charging Hybrid Electric Vehicles (OVC-HEV) with a mode selection switch.

Proposal to align UN R132 with the 05 series of amendments to Regulation No. 96.

Proposal to align the Russian text with the English version.

In the absence of complete harmonization with ISO 11439, this proposal recommends that Table 6.4 of UN R110 should be amended by the following for CNG-1 designs:

1. Delete A.17, A.25, and A.7 since they do not match the tests specified in paragraph 7.5 on Cylinder design qualification tests
2. Add A.15 and A.6 since they do match the tests specified in paragraph 7.5 on Cylinder design qualification tests
3. Add A.24 because paragraph 6.9 on Fire protection requires all PRDs on all cylinder types to comply with A.24.

Proposal for a new UN Regulation on light-signalling devices, consolidating and superseding provisions of UN Regulations Nos. 4, 6, 7, 23, 38, 50, 77, 87 and 91.

Proposal to align the approval code for light sources approved according to Regulation No. 37 with the approval number as prescribed by Revision 3 of the 1958 Agreement, schedule 4. Parallel proposals have been submitted with regard to UN R99 and R128.

Proposal to align the approval code for light sources approved according to Regulation No. 99 with the approval number as prescribed by Revision 3 of the 1958 Agreement, schedule 4. Parallel proposals have been submitted with regard to UN R37 and R128.

Proposal to align the approval code for light sources approved according to Regulation No. 129 with the approval number as prescribed by Revision 3 of the 1958 Agreement, schedule 4. Parallel proposals have been submitted with regard to UN R37 and R99.

Proposal to enable approval of side-marker and position lamps with regard to switching requirements when mutually incorporated. Vehicles include designs where lamps wrap around vehicle corners. In cases where optional side-marker lamps are grouped with a position lamp that is reciprocally incorporated with the direction indicator, it should be possible to switch off the side-marker lamp (as can be done with the position lamp) in order to improve conspicuity of the direction indicator.

The proposal also defines specifications for the design and operation of external status indicators for Vehicle Alarm Systems (VAS), Alarm Systems (AS) and immobilizers under UN R48 pursuant to provisions of UN R97 and R116.

The proposal also corrects and clarifies the following:

• para. 5.7.2.1. editorial alignment of text with current terminology
• replace undefined “effective outlet” terminology with defined “apparent surface” reference
• reintroduction of missing reference to “transverse plane” in paras. 5.10.1. and 5.10.2.
• para. 6.2.9. and related subsequent paragraphs to clarify the application of the 2000 lumen criteria
• para. 6.26.9.2. to correct a cross-reference with UN R23
• measurement of the minimum height in relation to the ground for dipped beam headlamps (para. 5.8.2).

Proposal to define specifications for the design and operation of external status indicators for Vehicle Alarm Systems (VAS), Alarm Systems (AS) and immobilizers under UN R48 pursuant to provisions of UN R97 and R116.

Proposal also to address inconsistencies, clarify text, and correct terminology in Regulation No. 48:

• para. 5.7.2.1. editorial alignment of text with current terminology
• replace undefined “effective outlet” terminology with defined “apparent surface” reference
• reintroduction of missing reference to “transverse plane” in paras. 5.10.1. and 5.10.2.
• para. 6.2.9. and related subsequent paragraphs to clarify the application of the 2000 lumen criteria
• para. 6.26.9.2. to correct a cross-reference with UN R23.

Proposal to

1. remove the prohibition against lamps “reciprocally incorporated” with any other lamp, correcting an oversight from a previous amendment process, and
2. update the definition of “stop lamp” in order to allow the use of different stop lamp activation methods for powered two-wheelers as currently applicable for four-wheelers; e.g. by the application of a retarder or a similar device.

Proposal to enable the installation of Class B devices approved under UN R112 as headlamps.

Proposal to introduce the flexible pedestrian legform impactor (FlexPLI) test tool, a new bumper test area definition, and related Injury Assessment Reference Values (IARVs).

Proposal for a new UN Regulation on Road Illumination Devices (RID) to supersede UN Regulations Nos. 19, 98, 112 (thus 1, 8, and 20), 113 (thus 56, 57, 72, 76, and 82), 119, and 123.

Proposal for a new UN Regulation on retro-reflecting devices (RRD) to supersede UN Regulations Nos. 3, 27, 69, 70, and 104.

Proposal to align the Russian text with the English version.

Proposal to align the French text with the English version.

Proposal prepared by the secretariat to correct and improve the quality of the image of Figure 1a of Annex 5.

Appendix to the proposal for Amendment 2 to GTR 9 providing the rationale, justifications, and other supplemental information concerning the development of the amendment to introduce the Flex PLI lower legform impactor and related test procedures, including new bumper test area specifications.

OICA proposal to clarify that the numbering of type approvals for UN Regulations does not apply to UN Regulation No. 0 on international whole vehicle type approval. Numbering under UN R0 is explained in that Regulation.

Proposal to update the list of UN Regulations subject to UN R0 (Annex 4), including addition of UN R14 (safety belt anchorages) and UN R34 (rear impact and fire risk).

Proposal to

1. remove the prohibition against lamps “reciprocally incorporated” with any other lamp, correcting an oversight from a previous amendment process, and
2. update the definition of “stop lamp” in order to allow the use of different stop lamp activation methods for powered two-wheelers as currently applicable for four-wheelers; e.g. by the application of a retarder or a similar device.

The objective of this proposal is to develop, in the framework of the 1998 Agreement, an amendment to UN Global Technical Regulation (UN GTR) No. 6 on Safety Glazing to adapt the Regulation to technical progress by providing optional use of thinner laminated-glass panes meeting mechanical strength requirements in front, exterior, forward-facing glazing of upper deck of double decked buses instead of laminated windscreen.

Proposal to remove the prohibition against lamps “reciprocally incorporated” with any other lamp, correcting an oversight from a previous amendment process.

Proposal to remove the prohibition against lamps “reciprocally incorporated” with any other lamp, correcting an oversight from a previous amendment process.

Proposal to introduce transitional provisions for the phasing out of the existing Regulations on lighting and light-signalling in conjunction with the introduction of three new simplified Regulations on Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R4 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R6 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Revised proposal (for the March 2018 WP.29 session) to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 05 series of Regulation No. 48.

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R50 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R69 in conjunction with the introduction of the new UN Regulation on Retro-Reflecting Devices (RRD).

Proposal for a new UN Regulation on Road Illumination Devices (RID) to supersede UN Regulations Nos. 19, 98, 112 (thus 1, 8, and 20), 113 (thus 56, 57, 72, 76, and 82), 119, and 123.

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R7 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R19 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R23 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R27 in conjunction with the introduction of the new UN Regulation on Retro-Reflecting Devices (RRD).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R38 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Proposal (submitted for the March 2019 WP.29 session) to introduce references to the three new simplified lighting Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 06 series of Regulation No. 48.

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R70 in conjunction with the introduction of the new UN Regulation on Retro-Reflecting Devices (RRD).

Updated proposal (for consideration during the March 2019 WP.29 session) to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 01 series of Regulation No. 74.

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R77 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R87 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R91 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R98 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R104 in conjunction with the introduction of the new UN Regulation on Retro-Reflecting Devices (RRD).

Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R112 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Revised proposal from GRE (submitted to the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R113 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R119 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Proposal from GRE to introduce transitional provisions for the phasing out of UN R123 in conjunction with the introduction of the new UN Regulation on Road Illumination Devices (RID).

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 02 series of Regulation No. 53.

Proposal to introduce references to the three new simplified Regulations (Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD)) into the 01 series of Regulation No. 86.