Revised proposal from GRE (for the March 2019 WP.29 session) to introduce transitional provisions for the phasing out of UN R77 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Proposed transitional provisions to end further development of current UN lighting regulations in favor of the new UN Regulations on light-signalling devices (LSD), road illumination devices (RID), and retro-reflecting devices (RRD) developed under the Simplification of Lighting Regulations (SLR) program.

Request to GRE and the SLR informal group to give consideration to transitional provisions.

SLR informal group removing the brackets around (i.e., confirming) the 24-month transition period for the switch to approvals only under the new LSD, RRD, and RID regulations and to delete the proposal that approvals and extensions of approvals granted under each regulation would remain valid indefinitely.

Proposal from GRE to introduce transitional provisions for the phasing out of UN R77 in conjunction with the introduction of the new UN Regulation on Light-Signaling Devices (LSD).

Proposal to improve the document GRE/2018/11 (GRE-79-31) and to introduce in R48-06 new minimum installation requirements for type approved lighting and light-signalling devices and to improve the transitional provisions for Regulations Nos. 3, 4, 6, 7, 19, 23, 27, 38, 50, 69, 70, 77, 87, 91, 98, 104, 112, 113, 119 and 123. Proposal for new minimum installation requirements for type approved lighting and light-signalling devices in R48-06. Proposal to clarify which devices may be installed on the vehicles in line with the applicable requirements as amended by the new UN Regulations on light-signalling devices, road illumination devices, and retro-reflecting devices.

Proposal to a) improve the transitional provisions presented in GRE/2018/11 with regard to the collective
amendments to Regulations Nos. 3, 4, 6, 7, 19, 23, 27, 38, 50, 69, 70, 77, 87, 91, 98, 104, 112, 113, 119 and 123 and b) introduce new requirements into the 06 series of amendments to UN R48 with regard to the validity and installation of type approved lighting and light-signalling devices.

Proposal from the Simplification of Lighting Regulations informal group to introduce transitional provisions for the phasing out of the existing Regulations on lighting and light-signalling in conjunction with the introduction of three new simplified Regulations on Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD).

Proposal from the Simplification of Lighting Regulations informal group to introduce transitional provisions for the phasing out of the existing Regulations on lighting and light-signalling in conjunction with the introduction of three new simplified Regulations on Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD).

Proposal from the Simplification of Lighting Regulations informal group to combine provisions of UN Regulations Nos. 4, 6, 7, 23, 38, 50, 77, 87 and 91 into a single regulation. This consolidation aims to streamline the administration and implementation of these lighting regulations while setting the foundation for a future shift towards performance-based approval requirements. This proposal restructures the existing body of lighting regulations without changing their content (e.g., technical requirements).

Proposal as sent by the SLR informal group to GRE for its October 2017 session for transitional provisions for the phasing out of the current lighting regulations (in terms of continued development and granting of new type approvals) in favor of the new lighting device and related regulations.

Proposal to clarify the requirements for light sources in the lighting and light-signalling Regulations listed in Annex 4 to Regulation No. 0 on the International Whole Vehicle Type Approval (IWVTA).

Collective amendment working draft to introduce the transitional provisions for the switch from the current lighting regulations to the new simplified lighting regulations (light-signalling, retro-reflective devices, and road illumination devices). The draft proposal would allow 24 months from the entry into effect of the new regulations.

Revised proposal to clarify the requirements for light sources in the lighting and light-signalling Regulations listed in Annex 4 to Regulation No. 0 on the International Whole Vehicle Type Approval (IWVTA) pursuant to GRE-77 discussions.

Proposal to clarify the requirements for light sources in the lighting and light-signalling Regulations listed in Annex 4 to Regulation No. 0 on the International Whole Vehicle Type Approval (IWVTA).

Proposals for amendments to Regulations Nos. 4, 6, 7, 19, 23, 38, 48, 50, 77, 87, 91, 98, 112, 113, 119, 123 to clarify requirements for light sources in lighting and light-signalling Regulations listed in Annex 4 to UN Regulation No. 0. The proposed UN R0 on whole vehicle type approval requires submission of approval certificates for components and systems. Vehicle manufacturers work directly with UN R48 approvals, but lamp and device approvals are generally handled by lighting suppliers. UN R48 includes provisions for listing approvals of lighting units, but not for approvals of light sources (presently UN R37, R99, and R128). This set of proposed amendments introduces provisions for light-source approvals under the device regulations.

Proposal to

1. insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources,
2. update the Conformity of Production (CoP) requirements,
3. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
4. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
5. introduce editorial improvements to the requirements for markings,
6. remove the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s),
7. refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources.

Revised proposal (removing the section on UN R48 and incorporating corrections noted in document GRE-76-07) to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required. This collective amendment addresses Regulations Nos. 7, 23, 38, 77, 91 and 119. The proposals concerning UN R48 will be resubmitted for consideration during the 77th GRE session.

Correction to the proposal for a collective amendment to Regulations Nos. 7, 23, 38, 48, 77, 91 and 119. Since the cornering lamp projects a beam to the left and right of the reference axis, it is not relevant to check the photometric values in the reference axis (HV). Therefore, the test point at 2.5°D, 45°L or R shall be used.

The current requirements on light source failure in lamps equipped with multiple light sources differ across UN Regulations. GTB submitted and then withdrew a proposal to align these requirements (GRE/2016/13). This updated proposal improves upon the text of the previous proposal to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required.

This proposal removes the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s). From an electronic point of view, the information of the wattage brings no benefit and is confusing if the same module is used in different systems and at different wattages.

Compressed data package of three documents providing lists of proposals for amendments to lighting regulations within the context of plans for the restructuring of UN lighting regulations.

Proposal to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required.

This proposal concerns lamps equipped with several light sources and fitted with an operating tell-tale that indicates the failure of any one of these light sources. The current provisions for the failure of one light source (the “N-1” requirement) are difficult to apply as a complete photometric check for all possible combinations of light source failure is required. The revised text follows the approach of supplement 17 to Regulation No. 87 and removes the requirement to check the complete photometric requirement, in case of failure of any light source, when the lamp is fitted on the vehicle with an operating tell-tale.

Revision of the regulation on parking lamps pursuant to the proposal to simplify the UN lighting regulations.

Proposal to reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86 into the Regulations 3, 4, 6, 7, 19, 23, 38, 50, 77, 87, 91, 98, 104, 112, 113, 119 and 123. This proposal is a revised version of document GRE/2013/55 discussed during the October 2013 GRE session.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definition of “type”, with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings.

Although documents GRE/2013/45 and GRE-70-02 were adopted by GRE at its last (70th) session, this proposal consolidates the amendments and offers editorial improvements to the provisions concerning markings in Regulations Nos. 19, 23, 38, 65 and 119. These editorial improvements aim to clarify that the devices, and not only the samples, shall bear the trade name or mark and align the requirements with the other correctly worded regulations to avoid misunderstanding.

In a letter to Mssrs. Gauvin and Ramos, the European Commission, pursuant to concerns raised in its Technical Committee Motor Vehicles, raises issues with two paragraphs that are reproduced in a number of GRE proposals set for consideration at the November WP.29. The EU, therefore, cannot vote to adopt the proposals until these concerns have been addressed (i.e., for the March 2014 session).

Revisions to the GRE proposal (document WP.29/2013/69) to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production requirements (CoP). This proposal also applies to documents:
WP.29/2013/71,
WP.29/2013/72,
WP.29/2013/76,
WP.29/2013/79,
WP.29/2013/83,
WP.29/2013/87,
WP.29/2013/88,
WP.29/2013/89 and
WP.29/2013/94.

UK proposal to address concerns raised in the series of proposals to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources.

The European Commission, pursuant to concerns raised in its Technical Committee Motor Vehicles, raises issues with two paragraphs that are reproduced in a number of GRE proposals set for consideration at the November WP.29. The EU, therefore, cannot vote to adopt the proposals until these concerns have been addressed (i.e., for the March 2014 session).

Proposal to revise the Italian proposal in order to clarify that the requirements pertain only to characteristics verifiable directly on each lamp in order to avoid confusion with characteristics that can only be verified on the vehicle after installation.

Editorial correction to the presentation of the collective amendments to selected lighting regulations proposed in document GRE/2013/55.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources, and to update the Conformity of Production (CoP) requirements.

Proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks.

Proposal to reference the requirements for installation contained in Regulations Nos. 48, 53, 72 and 86 into the Regulations 3, 4, 6, 7, 19, 23, 38, 50, 77, 87, 91, 98, 104, 112, 113, 119 and 123.

Clarifications to the proposal by Germany proposing to update the Conformity of Production requirements (CoP).

Italy proposes to introduce into each Regulation dealing with the type approval of lighting or light signalling devices a direct reference to the requirements contained in Regulations 48, 53 and 74, and 86, mandating the lamp manufacturers to apply them to obtain type approvals.

Submitted by Germany proposing to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources. This proposal supersedes document GRE/2012/20 and informal document GRE-68-03.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Text as adopted by the Working Party on Lighting and Light Signalling (GRE) at its 68th session to amend the geometric visibility provisions.

This document contains editorial corrections to document GRE/2012/42 to amend the geometric visibility provisions of Regulations No. 3, 6, 7, 48, 77 and 91 following a review with the GRE secretariat to ensure that the proposal aligns with the latest state of the regulations.

GRE/2012/42 is a GTB proposal to amend the geometric visibility provisions. This document corrects GRE/2012/42 in line with the latest state of the subject regulations including amendments submitted for consideration at the November WP.29 session.

Document GRE-68-02 from the Working Party “Brussels 1952” (GTB) proposes to amend the geometric visibility provisions of multiple lighting regulations. Since manufacturers have already developed lighting in line with the current definitions, OICA seeks a 48-month transition period.

Proposed modifications to the German proposal (GRE/2012/20) to ensure that non-replaceable and unapproved filament light sources used in sealed devices and in (filament) light-source modules have a sufficient lifetime and fulfill color endurance verification.

Proposal from Germany to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources.

GTB proposal to amend the geometric visibility provisions. Subsequent to the preparation of the proposed amendments in document GRE/2012/42, several editorial corrections have been identified by GTB experts. This document replaces that original submission.

Proposal from the Working Party “Brussels 1952” (GTB) to amend the geometric visibility provisions.

Proposal as adopted by the Working Party on Lighting and Light-Signalling (GRE) at its sixty-seventh session to introduce provisions for the use of light-emitting diode (LED) light sources according to the draft Regulation No. 127 (documents WP.29/2010/44 and Corr.1).

The Forum adopted a new UN Regulation on LED light sources at its March 2012 session. This document updates the collective amendment that introduces LED light sources into the relevant UN Regulations 4, 6, 7, 23, 38, 50, 77, 87, 91 and 119.

Proposal to clarify the definitions of type with regard to manufacturer, trade names and marks.

Proposal to complete the requirements regarding the use of cap–holder systems in the case of light source modules in a lamp.