Proposal to add a reference to the installation parameters of the licence plate illumination lamps determined during their type approval process. Every type-approved device or pair of devices have their own geometrical position in relation to the rear registration plate which is determined based on the illumination levels, maximum gradient value, angles of visibility and light incidence angle. This proposal would introduce a reference to these parameters in UN R48.

Proposal from GRE to introduce transitional provisions for the phasing out of UN R4 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Proposed transitional provisions to end further development of current UN lighting regulations in favor of the new UN Regulations on light-signalling devices (LSD), road illumination devices (RID), and retro-reflecting devices (RRD) developed under the Simplification of Lighting Regulations (SLR) program.

Request to GRE and the SLR informal group to give consideration to transitional provisions.

SLR informal group removing the brackets around (i.e., confirming) the 24-month transition period for the switch to approvals only under the new LSD, RRD, and RID regulations and to delete the proposal that approvals and extensions of approvals granted under each regulation would remain valid indefinitely.

Proposal from GRE to introduce transitional provisions for the phasing out of UN R4 in conjunction with the introduction of the new UN Regulation on Light-Signalling Devices (LSD).

Proposal to improve the document GRE/2018/11 (GRE-79-31) and to introduce in R48-06 new minimum installation requirements for type approved lighting and light-signalling devices and to improve the transitional provisions for Regulations Nos. 3, 4, 6, 7, 19, 23, 27, 38, 50, 69, 70, 77, 87, 91, 98, 104, 112, 113, 119 and 123. Proposal for new minimum installation requirements for type approved lighting and light-signalling devices in R48-06. Proposal to clarify which devices may be installed on the vehicles in line with the applicable requirements as amended by the new UN Regulations on light-signalling devices, road illumination devices, and retro-reflecting devices.

Proposal to a) improve the transitional provisions presented in GRE/2018/11 with regard to the collective
amendments to Regulations Nos. 3, 4, 6, 7, 19, 23, 27, 38, 50, 69, 70, 77, 87, 91, 98, 104, 112, 113, 119 and 123 and b) introduce new requirements into the 06 series of amendments to UN R48 with regard to the validity and installation of type approved lighting and light-signalling devices.

Proposal from the Simplification of Lighting Regulations informal group to introduce transitional provisions for the phasing out of the existing Regulations on lighting and light-signalling in conjunction with the introduction of three new simplified Regulations on Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD).

Proposal from the Simplification of Lighting Regulations informal group to combine provisions of UN Regulations Nos. 4, 6, 7, 23, 38, 50, 77, 87 and 91 into a single regulation. This consolidation aims to streamline the administration and implementation of these lighting regulations while setting the foundation for a future shift towards performance-based approval requirements. This proposal restructures the existing body of lighting regulations without changing their content (e.g., technical requirements).

Proposal from the Simplification of Lighting Regulations informal group to introduce transitional provisions for the phasing out of the existing Regulations on lighting and light-signalling in conjunction with the introduction of three new simplified Regulations on Light-Signalling Devices (LSD), Road Illumination Devices (RID) and Retro-Reflective Devices (RRD).

Proposal as sent by the SLR informal group to GRE for its October 2017 session for transitional provisions for the phasing out of the current lighting regulations (in terms of continued development and granting of new type approvals) in favor of the new lighting device and related regulations.

Proposal to clarify the requirements for light sources in the lighting and light-signalling Regulations listed in Annex 4 to Regulation No. 0 on the International Whole Vehicle Type Approval (IWVTA). The reference to “Illumination of rear registration plate lamps” should read ""Illumination of rear registration plates".

Collective amendment working draft to introduce the transitional provisions for the switch from the current lighting regulations to the new simplified lighting regulations (light-signalling, retro-reflective devices, and road illumination devices). The draft proposal would allow 24 months from the entry into effect of the new regulations.

Revised proposal to clarify the requirements for light sources in the lighting and light-signalling Regulations listed in Annex 4 to Regulation No. 0 on the International Whole Vehicle Type Approval (IWVTA) pursuant to GRE-77 discussions.

Proposal to clarify the requirements for light sources in the lighting and light-signalling Regulations listed in Annex 4 to Regulation No. 0 on the International Whole Vehicle Type Approval (IWVTA).

Proposals for amendments to Regulations Nos. 4, 6, 7, 19, 23, 38, 48, 50, 77, 87, 91, 98, 112, 113, 119, 123 to clarify requirements for light sources in lighting and light-signalling Regulations listed in Annex 4 to UN Regulation No. 0. The proposed UN R0 on whole vehicle type approval requires submission of approval certificates for components and systems. Vehicle manufacturers work directly with UN R48 approvals, but lamp and device approvals are generally handled by lighting suppliers. UN R48 includes provisions for listing approvals of lighting units, but not for approvals of light sources (presently UN R37, R99, and R128). This set of proposed amendments introduces provisions for light-source approvals under the device regulations.

Proposal to

1. insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources,
2. update the Conformity of Production requirements (CoP),
3. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86 for application as warranted
4. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
5. introduce editorial improvements to the requirements for markings,
6. remove the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s).

Advances in LED lighting raise the prospects for incorporation of lighting into rear registration plates. In 2004, in response to a proposal for the regulation of such plates under UN R48, GRE determined that illuminated plates were not lamps and therefore were outside the scope of UN R48. The Spanish delegation would like to submit this issue again for the consideration of GRE members in order to have a coordinated and common view on this subject.

This proposal removes the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s). From an electronic point of view, the information of the wattage brings no benefit and is confusing if the same module is used in different systems and at different wattages.

Compressed data package of three documents providing lists of proposals for amendments to lighting regulations within the context of plans for the restructuring of UN lighting regulations.

Updated paper on the grouping of lighting regulations under one of three new regulations as follows:
Light Signaling Devices incorporating Regulations 4, 6, 7, 23, 38, 50, 77, 87, and 91
Forward Lighting Devices incorporating Regulations 19, 98, 112, [ 113 ], 119, and 123
Retro-Reflective Devices incorporating Regulations 3, 27, 69, 70, and 104

Proposal for a revision of UN R4 under the proposed simplification of lighting regulations.

Proposal to introduce provisions for registration plates that differ in size from the standard EU plates. Please note that the designation as Supplement 18 is an error. This proposal will be adopted as Supplement 17.

Proposal to reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86 into the Regulations 3, 4, 6, 7, 19, 23, 38, 50, 77, 87, 91, 98, 104, 112, 113, 119 and 123. This proposal is a revised version of document GRE/2013/55 discussed during the October 2013 GRE session.

Text prepared by Japan and Finland to introduce provisions for registration plates that differ in size from the standard EU plates.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definition of “type”, with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings.

Although documents GRE/2013/45 and GRE-70-02 were adopted by GRE at its last (70th) session, this proposal consolidates the amendments and offers editorial improvements to the provisions concerning markings in Regulations Nos. 19, 23, 38, 65 and 119. These editorial improvements aim to clarify that the devices, and not only the samples, shall bear the trade name or mark and align the requirements with the other correctly worded regulations to avoid misunderstanding.

In a letter to Mssrs. Gauvin and Ramos, the European Commission, pursuant to concerns raised in its Technical Committee Motor Vehicles, raises issues with two paragraphs that are reproduced in a number of GRE proposals set for consideration at the November WP.29. The EU, therefore, cannot vote to adopt the proposals until these concerns have been addressed (i.e., for the March 2014 session).

Revisions to the GRE proposal (document WP.29/2013/69) to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production requirements (CoP). This proposal also applies to documents:
WP.29/2013/71,
WP.29/2013/72,
WP.29/2013/76,
WP.29/2013/79,
WP.29/2013/83,
WP.29/2013/87,
WP.29/2013/88,
WP.29/2013/89 and
WP.29/2013/94.

UK proposal to address concerns raised in the series of proposals to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources.

As part of the work on establishing an International Whole Vehicle Type Approval (IWVTA) system, Japan has noted differences between European and Japanese vehicle registration (license) plates. Since UN R4 would be part of the IWVTA process, Japan seeks to add its plate requirements to the European requirements embodied in UN R4 in order to enable Japan to adopt this regulation and thereby adhere to the IWVTA.

Proposal to add registration plates used in non-European Contracting Parties to the scope of the regulation. This document is based on the previous document GRE-69-23.

The European Commission, pursuant to concerns raised in its Technical Committee Motor Vehicles, raises issues with two paragraphs that are reproduced in a number of GRE proposals set for consideration at the November WP.29. The EU, therefore, cannot vote to adopt the proposals until these concerns have been addressed (i.e., for the March 2014 session).

Proposal to revise the Italian proposal in order to clarify that the requirements pertain only to characteristics verifiable directly on each lamp in order to avoid confusion with characteristics that can only be verified on the vehicle after installation.

Editorial correction to the presentation of the collective amendments to selected lighting regulations proposed in document GRE/2013/55.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production requirements (CoP).

Proposal to reference the requirements for installation contained in Regulations Nos. 48, 53, 72 and 86 into the Regulations 3, 4, 6, 7, 19, 23, 38, 50, 77, 87, 91, 98, 104, 112, 113, 119 and 123.

Proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks.

UN R4 specifies requirements regarding registration plates that are used primarily in Europe. Japan proposes to include additional provisions in order to extend the applicability of the regulation to registration plates of different sizes used in non-European countries. This presentation supplements the proposal.

UN R4 specifies requirements regarding registration plates that are used primarily in Europe. Japan proposes to include additional provisions in order to extend the applicability of the regulation to registration plates of different sizes used in non-European countries. Japan also proposes creating Class A and Class B lamp categories towards this end.

Italy proposes to introduce into each Regulation dealing with the type approval of lighting or light signalling devices a direct reference to the requirements contained in Regulations 48, 53 and 74, and 86, mandating the lamp manufacturers to apply them to obtain type approvals.

Submitted by Germany proposing to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources. This proposal supersedes document GRE/2012/20 and informal document GRE-68-03.

Submitted by Germany proposing to update the Conformity of Production requirements (CoP).

Japanese perspectives on selected regulations (NU R4, 34, 46, and 79) within the context of adoption of the International Whole Vehicle Type Approval system/regulation.

Proposed modifications to the German proposal (GRE/2012/20) to ensure that non-replaceable and unapproved filament light sources used in sealed devices and in (filament) light-source modules have a sufficient lifetime and fulfill color endurance verification.

Proposal from Germany to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources.

Proposal as adopted by the Working Party on Lighting and Light-Signalling (GRE) at its sixty-seventh session to introduce provisions for replaceable light-emitting diode (LED) light sources and to correct and harmonize the provisions concerning approval markings.

The Forum adopted a new UN Regulation on LED light sources at its March 2012 session. This document updates the collective amendment that introduces LED light sources into the relevant UN Regulations 4, 6, 7, 23, 38, 50, 77, 87, 91 and 119.

This proposal mainly corrects an unintended, but potentially costly, obligatory (rather than optional) use of mingled letters in the marking provisions of UN R23. The proposal also corrects the marking provisions of UN R4 and R23 by deleting an unnecessary hyphen.

Proposal to clarify the definitions of type with regard to manufacturer, trade names and marks.

Proposal to prohibit the use of light source modules with ECE cap–holder systems.

Proposal to complete the requirements regarding the use of cap–holder systems in the case of light source modules in a lamp.

Proposal to insert provisions to cover cases where several non-identical light source modules are used in a lamp.

Proposal to insert references to Regulations Nos. 37 and 99 and to the International Electrotechnical Commission (IEC) Publication 60061, specifying the use of filament lamps and gas-discharge light sources.

Proposal to correct the definition for different types of rear registration plate lamps. This proposal deletes the criteria " the angle of incidence of the light on the surface of the plate" in paragraph 1.3 because this item contradicts the provisions of paragraphs 2 and 7 which state "…. the manufacturer of the illuminating device shall specify one or more or a field of positions in which the device is to be fitted in relation to the space for the registration plate …. ".

Proposal to clarify the scope of the regulation specifically to vehicles of categories M, N, O, and T.

Lamps equipped with non-replaceable light sources, e.g. LED’s, can be operated at a range of voltages. This proposal enables the proper testing and approval of such devices under a single approval number provided that the range of voltage and the rated (maximum) wattage is included in the marking of the lamp.

Proposal to allow the use of changeable “light source modules” instead of non-replaceable light sources (pursuant to the amendments previously agreed for UN R7).

Proposal to introduce provisions for the approval of "slightly curved registration plates”.