Proposal to expand the scope of the regulation on unauthorized L-category vehicle use to include electronic devices such as keyless entry systems, similarly to what already exists in UN R116 on passenger car use.

Proposal to introduce requirements for CNG compressor and CNG accumulator components designed to maintain stable pressure in fuel systems. See also documents GRSG-113-24 and 25 from the previous GRSG session.

Proposal to clarify the text of document GRSG/2018/7 submitted to enable the approval of the laminated-glass panes with improved mechanical properties, especially as designed for front, exterior, forward-facing glazing of the upper deck of a double-deck vehicle. The proposal would amend Annex 7 (laminated-glass panes), inserting a new paragraph 6. to allow optional 2,260 g ball test and headform test for laminated-glass panes.

Proposal to align Annex 11 with Annex 3 following the removal of paragraphs in the latter regarding the marking of a vehicle with respect to the mass of baggage (done via Corrigendum 1 to Revision 6). This proposal would delete the same requirements (paragraphs 3.3.1.2.1, 3.3.1.2.2., 3.3.1.2.2.1. and 3.3.1.2.2.2) from Annex 11.

Proposal to allow the use of a generator fueled by the vehicle gaseous fuel system that provides electricity to run accessories (e.g., overnight power in sleeper cabs, to maintain battery charge during high electrical power use with loading or lifting equipment). This proposal would allow for the use of LNG/CNG from vehicle fuel tanks and thereby reduce the potential need to vent gas into the air in response to pressure buildup due to warming over time by using the gas to power other devices and equipment.

Italy research on type CNG4 cylinders in support of the proposal to require that covers be removed in cases where ogive protective covers are fitted to a cylinder before conducting the impact damage (drop) test (document GRSG/2017/29).

The target of the meeting was to define essential periodic inspection requirements to be respected when installing gaseous fuel components into a vehicle, and to clarify the material requirements for components inside the LPG tank. The work addressed UN R67 and UN R110. No further meetings are planned at this time.

Proposal developed by the Gas-fueled Vehicle Regulations Task Force to facilitate periodic inspections of gas containers through better visibility. In addition, Germany suggests adding that paragraph to allow a Contracting Party or a regional organization of Contacting Parties like the EU to refuse national or regional type-approval and to refuse first registration of a vehicle type affected by the changes introduced by the 02 series of amendments but not meeting those stipulations. Paragraph 22.13 is an addition to paragraph 22.9. giving more stress to aspects of national and regional type-approval and of first registration of vehicles.

Proposal developed by the Gas-fueled Vehicle Regulations Task Force to facilitate periodic inspections of gas containers through better visibility. In addition, Germany suggests adding a paragraph to allow a Contracting Party or a regional organization of Contacting Parties like the EU to refuse national or regional type-approval and to refuse first registration of a vehicle type affected by the changes introduced by the 03 series of amendments but not meeting those stipulations. Paragraph 24.22. is an addition to paragraph 22.18. giving more stress to the aspects of national and regional type-approval and of first registration of vehicles.

Report on the task force sessions held to discuss the potential for improvements in the safety of M₂ and M₃ vehicles in the event of fire.

Draft Terms of Reference and Rules of Procedure of the GRSG informal working group on the behaviour of M2 and M3 general construction in case of fire event (BMFE) pursuant to discussions held since the last GRSG session.

Proposal to enable to approval of vehicles equipped with mechanisms other than platforms intended to assist access by persons with reduced mobility. The purpose is to avoid hindering innovation in offering solutions to persons with reduced mobility. The proposal add “lift” to the examples of possible mechanisms and modifies the language to be less specific in references to “wheelchairs” to address persons with reduced mobility regardless of whether they use a wheelchair.

Proposal to correct the Russian text of the regulation.

Proposal to correct the Russian text of the regulation.

Proposal to allow for the removal of non-structural parts and accessories in fulfilling the accessibility/inspection provisions of UN R110.

Proposal to amend GRSG/2018/7 by adding the marking “/D” to signify laminated-glass panes subjected to the 2,260 g ball test and the headform test.

Draft regulation proposed by the VRU-Proxi informal working group.

Proposal as finalized during the April 2018 GRSG session to amend Annex 7 (laminated-glass panes), inserting a new paragraph 6 to allow optional 2,260 g ball test and headform test for laminated-glass panes. The proposal adds the marking “/D” to signify laminated-glass panes subjected to the 2,260 g ball test and the headform test. The proposal aims to enable the approval of laminated-glass panes with improved mechanical properties, especially as designed for front, exterior, forward-facing glazing of the upper deck of a double-deck vehicle.

OICA comments on document GRSG-114-12.

Proposal to correct the draft text to align with the latest version of UN R46. GRSG/2018/4 aims to clarify the circumstances under which the provision of information through overlays is permissible.

Proposal to delete the reference to visual inspection under the support straps of the cylinders from the text under consideration. Such inspection would require dismantling of the cylinder installations which would contravene the consensus decision to avoid such exhaustive dismantling.

Proposal to amend and clarify the need for a gas flow adjuster under UN R110 with regard to the use of carburetors and fuel injectors. A gas flow adjuster is not necessary when an electronic fuel injection system manages the air/fuel mixture and therefore should be removed from paragraph 18.3.1. An adjuster is needed when air/fuel mixture runs via a carburetor and therefore should be added to paragraph 18.3.2.

Proposal to separate requirements for vehicle immobilizers into a new UN Regulation (from UN R116) in order to facilitate the inclusion of anti-theft regulations in UN R0 on whole vehicle type approvals.

Proposal to clarify that anti-theft-related vehicle components such as keys are not subject to the environmental tests (section 6.4.) of UN R116 which were established for components embedded in the vehicle.

Proposal to remove references to European radio frequency standards (paragraphs 6.2.3., 7.2.3. and 8.2.2.). Telecommunications devices must meet requirements specific to local markets. Therefore, the references to standards specific to European markets (but not other markets) fall outside the purview of UN Regulations.

Proposal to align UN R105 with provisions adopted by the Working Party on the Transport of Dangerous Goods (WP.15) under the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR), edition 2019.

Proposal to align the Communication forms with regard to the separation of approval numbers and extension numbers with the provisions of Revision 3 of the 1958 Agreement (E/ECE/TRANS/505/Rev.3) Schedule 4.

Proposal to confirm that M₁ vehicles not fitted with a side airbag are outside the scope of UN R144.

Proposal from the GRSG secretariat to correct the “model B” figure illustrating marking provisions with a reference to the 03 series of amendments to UN R31.

Discussion paper proposing an effort to develop safety requirements for the protection of the driver and
tourist guide situation at the front of motor coaches.

Proposal for clarifications and editorial improvements to the draft amendment to require, in instances where that ogive covers be removed before conducting the impact damage (drop) test.

Progress report on the effort to improve the behaviour of M₂ and M₃ general construction of buses in case of fire events.

Proposal to add a drawing and text to clarify which requirements apply to which parts of the windscreen wiper.

Proposal to delete the reference to abrasion requirements in Annex 3, paragraph 6.4.1.3. since abrasion resistance is not relevant in the assessment of resistance to weathering.

Revised version of document GRSG/2018/24 as adopted by GRSG during its 115th session.

Proposal to clarify the treatment of extensions of existing approvals under the new transitional provision guidelines (“Until 31 December 2019, Supplement 5 and Supplement 7 to the 01 series of amendments to this Regulation may not apply to extensions of approvals that were originally granted prior to the entry into force of Supplement 5 and Supplement 7.”)

Proposal to enable application of the designation “twinned wheels” across all Category L vehicles.

Password protected file: ISO/CD 19206-4: Road vehicles — Test devices for target vehicles, vulnerable road users and other objects, for assessment of active safety functions — Part 4: Requirements for bicyclist targets. The proposed new UN Regulation on Blind Spot Information Systems refers to this standard presently under development within ISO. The GRSG secretariat controls access to the working party participants.

Proposal to add a new symbol (as defined by IEC standard 60417-5009) for power on/off controls in electrified vehicles (e.g., electric or fuel cell vehicles).

Proposal to amend the transitional provisions in order to extend the use of the 06 and 07 series beyond 2022 for vehicles not affected by the 08 series of amendments (i.e., new interior fitting visual contrast requirements).