Correction to the proposal for a collective amendment to Regulations Nos. 7, 23, 38, 48, 77, 91 and 119. Since the cornering lamp projects a beam to the left and right of the reference axis, it is not relevant to check the photometric values in the reference axis (HV). Therefore, the test point at 2.5°D, 45°L or R shall be used.

The justification for changes to sub-paragraphs 5.6.(e) of Regulation No. 6 and 6.8.(e) of Regulation No. 50 is missing from document GRE/2016/20. The Task Force on Sequential Activation of direction indicators wishes to note that the paragraphs were proposed by GTB and accepted by the Task Force to clarify the text without changing the current technical requirements.

Exchange of communications between the secretariat and the UN Office of Legal Affairs concerning the simplification of lighting and light-signalling Regulations (SLR). GRE proposed to consolidate around 30 Regulations on different individual lighting and light-signalling devices (lamps) into three new Regulations (forward lighting, light-signalling, and retro-reflective devices). OLA provides general comments in response to GRE questions intended to ensure that the selected approach respects the legal and administrative requirements of UN treaties and specifically the 1958 Agreement.

Advances in LED lighting raise the prospects for incorporation of lighting into rear registration plates. In 2004, in response to a proposal for the regulation of such plates under UN R48, GRE determined that illuminated plates were not lamps and therefore were outside the scope of UN R48. The Spanish delegation would like to submit this issue again for the consideration of GRE members in order to have a coordinated and common view on this subject.

The collective amendment presented in GRE/2016/34 extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123. The introduction of LED light source categories under UN R128 for forward lighting applications (front fog, low beam, high beam,
AFS) is planned for 2017. This presentation explains the plans, timeline, and dependencies GTB proposes to address through the collective amendment, especially within the context of the simplification of lighting regulations program.

Revised proposal (removing the section on UN R48 and incorporating corrections noted in document GRE-76-07) to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required. This collective amendment addresses Regulations Nos. 7, 23, 38, 77, 91 and 119. The proposals concerning UN R48 will be resubmitted for consideration during the 77th GRE session.

Presentation concerning the proposal to introduce a new optional “Class B1” headlamp.

Proposal to reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86 into the Regulations 3, 4, 6, 7, 19, 23, 38, 50, 77, 87, 91, 98, 104, 112, 113, 119 and 123. This proposal is a revised version of document GRE/2013/55 discussed during the October 2013 GRE session.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definition of “type”, with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings.

Although documents GRE/2013/45 and GRE-70-02 were adopted by GRE at its last (70th) session, this proposal consolidates the amendments and offers editorial improvements to the provisions concerning markings in Regulations Nos. 19, 23, 38, 65 and 119. These editorial improvements aim to clarify that the devices, and not only the samples, shall bear the trade name or mark and align the requirements with the other correctly worded regulations to avoid misunderstanding.

Proposal to correct an error in Supplement 24 to the 01 series of amendments (document WP.29/2013/14 adopted by the Forum during its March 2013 session). During the compilation of the collective amendment (GRE-68-02-Rev.2), necessary changes to Regulation No. 6 were overlooked. This amendment proposes to align the treatment of categories 1, 1a and 1b with other categories and devices.

Correction of errors found in the references to “left-hand traffic” and “right-hand traffic” in the text and associated diagrams of Annex 2 of the regulation.

Proposal to correct an inconsistency between the regulation text and Figure B of Annex 3.

Proposal to align the text in the header row of the table in paragraph 6.1 (light emitted by the lamps) with the definitions used in Regulation No. 48 for the installation of “single lamps”, “lamps marked D” and “interdependent lamps”.

Proposal to amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45 where the specified quantity of “2 ± 1 parts by weight” of surfactant results in invalid testing. The correct specification should be “2 ± 1 drops” of surfactant. While GTB notes that the specification should eventually be incorporated differently under the pending simplification of lighting regulations, the organization strongly urges amending UN R45 as quickly as possible.

Proposal to correct the terminology in paragraph 5.7.2.1. for consistency across all requirements and to clarify the language in paragraphs 6.2.9., 6.3.6.1.2.1. and 6.3.6.1.2.2. to promote the correct application of the 2,000-lumen limit.

Supplement 3 to the 01 series of amendments to UN R 98, 112, and 123 deleted the measurement point HV from the photometric requirement table. The HV measurement point, however, remains a requirement for checking photometric stability. This proposal removes the HV measurement point from the photometric stability requirements for the passing beam. The HV measurement point remains a valid for the driving beam.

This proposal removes the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s). From an electronic point of view, the information of the wattage brings no benefit and is confusing if the same module is used in different systems and at different wattages.

The current requirements on light source failure in lamps equipped with multiple light sources differ across UN Regulations. GTB submitted and then withdrew a proposal to align these requirements (GRE/2016/13). This updated proposal improves upon the text of the previous proposal to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required.

This collective amendment on the stability of photometric performance during the heat test, with particular reference to the movement of the cut-off line, clarifies the test cycle and also aligns the requirements of Regulations Nos. 19, 98, 112, 113 and 123. In addition to resolving problems of interpretation presented by the current text, this collective amendment will assist the Informal Working Group “Simplification of Lighting and Light-Signalling Regulations” in drafting the new simplified Regulations which is underway.

This collective amendment extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123 (as presented in the previous session document GRE-75-14). The proposal would allow for the use of regulated replaceable LED light sources according to Regulation No. 128 in all applications where the use of LED modules is already permitted.

Proposal to update the Conformity of Production provisions.

GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production requirements (CoP).

GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production requirements (CoP).

GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.

Proposal to complete the deletion of distributed lighting systems (DLS), or rather light generators, from the regulation and to update the Conformity of Production (CoP) requirements

GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.

GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.

Proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources.

GRE proposal to update the Conformity of Production (CoP) requirements.

GRE proposal to update the Conformity of Production (CoP) requirements.

GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources, and to update the Conformity of Production (CoP) requirements.

GRE proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.

Proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.

Proposal to amend the provisions concerning the heat test requirements for Conformity of Production (CoP), to complete the deletion of distributed lighting systems (DLS) (light generators) from the regulations, and to update the general CoP requirements.

Proposal to amend the provisions concerning the heat test requirements for Conformity of Production and to otherwise update the CoP requirements.

Proposal to update the Conformity of Production (CoP) requirements and to correct provisions on bend lighting for motorcycles recently adopted by WP.29 as Supplement 2 (document WP.29/2012/83).

Proposal to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources and to update the Conformity of Production (CoP) requirements.

Proposal to clarify the Conformity of Production requirements.

Proposal to clarify the Conformity of Production requirements.