Proposal is to align GTR 16 with technical progress, incorporating new provisions for wet grip performance, rolling resistance and qualification for use at severe snow conditions both for passenger car (PC) and light truck / commercial (LT/C) tyres (as were recently adopted within UN Regulation No. 117). The proposal also includes updates from relevant FMVSS and UN Regulations Nos. 30 and 54.

Explanatory report on the development and contents of the amendment concerning wet grip, rolling resistance, and other updated provisions for GTR 16 on tyres.

Proposal for a revised UN R64 that removes the provisions for tyre-pressure monitoring systems (TPMS) (to be reproduced in a new separate regulation) in order to facilitate the application of UN R64 within the International Whole Vehicle Type Approval system.

New revised proposal to delete provisions for electronic stability and brake-assist systems from UN R13-H as part of their transposition into new stand-alone regulations.

Proposed new stand-alone UN Regulation comprised of the brake assist systems provisions of UN Regulation 13-H.

Proposal for a new stand-alone UN Regulation on electronic stability control systems comprising the ESC provisions removed from UN R13-H.

Proposed text for a new regulation on tire installation for use within the International Whole Vehicle Type Approval system.

Proposal for revised transitional provisions under the regulation.

Proposal to:
a) Align definitions and content with the other tyre regulations (UN Regulations Nos. 117, 54, 75 etc.);
b) Include a definition of “manufacturer” extracted from the resolution “R.E.3”;
c) Adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links; and
d) Add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Proposal to allow Emergency Stop Signal (ESS) systems on motorcycles and related vehicles.

Proposal to introduce requirements for the approval of replacement brake lining assemblies for L-category vehicles.

Proposal to remove tables specifying general values for replacement discs and drums that are identical to the original (2.3.3.4) since such replacements must by definition have values identical to the corresponding original parts. The proposal also would change the maximum permitted thickness variation of discs for medium and heavy vehicles from 0.030 mm to 0.050 mm (the common OEM specification).

Proposal to modify the marking requirements to replace PSI with kilopascals (“kPa”). The intent is to harmonize the pressure indication and avoid confusion between UN Regulation No. 54 and US FMVSS 119 or FMVSS 139. The proposal would also change the measurement units for drum speed from min^-1 to km.h^-1 in alignment with the requirements with other tyre regulations and align the wording in Annex 7, Appendix 1 with the text of the Regulation.

Proposal to:
a) Align definitions and content with the other tyre regulations (UN Regulations Nos. 30, 117, 75 etc.);
b) Include a definition of “manufacturer” extracted from the resolution “R.E.3”;
c) Adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links; and
d) Add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Proposal to add new tyre sizes to Annex 5 of UN R54.

The current text of UN R54 does not encompass the case where a tyre designed for a “special” application can also fulfil the definition of a “snow” tyre. This proposal would allow for such tyres to be marked with the inscription M+S, M.S, or M&S while remaining in the category of use “special”.

Proposal to add load indexes to the table in the Annex 4 to keep up with the technical evolution of tyres.

Proposal to:
a) Align definitions and content with the other tyre regulations (UN Regulations Nos. 30, 54, 75 etc.);
b) Include a definition of “manufacturer” extracted from the resolution “R.E.3”;
c) Adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links; and
d) Add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Amendment to remove certain design restrictions that impede the application of new technologies, especially related to trailer power steering systems and the use of energy from the towing vehicle, including specification of the connector through which electrical energy is supplied in the proposal

Proposal for corrections to the text and equations.

Proposal to extend the possibility of actuating the service braking system to vehicles of categories M2 and N2 below 5t.