This proposal would correct an error introduced into the regulation through Supplement 16.

Front fog lamps may be reciprocally incorporated with the main beam and in some cases, it is required to switch off the front fog lamp when the main beam is operated to avoid overheating of the device. In this case, Regulation No. 19 requires a “/” in the approval marking. However, the current text in paragraph 6.3.7 of Regulation No. 48 requires that “it shall be possible to switch the front fog lamps ON and OFF independently of the main-beam headlamps”. This proposal is intended to remove the conflict between the texts of the two regulations. This proposal supersedes and replaces document GRE/2014/22 and has been prepared to remove ambiguities identified in the previous proposal.

Proposal to correct an error introduced by Supplement 21 to the 02 series of Regulation No. 7 (document WP29/2012/65). Supplement 21 introduced provisions for the use of light-emitting diode (LED) light sources and corrected the provisions concerning approval markings.

Correction to the consolidated proposal prepared by AVLI informal working group to update and revise Regulation No. 86 (document GRE/2014/30).

Document GRE/2014/31 proposes to introduce requirements to avoid intentional non-approved (voltage) variation of the passing and driving beam, using halogen light sources and to harmonize it with the operating voltage requirements in Regulation No. 48. This correction seeks to improve the text by replacing the “about value” for the reference luminous flux with the exact value of 13.2V and to simplify the C.o.P. procedure.

Text prepared by IMMA in order to introduce amendments to ensure consistency of Chapter II Vehicle lighting and light-signalling devices of the 1968 Convention on Road Traffic with regulations under the 1958 Agreement and regulations applicable in the European Union.

Clarification of certain diagrams in the original proposal (document GRE/2014/15). Supplement 17 proposes to introduce the possibility of interdependent lamps for dedicated motorcycle lamps.

OICA comments on document GRE/2014/39 proposing to align UN R48 with the proposal approved by the GRSG to require the automatic activation of hazard warning lights in buses and coaches in the event of excess temperatures in the engine and/or other compartments.

IMMA proposal to provide transitional provisions to the German proposal to delete R113 Class B headlamps from R53 (document GRE/2014/32).

Proposal for the scope, mission, and mandate timeframe for the informal group of experts.

Proposal to introduce type-approval provisions for lamps intended to provide supplemental lateral illumination of the road on the driver-side of the vehicle as a means to reduce the impact of glare from on-coming vehicle headlamps on driver vision and road visibility.

Revised proposal to introduce flashing side marker lamps for vehicles of categories M2, M3, N2, N3, O3 and O4 with the objective of improving the safety of vulnerable road users by informing them about the intended turns of buses and heavy goods vehicles and their trailers. This proposal replaces the version presented in document GRE/2014/33.

Proposals for the draft supplements to the 01 series of amendments to Regulation No. 112 and to the 01 series of amendments to Regulation No. 123.

Presentation in support of documents GRE/2014/35 and 2014/36 that would delete the requirement that the total objective luminous flux of all LED modules producing the principal passing (main low) beam of a headlamp be greater than or equal to 1000 lumens. UTAC/France argues that the requirement is design-restrictive, unnecessary given the objective criteria for luminous output and photometric grid points of the regulation, and obsolete given improvements in LED technologies.

Text prepared by Italy to delete all obsolete references in Regulations Nos. 53 and 74 in order to avoid confusion and possible incorrect application of the requirements containing these references. The deletions cover references to Regulations Nos. 1, 8, 20, 56, 57, 72, 76 and 82. These regulations have all been “frozen” (i.e., they do not apply to new type approvals) and their functions have been taken over by Regulations Nos. 112 and 113.

Proposal to reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86 into the Regulations 3, 4, 6, 7, 19, 23, 38, 50, 77, 87, 91, 98, 104, 112, 113, 119 and 123. This proposal is a revised version of document GRE/2013/55 discussed during the October 2013 GRE session.

This proposal introduces new class 5 devices made solely of retro-reflective plates with chevron type pattern to be applied to special utility vehicles or trailers not regularly covered by standard rear marking plates. The amendment also seeks to harmonize the text to cover various national requirements.

This proposal introduces new class F marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements.

Agenda for the March 31-April 3 2014 session of the Working Party on Lighting and Light-signalling Equipment.

Text prepared by the Informal Group on “Agricultural Vehicles Lighting Installation” (AVLI) to update and revise Regulation No. 86.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definition of “type”, with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings.

Although documents GRE/2013/45 and GRE-70-02 were adopted by GRE at its last (70th) session, this proposal consolidates the amendments and offers editorial improvements to the provisions concerning markings in Regulations Nos. 19, 23, 38, 65 and 119. These editorial improvements aim to clarify that the devices, and not only the samples, shall bear the trade name or mark and align the requirements with the other correctly worded regulations to avoid misunderstanding.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to amend the requirements relating to failure indication by removing the differentiation between filament and LED light sources. (Currently the provisions in UN Regulation No. 6 treat the failure of a lamp equipped with filament light sources differently to one equipped with LED. Similar requirements in UN Regulation No. 7 do not include this differentiation.)

The text reproduced below was prepared by the expert from the International Automotive Lighting and Light Signalling Expert Group (GTB) to amend the requirements to clarify the “n-1 rule” provisions in relation to an interdependent lamp system. This document has been withdrawn from consideration.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”.

Text prepared by the International Motorcycle Manufacturers Association (IMMA) to introduce the possibility of interdependent lamps for dedicated motorcycle lamps. The proposal reflects recent amendments of Regulations Nos. 6 and 7 and meets the visibility angle requirements of Regulations Nos. 50 and 53. The concern is that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features.

Text prepared by the expert from the International Motorcycle Manufacturers Association (IMMA) to introduce the possibility of installing interdependent lamps for L3 category vehicles. Also, the amendment reflects the recent amendments to Regulation No. 48, Supplement 2 to its 06 series of amendments and further includes some editorial corrections of current Regulation No. 53 texts. The concern is that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features.

Text submitted by the International Motorcycle Manufacturers Association (IMMA) to allow for the use of different brake lamp activation methods for Powered Two Wheelers (PTWs). This amendment also introduces the concept of a high-mounted stop lamp to PTWs to improve the conspicuity of the vehicles during stopping.

Text prepared by the International Motorcycle Manufacturers Association (IMMA) to correct typographical errors introduced during previous amendment to the regulation (ECE/TRANS/WP.29/2012/83). The initial changes were already in Revision 2 of UN Regulation No. 113.

Text prepared by Poland to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic levelling.

Text prepared by Japan and Finland to introduce provisions for registration plates that differ in size from the standard EU plates.

Proposal to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. Class F markings are designed with alternate stripe pattern to be applied to special utility vehicles or trailers not regularly covered by standard contour marking materials requires amending the definitions.

Draft agenda for the October 2014 GRE session without annotations (descriptions of agenda items and document references).

Revised proposal (superseding document GRE/2014/7) to introduce the possibility of interdependent lamps for dedicated motorcycle lamps. The proposal reflects recent amendments to Regulations Nos. 6 and 7 and meets the visibility angle requirements of Regulations Nos. 50 and 53. The concern is that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features.

Revised proposal (superseding document GRE/2014/8) to allow for the installation of interdependent lamps for L3 category vehicles. The amendment also reflects recent amendments to Regulation No. 48, Supplement 2 to its 06 series of amendments and further includes some editorial corrections of current Regulation No. 53 texts. The concern is that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features.

Proposal to amend UN R3 in order to address the recent introduction of devices with a reduced light distribution to be mounted no higher than 750 mm. 1. The proposal would also require colorimetric and photometric testing to type approve each variation in color of an approved device.

Proposal to delete unnecessary markings for LED front fog lamps that have non-replaceable LED modules and to correct and clarify the requirements for colour measurement and ultraviolet (UV) testing of light emitting diode (LED) modules.

Proposal to amend the test procedure for reversing lamps and maneuvering lamps equipped with light sources other than filament lamps. Currently, the lamps are required to meet photometric parameters after one minute and 30 minutes of operation. Under normal use, these lamps are operated for no more than six minutes at a time. This proposal would set the second measurement point at 10 minutes rather than 30 minutes. This change would also align the procedure with SAE standard J1889.1.

Proposal to introduce new halogen categories H18, H19 and H20 and some minor corrections to existing categories.