Presentation of changes to the original draft proposal (document GRSP-61-03) for a new regulation on the safety of hydrogen fuel-cell motorcycles and similar vehicles and explanation for the modifications. The changes have been incorporated into the revised proposal GRSP-62-02.

Proposal to modify the frequency of conformity of production inspections and random sampling. Absent ISO 9002 certification, inspections would change from “3 times a year” to “1 time a year” (i.e. annual). For ISO 9002-accredited facilities, the amendment would offer authorities flexibility for inspections every 1-2 years depending upon the results of previous inspections.

Proposal to delete measurement of the femur bending moments because such measurements are unnecessary under the full width rigid impact test.

Proposal from the GRSP secretariat to correct editorial oversights found in document GRSP/2017/21.

Proposal from the GRSP secretariat to correct editorial oversights found in document GRSP/2017/22:

1. Deletes “one of” from the phrase “one of the positions specified in paragraph 7.7.1.5.”
2. Paragraph 8.3.6. ellipsis (dots) at the end of the paragraph, indicating that the remaining previous text shall be kept, were omitted.
3. Paragraph 1.2: Deletes “and Appendix 5” to align with the text of Supplement 9 to the 06 series of amendments to UN Regulation No. 16.
4. Refers to figures 1 to 8, not 1 to 9.
5. Table 1: Deletes “F1” in the table, as this fixture is part of the corresponding ISO Standard but not in UN R16.
6. Appendix 5: Replaces “universal” by “i-size” in the title of Appendix 5, as UN Regulation No. 129 booster seats can be only i-Size or specific.

Proposal to clarify and correct the reference in paragraph 8.3.6. to UN R14 and the new UN Regulation on ISOFIX anchorages with regard to the measurement of the pitch angle used for the geometrical assessment of the installation of ISOFIX child restraint fixtures. This proposal relates directly to the supplements presented in document WP.29/2017/120.

Proposal to update the references to ISO standards in Mutual Resolution 1, Addendum 2 (document WP.29/1101/Amend.1).

Proposal from the GRSP secretariat to prohibit the use of the DETA program Unique Identifier in place of the approval mark specified in UN R22 because the current mark provides important consumer information that would be lost through use of the UI. This prohibition has similarly been approved for child restraint systems (UN R44 and R129).

Proposal to introduce a tolerance for the position of the loading device during the test. The loading device is required to be parallel to the x-y plane of the chassis. This proposal would add a z dimension to the x-y plane and set a tolerance such that the loading device may not deviate by more than 5° along the z-axis.

Research has shown that dynamic testing under Appendix 1 is more demanding than the static testing under Appendix 5. As a result, approvals based upon static testing are not equivalent to approvals based on dynamic testing. This proposal, therefore, would delete Appendix 5. In addition, this proposal amends Appendix 1 by reducing the forward movement of the head of the manikin to 1.2 m in alignment with UN Regulation No. 14. Further, the proposal would limit the movement of the seat anchorages to 100 mm to ensure a minimum residual space for the passenger between the seats. Lastly, to ensure that seat fixations are reliably fastened after relocation, the proposal would require the necessary information to be marked directly on the seat and provided in the owner’s manual.

As a counterproposal to document GRSP/2017/27 submitted by the EC, OICA suggests to group all the airbag warning requirements in one single UN Regulation (i.e. UN R16); this would avoid future administrative burden when these may need adaptation. Another solution could be to simply refer, in UN R94 and UN R137, to the label defined in UN R16; OICA suggests that GRSP discusses the most suitable approach.

In addition, OICA agrees with the EC proposal to better define the required label, in order to avoid potential misinterpretations. However, when it comes to the printing of the user information in a multitude of languages, OICA considers this is an unnecessary burden, with no benefit to the user. User manuals are placed in the vehicles at the point of sale and therefore in the local language(s); in the not so frequent cases whereby a vehicle, during its lifetime, ends up in a different country/language, the user will always be able to obtain the manual in his own language, if he so asks. OICA consequently proposes not to amend the current requirements on the issue of languages.

Proposal prepared by the experts of the Informal Working Group (IWG) on Global Technical Regulation No. 9 Phase 2 (GTR9-PH2) and proposes provisions on pedestrian safety and motor vehicles. It represents the final proposal of the Informal Group for Phase 2 of GTR No. 9, based on document GRSP/2014/15 proposing to introduce the Flex PLI lower legform impactor and related test procedures into the GTR on pedestrian safety protection, including the new bumper test area specifications.. As such, the document incorporates also the results of the Task Force Bumper Test Area as well as the comments provided in the informal document of the US from last December’s GRSP (GRSP/2017/3).

Proposal to modify the dates for phasing out Group 2 and Group 2/3 child restraint systems as proposed in document GRSP/2017/20. Approvals would cease to be granted for new type approvals from September 2021 and extensions to approvals would no longer be granted from September 2024.

Position of France concerning the need to update helmet requirements in light of new designs and technologies presenting safety benefits and raising new safety concerns.

Changes agreed by the CRS informal group for the “Phase 3” amendments (universal belted and specific-to-vehicle belted CRS) (amending document GRSP/2017/41) addressing definitions and provisions for lower tether strap and lower tether anchorages.

Changes agreed to by the CRS informal group to the proposal to correct wording and chapter references, clarify test procedures, and introduce new definitions (document GRSP/2017/42).

Changes agreed within the CRS informal group to the proposal to correct wording and chapter references, clarify test procedures, and introduce new definitions (document GRSP/2017/43).

Proposal to correct the omission of the exemption of non-integral ECRS with a stature range starting at 100 cm or above from the testing of toxicity in Supplement 1 to R129 (document WP.29/2016/106, paragraph 6.3.1.1.). This correction should also be applied to the later documents:

• GRSP /2017/44 Proposal for Supplement 7 to R129,
• GRSP /2017/43 Proposal for Supplement 4 to 01 series of amendments to R129,
• GRSP /2017/42 Proposal for Supplement 3 to 02 series of amendments to R129, and
• GRSP /2017/41 Proposal for 03 series of amendments to R129.

Update on the work to harmonize the specifications of the 3D H-Point Marchine as used in UN Regulations and UN Global Technical Regulations.

Draft definition of the mandate of the HFCV Phase 2 informal group formed to further develop the GTR on HFCV safety.

The proposal clarifies the test procedure in the amended paragraph 6.1.8 in document GRSP/2017/38 by adding one dimension (175 mm) . This dimension is in line with the dimensions of the fixture from Regulation 16 to check the vehicle safety belt length (Annex 17-Appendix 1, Figure 1) and also in line with document GRSP-61-14/Rev.1 that was adopted at the 61st session.

Presentation on the development of UN R129 and particularly of provisions for Integral, belted Universal or Specific enhanced child restraint systems.

Proposal to cease new approvals of non-integral group 2 and group 2/3 child restraint systems under UN Regulation No. 44 as of [1 September 2019]. This proposal supersedes the previous document GRSP/2017/20.

Amended version of document GRSP/2017/41 for the “Phase 3” amendments (universal belted and specific-to-vehicle belted CRS) prepared by the CRS informal group.

Proposal to amend the transitional provisions in order to explicitly confirm that approvals granted prior to the respective supplements to the 01 and 02 series of amendments and the establishment of the new guidelines on UN Regulation procedures (documents WP.29/2017/107 including Corrigendum 1 and Addendum 1) will continue to be accepted. This amendment thus confirms the understanding that the new procedures apply only to new approvals and do not affect previous approvals.

Proposal to amend the transitional provisions in order to explicitly confirm that approvals granted under the preceding series of amendments and the establishment of the new guidelines on UN Regulation procedures (documents WP.29/2017/107 including Corrigendum 1 and Addendum 1) will continue to be accepted. This amendment thus confirms the understanding that the new procedures apply only to new approvals and do not affect previous approvals.

Updated and amended proposal based on formal document GRSP/2017/39. This proposal requires the checking of non-integral child restraints (e.g., booster seats) for risk of injuries caused by narrow contact with buckle and safety-belt.

CLEPA request for a focused and urgent effort to incorporate all dummies and tools (especially including the child Q dummies integrated into UN R129 testing) into Mutual Resolution 1 which was intended as the repository for specifications of all tools used in WP.29 regulation test procedures.

Presentation in support of the proposal to delete the static test procedure for seat strength (document GRSP-62-12) from UN R80.

Video clip use in study presentation.

Video clip use in study presentation.

Presentation in support of the proposal to delete the static test procedure for seat strength (document GRSP-62-12) from UN R80.

Revised proposal, pursuant to GRSP-62 discussions, to clarify that seat belt components such as retractors shall remain functional if damaged during the load-retention test according to Annex 9 of UN R17. Such components have occasionally been damaged during testing such that their functionality has been impaired. In order to ensure adequate occupant safety, this proposal would require all safety-belt components to be included in the test installation and require post-test inspection to confirm the absence of damage.

On 14 November 2017, Korea introduced rear seat-belt reminder requirements into the KMVSS aligned with the 07 series of amendments to UN R16. The requirements become mandatory from 1 September 2019. At the same time, Korea also adopted the FlexPLI test tool for pedestrian protection testing aligned with the draft Amendment 2 to GTR No. 9. Compliance testing with the FlexPLI will start from 1 January 2018 (given that the FlexPLI has been in use under Korea NCAP since 2015).

Proposal to cease new approvals of non-integral group 2 and group 2/3 child restraint systems under UN Regulation No. 44 as of [1 September 2018].

Proposal to correct Table 1 by deleting “F1” (this fixture is part of a corresponding ISO Standard but not in UN R16) and to replace “universal” by “i-Size” in the title of Appendix 5, as UN R129 booster seats can be only i-Size or specific.

Proposal to correct paragraph 1.2. by deleting “and Appendix 5” in order to align with the text of Supplement 9 to the 06 series of amendments to UN R16, to correct Table 1 by deleting “F1” (this fixture is part of a corresponding ISO standard not found in UN R16), and to correct Appendix 5 by replacing “universal” with “i-Size” (UN R129 booster seats can be only i-Size or specific).

Proposal to clarify the text of UN R14. The current text has produced differing interpretations among Technical Services with regard to which requirements apply to central seating positions in rear rows of category M₁ and N₁ vehicles and the minimum distance between two effective lower belt anchorages (L1 and L2). The proposed amendments clarify that a reduced minimum distance of 240 mm is only allowed in the case where there is only one central seating position (i.e. in a row of 3 seating positions). Rear seat rows with an even number of seats always shall have a distance of at least 350 mm. Given that it entails new requirements, the proposal is presented as a new series of amendments with transitional provisions (proposed through 2025).

Proposal to clarify that the second level warning requirement in the 02 series of amendments to the UN R16 is dependent upon the needs of each seating position. A strict reading of paragraph 2.45. would require a second-level warning in the event of any unfastened seat-belt in a front or rear position. This proposal would clarify that the second-level warning is required depending on the individual position requirement (e.g., based on detection that a position is occupied).

Proposal to clarify that seat belt components such as retractors shall not sustain damage during testing according to Annex 9 of UN R17. Such components have occasionally been damaged during testing such that their functionality has been impaired. In order to ensure adequate occupant safety, this proposal would require all safety-belt components to be included in the test installation and require post-test inspection to confirm the absence of damage.