Proposal to correct the definition of “manual valve”, including deletion of the phrase “rigidly fixed to the cylinder or tank”.

The proposal by Belgium GRSG/2016/05 aimed at removing the amended additional safety prescriptions for trolleybuses from annex 12 of UN Regulation No. 107 for the Construction of M2 and M3 vehicles (R107), and inserting them into UN Regulation No. 100 on Electric Powertrain Vehicles (R100), see proposal GRSP/2016/07. This document explains how the scope and technical provisions for trolleybuses of R100 and R107 are complementary, but not yet fully compatible.

Proposal to introduce requirements for “obstacle detection systems to support fields of vision” (e.g., wide-view mirrors, sensors, camera systems). The aim is to decrease backover fatalities and injuries due to driver failure to adequately scan for obstacles when driving in reverse gear.

Presentation on the German effort to develop blind-spot detection performance assessment procedures pursuant to interest in making such systems mandatory on long vehicles.

Research in support of the AECS sled test pulse corridor as presented in GRSG/2016/19 (draft AECS regulation). The research demonstrates that the proposed peak G crash pulse specification is a reasonable representation of real-world crash dynamics.

Proposal to replace the term “minimum average magnification factor” with “magnification factors” in paragraph 16.1.3.1. There is no “minimum average magnification factor” in this regulation, just a “minimum magnification factor” and an “average magnification factor” and this already mentioned in the text following the revised sentence.

Presentation on Japanese legislation concerning the “Facilitation of Mobility of the Elderly, Disabled, and Other Vulnerable People through Public Transit System”.

Proposal for an informal group to develop a draft regulatory proposal for a new UN Regulation on close proximity vision and obstacle detection systems in order to establish uniform technical requirements for such close proximity vision and obstacle detection systems to prevent accidents by enabling the driver to notice any pedestrians around or behind the vehicle.

Proposal prepared by the GRSG Secretariat pursuant to discussions of document GRSG/2016/24. The proposal aims to improve and clarify provisions concerning the approval of interior materials, cables and insulation materials. The proposal adds new requirements for cable sleeves and conduits, modifies vertical testing requirements under Annex 8 to allow testing of small test samples and to clarify their fixation to the specimen holder., and adds a new Annex 10 on provisions for testing of electrical cables.

Presentation on CTIF cooperation with Euro NCAP, ISO, and others to encourage consideration of fire and rescue worker needs in responding to accidents (e.g., clear marking of vehicle propulsion system, post-crash occupant accessibility and extraction, protection against hazards).

Proposal to extend the duration of the PSG informal group until June 2018 to allow for the completion of its work.

PSG informal group proposal to correct the scope of the GTR in accordance with Part A of the GTR, its UN R43 counterpart, and corresponding regional/national interpretations and to align the impact test procedure description with that of UN R43 and ISO 3537.

Proposal to augment the provisions to address the needs of persons with reduced mobility by improving accommodations for wheelchair users and for persons who are visually and/or hearing impaired, superseding documents GRSG/2016/20 and its Corrigendum 1.

At its fifty-ninth session, GRSP approved a proposal for the 07 series of amendments to UN R16 ( (GRSP/2016/2 and GRSP/59, page 24) to mandate safety belt reminders for all vehicle seats. This proposal aligns provisions in UN R121 with the changes to UN R16:
a) the term “seat belt” is replaced by “safety belt”,
b) the symbol for safety belt, defined in item 21 of Table 1 in the Regulation, may be displayed in different colours to convey different meanings. Therefore, the existing footnote ¹⁸ has been added to item 21, and
c) this symbol may be replaced by different symbols for seats other than those of the front row. Therefore, a new footnote ²² is added to item 21.

Paragraph 5.1.5. is modified and paragraph 5.1.7. introduced to take into consideration the strict content of GRSP/59, page 24, paragraphs 8.4.3.2.1. and 8.4.4. on safety-belt reminder for occupants of rear seat row(s). This proposal does not change any of the technical requirements of UN R121.

Proposal prepared by the Chair of the Informal Working Group (IWG) on Accident Emergency Call Systems (AECS) for a draft UN Regulation on new provisions for AECS. It is mainly based GRSG/2016/19, distributed during the 111th session of the Working Party on General Safety Provisions (GRSG) and includes the modifications proposed by the IWG on AECS in informal document GRSG-111-07, as agreed by GRSG at its 111th session.

Overview of AECS, the draft regulation, and possible next steps.

Proposal to expand the scope of the regulation by deleting paragraph 1.2.2. which allows for the exclusion of “vehicles designed and constructed for special purposes where it is not possible, for practical reasons, to fit lateral protection devices” from the text. The UK submits that paragraphs 13 and 16 of the regulation provide specific provisions that address this situation whereas the exclusion clause allows for a broader interpretation that unnecessarily limits the use of lateral protection devices. Moreover, exemptions may still be accorded at the national level.

Proposal to clarify the scope and the application of the regulation. The proposal clarifies that the regulation applies to “the burning behaviour of electric cables and cable sleeves or cable conduits used in the vehicle” and it updates the reference to paragraph 5.22. of ISO 6722-1:2011. Specifically, the proposal would apply testing to electric cables, cable sleeves, and cable conduits that exceed a length of 100 mm.

At the May 2015 Type Approval Authorities Meeting (TAAM), Poland raised concerns (attached with this submission) over small M₁ vehicles being equipped with aftermarket coupling devices where the vehicle in question is not designed for towing a trailer. In effect, these vehicles are not permitted to tow trailers, but are nonetheless enabled to be equipped for such a purpose by the aftermarket devices. Therefore, Poland proposes to amend UN R55 to ensure that coupling devices are only approved for use on vehicles approved for towing trailers.

Proposal to transfer electrical safety provisions for trolleybuses (Annex 12) from UN R107 to UN R100. In 2006, the provisions of UN R36, UN R52, and UN R107 were merged through the 02 series of amendments to UN R107. In 2015, Annex 12 of UN R107 was amended to align additional safety prescriptions for electrical safety of trolleybuses with the corresponding electrical standards. However, UN R100 has evolved beyond its initial focus on battery electric vehicles and currently presents a more appropriate location for maintaining the trolleybus electrical safety provision of Annex 12. For the provisions of Annex 1 – Part 1 – Appendices 1, 2 and 3, where a list of characteristics of a trolleybus was added apart from the special environmental conditions, a reference will be inserted to Annex 6 – Part 1 and Annex 7 of UN Regulation No. 100. A corresponding proposal for amendments will be submitted as an official document to the Working Party on Passive Safety.

Proposal to harmonize UN R110 with standard ISO 11439:2013 on high pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles.

Proposal to allow the use of Class 0 hoses with couplings using sealing technologies other than those with a 45° cone. Currently, non-seamless double and single wall tubes are used in brake and fuel tubing applications, allowing for the use of a variety of end forms and coupling techniques. Provided the tubing can withstand the applicable tests according to Annex 15, Table 1, such configurations should be permitted under UN R67 in order to remove an unwarranted design restriction.

Proposal to allow the use of Class 0 hoses with couplings using sealing technologies other than those with a 45° cone. Currently, non-seamless double and single wall tubes are used in brake and fuel tubing applications, allowing for the use of a variety of end forms and coupling techniques. Provided the hose assembly can withstand the impulse test of paragraph 1.7. and the tests of Annexes 5A (overpressure test) and 5B (external leakage test), such configurations should be permitted under UN R67 in order to remove an unwarranted design restriction. In cases where a soft seal body (e.g. O-ring) is used, the compatibility of the material with use conditions must be demonstrated by testing according to Annexes 5D (CNG/LNG compatibility test), Annex 5F (resistance to dry heat) and Annex 5G (ozone aging).

Proposal to correct a typographical error in paragraph 7.1. where the reference should be to paragraph 8.22 rather than 8.21, to remove a duplicate and contradictory reference in Annex 4A to the requirements of Class 1 pressure relief valves, and to align paragraph 2.2. of Annex 4H with paragraph 18.6.1.2. limiting the delay in switching-off of the automatic valve after stalling of the engine to two seconds (rather than five as presently in the text).

Proposal to include the liquefied natural gas (LNG) fuel connector provisions as specified in ISO 12617:2015.

Proposal to define an exemption for handles from “residual/survival space” intrusion requirements for vehicle spaces not intended for occupants. Handles and handholds used to assist passengers in entering and exiting a bus are located outside of passenger seating and standing areas where OICA argues that they do not present a danger; however, the current rollover testing provisions could result in their inclusion in the area defined as “residual/survival space” where any intrusion is prohibited.

Proposal to harmonize the Russian text with the English-language version of the regulation.

Proposal prepared by the UNECE secretariat to align the provisions of UN Regulation No. 105 with those of the new 2017 edition of the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR).

Proposal for new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur.

Proposal to allow for the use of natural gas refrigeration systems to vehicles propelled by natural gas (CNG or LNG). This proposal addresses a new, environmentally friendly natural gas fuelled refrigeration system for trucks with refrigerated loads that already are propelled by natural gas. Currently paragraph 18.1.7.1 allows heating systems to be fitted on vehicles to heat the passenger compartment and/or the load area of a vehicle, however, the same provision omits cooling systems that are used on trucks for the carriage of loads requiring refrigeration.

Proposal to add a telltale and symbols for “Accident Emergency Call System (AECS)”.

Proposal to expand the scope of the regulation by deleting paragraph 1.2.2. which allows for the exclusion of “vehicles designed and constructed for special purposes where it is not possible, for practical reasons, to fit lateral protection devices” from the text. The proposal allows Type Approval Authorities to nonetheless exempt “vehicles where any LPD (e.g. fixed, removable, foldable, adjustable, etc.) is incompatible with their on-road use” through the addition of new paragraphs.

Proposal from the AECS informal group for a regulation to enable the approval of Accident Emergency Call Devices (AECD) intended for M1 and N1 vehicles, the approval of M1 and N1 vehicles with regard to the installation of an AECD, and/or the approval of M1and N1 vehicles with regard to their Accident Emergency Call System (AECS) or with regard to the installation of an AECD which has not been separately approved under the regulation.

Proposal to augment the provisions to address the needs of persons with reduced mobility by improving accommodations for wheelchair users and for persons who are visually and/or hearing impaired.

Corrections to the proposal to augment the provisions to address the needs of persons with reduced mobility by improving accommodations for wheelchair users and for persons who are visually and/or hearing impaired. The corrections include an additional paragraph with requirements for loudspeaker systems.

Proposal to align the requirements for plastic panes other than windscreens with the requirements of plastic pane windscreens. This includes amendments concerning rigid plastic panes, flexible plastic panes and rigid plastic multiple-glazed units. The proposed modifications to this type of glazing are in line with the requirements of Supplement 4 to the 01 series of amendment of UN Regulation No. 43.

Proposal to harmonize UN R110 with standard ISO 11439:2013 on high pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles.

Proposal to reduce the administrative burden in obtaining approvals for electrical cables according to UN Regulation No. 118. The experts from Finland, France and Germany agreed that the change from ISO 6722:2006 to ISO 6722-2011 does not impact the degree of safety and, therefore, the test reports or approvals established under the older version of the ISO standard shall remain valid.

Proposal to improve and clarify provisions concerning the approval of interior materials, cables and insulation materials. The proposaladds new requirements for cable sleeves and conduits, modifies vertical testing requirements under Annex 8 to allow testing of small test samples and to clarify their fixation to the specimen holder., and adds a new Annex 10 on provisions for testing of electrical cables.