Proposal to add a trigger threshold requirement and to modify the sampling rate, deceleration limit and data selection criteria for category B brake-assist systems.

Presentation supporting documents GRRF/2015/25, /29, and /32 proposing to:
a) Align definitions and content of UN tyre regulations;
b) Include a definition of “manufacturer” extracted from the resolution “R.E.3”;
c) Adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links; and
d) Add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Proposal to improve the wording of the draft amendment on lane-keeping assistance systems, based on document GRRF-79-04.

Proposal to change the draft amendments to the 02 series of amendments to Regulation No. 30 regarding tyre dimension requirements.

Document GRRF/2015/27 proposes to modify the marking requirements to replace PSI with kilopascals (“kPa”). The intent is to harmonize the pressure indication and avoid confusion between UN Regulation No. 54 and US FMVSS 119 or FMVSS 139. This proposal would allow for the use of kPa markings in place of PSI prior to the 1 January 2018 transition date.

Proposal to correct errors and remove inconsistencies in the current regulatory text, including a correction to the formula used in Annex 12, Appendix 4 “Test report on the compatibility of the inertia brake control device, the transmission and the brakes on the trailer”.

Proposal to remove tables specifying general values for replacement discs and drums that are identical to the original (2.3.3.4) since such replacements must by definition have values identical to the corresponding original parts. The proposal also would change the maximum permitted thickness variation of discs for medium and heavy vehicles from 0.030 mm to 0.050 mm (the common OEM specification).

Documents GRRF/2015/40 and 41 propose to align GTR 3 and UN R78 with the provisions for anti-lock braking systems used in other regulations. The proposal clarifies the limits on the use of any temporary ABS deactivation switch and prohibition against permanent disabling of ABS if fitted on a motorcycle. IMMA wishes to make the wording more technology-neutral, clarify test conditions considered impractical, and allow time for manufacturers to comply (i.e., add transitional provisions).

Document GRRF/2015/38 proposes to change the measurement units for drum speed from min-1 to km.h-1 in alignment with the requirements with other tyre regulations. This proposal would clarify a footnote reference by replacing “speed categories N or P” with “speed category symbols N or P”.

Document GRRF/2015/39 proposes to change measurement units for drum speed from min-1 to km.h-1 to align the
requirements with other tyre regulations. This amendment proposal would clarify wording:
1. “speed category symbol” to “speed symbol”,
2. “load capacity index” to “load index”,
3. correct reference to para. 3.2.13. of the Regulation in Annex 7, Appendix 1, and
4. correct the boundary value of the load index in Annex 7, Appendix 1.

The current text of UN R54 does not encompass the case where a tyre designed for a “special” application can also fulfil the definition of a “snow” tyre. This proposal would allow for such tyres to be marked with the inscription M+S, M.S, or M&S while remaining in the category of use “special”.

Discussion document raising concerns and offering proposals concerning motorcycle ABS testing.

Proposed additions to the Statement of technical rationale and justification in GTR 16 (tyres), especially to clarify application and future development of the regulation.

CLEPA remarks defining sensor mounting requirements for heavy vehicles (Horizontally: up to 600 mm out of vehicle center; Vertically: between 330 mm and 800 mm above road-surface level) in order to avoid safety risks.

EC responses to IMMA comments (document GRRF-80-13) on the proposa to align the text with the provisions for anti-lock braking systems (ABS) used in other regulations (document GRRF/2015/41).

EC responses to IMMA comments (document GRRF-80-13) on the proposal to align the text with the provisions for anti-lock braking systems (ABS) used in other regulations (document GRRF/2015/40).

Proposal to remove provisions related to temporary/spare units, TPMS and to exceptional cases that would require type approval under UN R75 or R106.

Proposal to ensure that coupling balls do not block rear lighting and/or registration plates. In line with the EU General Safety Rule, Annex IV specification for application of UN R55, couplings that might block lighting or plates must be removable, repositionable, and unlockable in order to make it easier for users to remove them or reposition them when not in use (e.g., towing a trailer.) Coupling balls that are so designed as to be unable to block lighting or plates may still incorporate locks and/or require tools to remove or reposition.