Items 12 and 13 commending and endorsing efforts between WP.1 (road safety) and WP.29 (vehicle safety) to cooperate with regarding to automated driving.

In response to discussions over the application of Revision 3 to the 1958 Agreement concerning extensions of approvals granted prior to Revision 3, IMMA presents an example from UN R50 where application of Revision 3 presents concerns.

Request of the DETA informal working group for WP.29 decisions during its March 2018 session on the program development, including initial deployment and rebranding to communicate that the system is not limited to the exchange of type approval information, but can be used for other vehicle-related information.

OICA comments on EDR versus DSSA and on Driver Availability Recognition as well as relationship of automated driving efforts with the 1998 Agreement.

OICA and IMMA comments on the new procedures of Revision 3 to the 1958 Agreement concerning the retroactive application of Supplements to extensions of type approvals.

Voting table for 1998 Agreement decisions.

Voting form for decisions pending under the 1997 Agreement on Periodical Technical Inspections.

Japan comments in relation to the EU submission WP.29-174-09.

Proposal of subjects for work from the EU and Japan.

Partial OICA research regarding supplements developed prior to Revision 3 of the 1958 Agreement where application of Revision 3 with regard to extensions of approvals (para. 31(b)) would present problems for manufacturers.

Corrigendum from the ITS/AD informal group to note that the provisions in the table ending on page 11 for ACSF Category B2 and ACSF Category E are under discussion.

Proposal to delete a description of the L₄ vehicle category (motorcycles with a side car) from Annex 3 to Regulation No. 41. These vehicles fall under the scope of UN R9, having been removed from the scope of UN R41 as of the 04 series of amendments.

Extensive changes to UN R51 as developed mainly by the informal working group on Additional Sound Emission Provisions (ASEP II), but including further proposals submitted through GRB. All of these proposals were consolidated by GRB during its September 2017 session in Annex II to the session report. GRB intends to hold a final review of the changes, including whether they constitute a new series of amendments, during its January 2018 session, (i.e., prior to the March 2018 WP.29 session that will consider this document). The draft changes include proposals to

1. amend the scope to be design-neutral and reflect the driving situations covered by the Regulation;
2. highlight that ASEP apply to vehicles and their electric sound enhancement systems such as the Audible Vehicle Alert System (AVAS) and silencers equipped with an active cancelling system
3. update the “backfire” assessment procedure; and
4. clarify the gear ratio anchor point in Annex 7 as defined via Annex 3
5. Paragraph 1: The scope was originally drafted for the Annex 3 test which refers to normal urban driving. A proposed additional sentence covers the intention of Annex 7.
6. Paragraph 2.8.1.: Adopt the wording from standard ISO 362-1:2015 for clarity. If an electric motor is not operational during the type approval tests, then its power must not contribute to the calculation of the power to mass ratio (PMR).
7. Paragraph 2.24., table: Amendments regarding paragraph 2.2.7.4. of Annex 3 because paragraph 2.2.7.4. is new. Amendments also for line BB’ to reflect that the measurement will not end after line BB’. For the speeds vAA’, vBB’ and vPP’, a wrong reference coming from ISO was corrected.
8. Paragraph 2.27.: A new definition of “kickdown” was introduced since this term is used in this Regulation. With a large variety of products, it is unclear what “kickdown” exactly means. This definition is a design neutral approach and reflects the intention of Annex 3 and Annex 7.
9. Paragraph 2.28.: Prevention of downshift is a legal measure to ensure that the vehicle can be tested within the test conditions as specified by this Regulation.
10. Paragraph 3.3.: Deletion of meaningless sentence given the requirement that the vehicles have to be loaded in order to be able to achieve the urban driving conditions as described in paragraph 3.1.2.2. of Annex 3. The sentence has similarly already been deleted in Regulation (EU) No. 540/2014.
11. Paragraph 6.2.3.: Amend paragraph 11.6 to exempt vehicles with a serial hybrid drive train until July 2022 from ASEP since these vehicles do not have the internal combustion engine running within the control range of Annex 7 and therefore cannot yield valid test results.
12. Annex 1, Appendix 1: For the test method according to 3.1.2.1 the pre-acceleration length may differ per gear ratio. In this case, it is necessary to report the pre-acceleration length per gear ratio.
13. Annex 1, Appendix 2: Missing elements of the information document have been added, namely “0.2. type” and “3.2.6. pressure charger(s)”.
14. Annex 3, paragraph 2.1.: Lower temperatures will lead to slightly higher test results due to an increased tyre rolling sound. Thus, testing at lower temperatures will be a disadvantage for the manufacturer. If for practical reasons the manufacturer wishes to carry out tests at lower temperatures, this shall be accepted by the type approval authority.
15. Annex 3, paragraph 2.2.1.: For M1 and N1, the current provision has led to ambiguities about its meaning. The proposed new sentence clarifies the meaning. Further, the tolerances are broadened, as research shows, that the impact of the test mass can be neglected in a wide range. For M2, M3, N2 and N3, the current provision has led to ambiguities about its meaning. The proposed new sentence clarifies the meaning. If the test mass of the vehicle is equal to the target mass, the target mass shall be achieved with a tolerance of ±5 per cent according to equation (2) in paragraph 2.2.7.1. of Annex 3. Consequently this has to be valid also for the test mass mt. If the test mass of the vehicle is lower than the target mass according to equation (12) and (13) in paragraph 2.2.7.1. of Annex 3, the test mass shall be achieved with a tolerance of ±5 per cent. Concerning M2 and M3, for clarification and to avoid misunderstanding, the loading conditions for complete vehicles of category M2 (M > 3,500 kg) and M3 were aligned with the requirements for incomplete vehicles of category M2 (M > 3,500 kg) and M3. As a consequence, vehicles of category M2 (M ≤ 3,500 kg) have to be added to the table and their test mass requirement has to be aligned with those of vehicles of category M1 and N1.
16. Annex 3, paragraph 2.2.6.: add conditioning provisions for exhaust systems containing fibrous materials,
17. Annex 3, paragraph 2.2.7.1.: See the above justification for M2, M3, N2 and N3 in paragraph 2.2.1.
18. Annex 3, paragraph 2.2.7.4.: If a manufacturer does not produce vehicles with two axles only, he is not able to calculate the right test mass for his vehicles with more than two axles. For calculating the test mass, a vehicle with two axles has to be put on a scale to measure the unladen front axle load, mfa load unladen, and the unladen rear axle load, mra load unladen, for being able to calculate munladen as given in formula (3) of paragraph 2.2.7.1. of Annex 3. In addition, a new paragraph provides a procedure for calculating the test mass of a virtual vehicles with two axles, based on an existing vehicle with more than two axles, when a vehicle with two axles is physically not available to be put on a scale.
19. Annex 3, paragraph 3.1.2.1.: Proposal to extend the measurement to a position where misfiring is detectable. A redundant sentence is deleted per paragraph 2.2.4.
20. Annex 3, paragraph 3.1.2.1.4.1.(d): Clarify gear usage where one gear ratio is above 2 m/s² and the other below a_urban.
21. Annex 3, paragraph 3.1.2.1.4.1.: Clarify the proper setup for testing for vehicles with very short gear ratios.
22. Annex 3, paragraph 3.1.2.1.4.3.: Introduction of specifications for vehicles with only one gear ratio.
23. Annex 3, paragraph 3.1.2.1.5.: Simplify testing. With a fixed vehicle length, it is not necessary to adjust the test equipment (light barriers, pylons) for each vehicle.
24. Annex 3, paragraph 3.1.2.2.1..: Clarify the gear ratio selection procedures,
25. Annex 3, paragraph 3.2.3.: Reference correction
26. Annex 3, paragraph 3.2.5.3.: Reference correction
27. Annex 4, paragraph 1.: The performance of the fibrous material can be checked by completely removing the fibrous material. This reintroduces an option removed when Annex 5 of the 02 series of amendments was revised.
28. Annex 6, paragraph 2.1.: Proposal to simplify and clarify CoP. During the conformity of production procedures, neither the vehicle nor tyres will have a proper preconditioning. In many cases, the vehicles are foiled and parts may be missing as theft protection. It is very unlikely that the vehicles will have already the same performance as the type approval vehicle. This provision adopts the specifications from the revised ASEP provisions (Informal document GRB-65-26, Annex 7, para. 1). In addition, the range of masses was broadened in the same way as proposed for type approval.
29. Annex 6, paragraph 3.: Reference correction.

Proposal to include the following transitional provision, “Until 18 months after the date of entry into force of the Supplement 3, it shall not apply to extensions of existing approvals, originally granted prior to the date of entry into force of Supplement 3.” This document was submitted after the WP.29 filing deadline in order to reflect recent developments. At its September 2017 session, GRB adopted a draft Supplement 3 to the 03 series of amendments to UN Regulation No. 51 and requested the secretariat to submit this proposal to the March 2018 session of WP.29. This was done in December 2017 (ECE/TRANS/WP.29/2018/7). At its next session in January 2018, GRB reviewed the proposal and decided to complement it with a new provision. The secretariat was requested to submit the modification as an addendum to the original WP.29 document (ECE/TRANS/WP.29/2018/7/Add.1).

Proposal to enable activation of the ESC optical symbol in cases of a corrective steering function intervention when the CSF intervention is activated under the control of an ESC system. The aim is to avoid separate requirements for brake-actuated and steering-actuated vehicle stability functions (VSF) that would lead to two optical warnings where only one is necessary. This would enable use of the ESC intervention tell-tale for CSF steering intervention.

Proposal to

1. delete redundant provisions (paragraphs 2.2. and 2.2.1.) in favor of paragraph 5.2.2.13. which requires all O4 trailers to be equipped with Anti-lock Braking Systems (ABS) of Category A.
2. clarify exemptions from electronic stability control requirements, and
3. enable the verification of sufficient movement of the balancer without having to take measurements underneath the trailer.

Proposal for editorial improvements, including to update a cross-reference in paragraph 3.4. to read “3.1.2” pursuant to the earlier division of paragraph 3.1 into separate paragraphs 3.1.1. and 3.1.2.

Proposal to allow the use of the flashing electronic stability control (ESC) tell-tale to indicate the intervention of a corrective steering function (CSF) in cases where the CSF is controlled by the ESC (or other vehicle stability function) system. Outside such cases, CSF interventions are indicated by a continuous optical signal displayed for the duration of the intervention.

Proposal to expand the scope of UN R90 to include requirements for the approval of replacement brake lining assemblies for L-category vehicles.

Proposal to enable activation of the ESC optical symbol in cases of a corrective steering function intervention when the CSF intervention is activated under the control of an ESC system. The aim is to avoid separate requirements for brake-actuated and steering-actuated vehicle stability functions (VSF) that would lead to two optical warnings where only one is necessary. This would enable use of the ESC intervention tell-tale for CSF steering intervention.

Proposal to correct references to Regulations Nos. 30 and 54 following renumbering of paragraphs in these regulations.

Proposal to align UN R43 with GTR 6 and UN R125 with regard to the aiming positions of the driver’s eyes. This proposal corrects inconsistencies introduced during the transposition of GTR 6 into UN R43.

Proposal to correct the omission of Class VII devices from the communication form described under Annex 3 of the regulation.

Proposal to correct the omission of Class VII devices from the communication form described under Annex 3 of the regulation.

Proposal to

1. introduce new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur,
2. establish procedures for the approval of non-seamless gas tube(s), gas tube(s) made of materials other than copper, stainless steel, and steel with corrosion-resistant coating, and their couplings in Liquefied Petroleum Gas (LPG) vehicles provided they can withstand the applicable tests according to Annex 15, and
3. require marking or other means of approval identification on accessories of the container (multivalve or, when approved separately, pressure relief valve (discharge valve) and pressure relief device).

Proposal to replace the prohibition against the use of reinforced insulation for trolleybus circuits directly connected to the overhead power line with a requirement that such circuits shall be double insulated.

Proposal to replace the prohibition against the use of reinforced insulation for trolleybus circuits directly connected to the overhead power line with a requirement that such circuits shall be double insulated. Please note that the linked document should read “Supplement 2” in place of “Supplement 6” per notification by the WP.29 secretariat.

Proposal to

1. augment the provisions to address the needs of persons with reduced mobility by improving accommodations for wheelchair users and for persons who are visually and/or hearing impaired, and
2. replace the prohibition against the use of reinforced insulation for trolleybus circuits directly connected to the overhead power line with a requirement that such circuits shall be double insulated.

Proposal to harmonize the requirements on Compressed Natural Gas (CNG) and/or Liquefied Natural Gas (LNG) vehicles of UN Regulation No. 110 with those of the international standard ISO 11439:2013.

Proposal to replace the term “roof” with the term “ceiling” throughout the text pursuant to Supplement 1 to the 02 series of amendments which modified the definition of “interior compartment” (previously “passenger compartment”) in paragraph 2.2. The definition replaced the term “roof” by “ceiling” in reference to the upper boundary surface of the compartment definition; however, the change in terminology was not reflected throughout the rest of the text. This proposal corrects that omission.

Proposal to replace the term “roof” with the term “ceiling” throughout the text pursuant to Supplement 1 to the 02 series of amendments which modified the definition of “interior compartment” (previously “passenger compartment”) in paragraph 2.2. The definition replaced the term “roof” by “ceiling” in reference to the upper boundary surface of the compartment definition; however, the change in terminology was not reflected throughout the rest of the text. This proposal corrects that omission.

Proposal to apply footnote ¹⁸ to the symbol for tell-tale No. 1 (master lighting switch) in order to simplify the treatment of colour changes of tell-tales. Footnote ¹⁸ specifies "“Symbol may be shown in other colours than specified in column 5 in order to convey different meanings according to the general colour coding as proposed in paragraph 5. of ISO 2575-2004.” This proposal clarifies the existing understanding of the intent of the regulation and in particular addresses concerns over interpretation where tell-tales Nos. 1 and 19 have been combined.

Proposal to apply footnote ¹⁸ to the symbol for tell-tale No. 1 (master lighting switch) in order to simplify the treatment of colour changes of tell-tales. Footnote ¹⁸ specifies "“Symbol may be shown in other colours than specified in column 5 in order to convey different meanings according to the general colour coding as proposed in paragraph 5. of ISO 2575-2004.” This proposal clarifies the existing understanding of the intent of the regulation and in particular addresses concerns over interpretation where tell-tales Nos. 1 and 19 have been combined.

Proposal to exempt all heaters located outside the passenger compartment and using water as a transfer medium from the requirements of the annexes on air quality and temperature. The current text only exempts combustion heaters.

Proposal to reinsert text in paragraph 1.3 concerning differentiation of types according to trade name or mark that was inadvertently omitted from Supplements 27 and 28 to the 01 series of amendments.

Proposal to correct a reference to standard IEC (pursuant to a change in paragraph numbering of the IEC standard) and to align UN R37 with UN R48 and UN R128 with regard to the use of the term “chromaticity area”. The wording “required tolerance area” in case of colour is changed to “required chromaticity area” to align with Regulation No. 48. This proposal was initiated by a proposal to amend Regulation No. 128 aimed at avoiding confusion with other tolerance areas.

Proposal to introduce requirements and test specifications for light emitting diode (LED) light sources for forward lighting.

Proposal to change the units for vehicle masses from tonnes to kilograms in R.E.3.

Proposal to correct a number of editorial errors in sheets of filament light sources and to update International Electrotechnical Commission (IEC) cap sheet numbers in the IEC cap sheet references.

Proposal to introduce a new light emitting diode (LED) forward lighting light source category L1/6. The proposal is part of a package which also includes amendments to Regulation No. 128. 2. GTB proposes one category L1/6 with “maximum test temperature” 65 °C. The definition of the maximum test temperature is necessary to ensure interchangeability between approved light sources from different manufacturers. A separate (unique) light source category is specified for every “maximum test temperature”. The choice of installation of a light source with a given maximum test temperature is based on the application in the vehicle and determined by due diligence of the car maker and set maker, in the same way as is now the case with LED modules. (This revised version of the original document corrects minor inaccuracies in formatting of text boxes on some drawings.)

Draft listing of global technical regulation development programs organized into relative categories of priority.

Proposal to introduce provisions for driver-initiated automated lane-change systems (Category C ASCF) and for automated emergency steering functions (ESF). This proposal includes amendments the annex on complex electronic systems (Annex 6), in particular, to require auditing of the methodologies used to ensure system safety at both concept and system level. The concept level specifically requires consideration of interaction with other vehicle systems.

Proposal to update the references to ISO standards in Mutual Resolution 1, Addendum 2 (document WP.29/1101/Amend.1).

Update to the original agenda in order to add references to additional documentation and to delete references to documentation where none has been received.