Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to introduce light source categories WT21W and WT21/7W.

Submitted by the International Automotive Lighting and Light Signalling Expert Group (GTB) in order to amend the requirements for installation of front-position lamps.

Submitted by the International Automotive Lighting and Light Signalling Expert Group (GTB) and proposing to revise the requirements on replacing light sources.

Submitted by the International Automotive Lighting and Light Signalling Expert Group (GTB) and proposing to clarify and simplify the transitional provisions.

Submitted by the International Automotive Lighting and Light Signalling Expert Group (GTB) and proposing to clarify the general provision to determine the mounting height of the lamp in paragraph 5.28.4.

Submitted by the Netherlands to introduce a mandatory requirement for fitting an operating tell-tale on the daytime running lamp, in case the failure provision (for the light sources) according to paragraph 7.4.2.(b) of UN Regulation No. 87 is applied.

Submitted by Germany to clarify the requirements and to avoid the need for a telltale where one or more Light Emitting Diodes (LED) or LED modules, used to produce the principal passing beam, are wired such that the failure of any LED or LED module causes all the LED to stop emitting light.

Submitted by Poland to replace document GRE/2012/27 proposing an alternative set of requirements for the initial aiming of dipped-beam headlamps and allowing to remove the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic levelling.

Submitted by Germany and based on informal document GRE-68-30, proposing to delete the exemption for category M1 and N1 vehicles from the requirement for a minimum distance between the inner edges of two adjacent lighting surfaces.

Submitted by Germany proposing to insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources. This proposal supersedes document GRE/2012/20 and informal document GRE-68-03.

Submitted by Germany proposing to update the Conformity of Production requirements (CoP).

Submitted by Germany proposing to update the Conformity of Production requirements (CoP).

Submitted by Germany proposing to update the Conformity of Production requirements (CoP).

Submitted by Germany to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

UN R7 has no requirements concerning changes in lamp luminance. Therefore, certain lamps which could not be installed in accordance with UN R48 could nonetheless obtain type approval and be sold in the aftermarket. This proposal would prevent such an occurrence. This document supersedes GRE-68-29.

Submitted by Germany in order to update the Conformity of Production (CoP) requirements.

Text prepared by Germany, with support from the Netherlands, to finalize the deletion of distributed lighting systems (DLS), or rather light generators, from the regulations.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to amend the transitional provisions to cease granting new type approvals for the “Sealed Beam” headlamps and to correct the title of UN Regulation No. 31.

Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Text prepared by OICA to extend the scope of the Regulation to all kinds of power train systems above a certain working voltage level, when they are in charging mode and including type approval of separate electrical components for the “REESS charging mode coupled to power grid” configuration.

Corrections to document GRE/2013/3 (proposal to extend the scope of UN R10) prepared by the Secretary to GRE.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to amend the provisions concerning the heat test requirements for conformity of production.

Text prepared by Poland and Austria to clarify the possibility of installing on vehicles light-signalling devices which obtained a type approval according to component UN Regulations.

Text prepared by France and Germany to implement direction indicator lamps with a variable apparent surface into UN Regulation No. 6.

Text prepared by France and Germany to implement direction indicator lamps with spatial variation of the intensity into UN Regulation No. 48.

Text prepared by the Netherlands to harmonize the general wording used in the communication form with the corresponding wording in Regulation No. 7.

Text prepared by CEMA updating Regulation No. 86.