Proposal to amend the text to enable its application to ADS vehicles.

Proposal to introduce a new “call for help” signal.

Proposal to correct errors and omissions in the 01 series of amendments. Further details can be found in informal document GRE-94-02.

Proposal to clarify manufacturer logo requirements across several paragraphs: confirming that non-illuminated graphic marks are not considered logos (para. 2.1.7.); permitting vehicle manufacturers to keep the inner portion of a front position lamp active when an AFS headlamp substitutes the outer portion (para. 5.12.1.4.); improving logo language for Light Signalling Devices approved to UN R148 (para. 5.30.1.); and clarifying that Road Illumination Devices approved to UN R149 shall not include a manufacturer logo (para. 5.30.2.).

roposal to expand the application of glare-free Adaptive Driving Beam (ADB) for category L₃ motorcycles under UN R149, by introducing additional driving beam classes aligned with UN R53 motorcycle requirements and adding symmetrical passing beam-based photometric requirements below the H-H line (Table 13, Part C). Recent technological advances have made ADB electronics more practical for a broader range of motorcycles, and these amendments aim to enhance traffic safety by reducing glare while maintaining adequate rider visibility.

Proposal to introduce new LED light source categories L2 and L3 in R.E.5. Further details can be found in informal document GRE-94-12.

Proposal to amend UN R150-01 addressing three main issues. First, since the GRE-adopted proposal to delete the unique identifier (GRE-92-18) was not part of the March 2026 WP.29 submission, the regulation text requires amendment in the interim, though this may become unnecessary if merged with GRE-92-18. Second, the approval marking approach is aligned with UN R148 by including one example in the body text and referencing other arrangements in Annex 10, allowing deletion of the Table 1 reference and redundant ratio explanations from Figure A10-I. Third, the outdated requirement for function symbols to be placed diametrically opposite the approval number — inherited from UN R3 and R7 but already removed in UN R148 — is deleted from Annex 10, along with a clarifying amendment to the note below Figure A10-I to prevent inconsistent interpretations among technical services. Further details can be found in informal document GRE-94-11.

Proposal to introduce a clarification of grouped markings and labels. Further details can be found in informal document GRE-94-07.

Proposal to correct inconsistencies and calculation errors in Conformity of Production (CoP) tables across both series of UN R149, which may otherwise cause confusion for manufacturers and technical services.

In UN R149-00, corrections include: deletion of erroneous maximum values at point 50L in CoP tables for Classes C, V and W Bend Light; correction of miscalculated 20% and 30% CoP minimum values for Classes C and V Bend Light Category 1; correction of the Class W non-bending mode maximum value at Segment 10 and its derived CoP values; and correction of rounding errors in Class R CoP minimum values.

In UN R149-01, corrections include: updating the Class W Bend Light CoP maximum at point BR to align with the type-approval table; correcting miscalculated Class R Bend Lighting CoP values; and fixing table note references in Annex 4 following the introduction of scientific notation in the 01 series.

Further details can be found in informal document GRE-94-10.

Proposal to clarify and modernize lamp installation and component requirements in UN R48 and UN R148:

• Remove the “band/strip” terminology and expand the definition of a pair of lamps to cover full-width designs
• Remove the three-device maximum for Y-lamps to ensure technology neutrality
• Add a new paragraph §5.5.5 defining a pair as a two-lamp system
• Relocate light source requirements from UN R48 to UN R148 §4.7.3 to ensure at least one light source per side
• Remove the 0.8-metre minimum length requirement
• Clarify that definitions in §2.4.10 apply only to the relevant vehicle categories
• Update provisions for light source positioning in UN R148
• Clarify §4.8.1.3 in UN R148
• Add new sampling provisions in §4.8.11 for testing band/strip lamps

Proposal to clarify the 80% failure criterion for Conformity of Production (CoP) checks by confirming that CoP tables represent a simplified subset of the full Class C type-approval measurement points, and to exclude overhead requirements (items S50 and S100 in Tables 6 and 7) from the passing beam failure detection criterion, as these may be fulfilled by position lamps. Further details can be found in informal document GRE-94-08.

Proposal to introduce selective yellow as an permitted alternative to white for front position lamps and daytime running lamps in UN R48 and UN R148. Studies confirm that selective yellow performs equally to white for oncoming vehicle recognition and speed estimation. Unlike historical filament lamp applications where a yellow filter reduced luminous intensity, modern LEDs achieve the same intensity levels without reduction. Specific amendments include: updating §5.15 to reflect selective yellow options and removing a duplicated front fog lamp requirement; amending §§6.9.7 and 6.19.7 to deactivate selective yellow position and daytime running lamps on the relevant side during direction indicator activation; and aligning UN R148 (01 series) by amending §§5.1.7, 5.4.7 and Annex 1 accordingly. The colour boundaries for selective yellow are already defined in §2.11.1.2 and require no amendment. Further details can be found in informal document GRE-94-05.

Proposal to improve the clarity and structure of Conformity of Production (CoP) requirements for driving beams in UN R149 by following the approach used in UN R123.

Proposal to exclude retro-reflective devices and markings from the requirement of “Red light to the front” and “White light to the rear”.

Proposal to align the Exterior Courtesy Lamps provisions of the 08 series amendments with those of the 09 series.