Current draft text including changes made during the 18th subgroup session and prepared as the basis for discussions during the 19th subgroup session.

Australian proposal to adapt UN R14 to current Australian child restraint system anchorage requirements within the context of enabling the use of UN R14 within the international whole vehicle type approval system.

Working draft prepared pursuant to discussion through the 18th SG58 subgroup session. Basis for discussions at the 19th subgroup session.

Draft text showing changes made to the GTR on tyres under Amendment 1 (which is primarily aimed at introducing provisions for tyre rolling resistance and performance in severe snow conditions).

Updated paper on the grouping of lighting regulations under one of three new regulations as follows:
Light Signaling Devices incorporating Regulations 4, 6, 7, 23, 38, 50, 77, 87, and 91
Forward Lighting Devices incorporating Regulations 19, 98, 112, [ 113 ], 119, and 123
Retro-Reflective Devices incorporating Regulations 3, 27, 69, 70, and 104

Proposal to further refine the transitional provisions of UN R48. In 2014, the transitional provisions of UN R48 were changed in order to avoid having more than one series of amendments in force at the same time (via Supplement 3 to the 06 series of amendments). This change allows earlier series of amendments to be “frozen” and used under the International Whole Vehicle Type Approval system (IWVTA) as “versions” of UN R48. However, the possibility for the partial application of a series of amendments resulting from the installation of new equipment on a vehicle approved to an earlier series has been raised within the IWVTA. This proposal refines the transitional provisions in order to enable partial application of a series through an extension of the existing approval rather by requiring a new approval. At the same time, the proposal aims to ensure that the safety objectives of UN R48 are met.

This document is the draft revision to the existing guidelines document WP29/1044/Rev.1 which includes the changes discussed at the 18th SG58 meeting and will be used as a base document for discussion at the 19th SG58 meeting.

It also includes:
1. OICA responses/comments to the proposals and comments made by the EC (see SG58-18-08)
2. OICA proposal to revise §43, as requested at the November 2015 meeting (see SG58-19-01, Action item 6)
3. Revision to the transitional provisions in chapters B (equipment and parts), C (installation of equipment and parts), D (replacement parts for vehicles in use), jointly developed with CLEPA
4. Some further proposals by CLEPA, that can be supported by OICA

Consolidated version of the working draft amendment to WP29/1044/Rev.1, incorporating changes agreed during the 18th subgroup session and the following:

1. OICA responses/comments to the proposals and comments made by the EC (see SG58-18-08)
2. OICA proposal to revise §43, as requested at the November 2015 meeting (see SG58-19-01, Action item 6)
3. Revision to the transitional provisions in chapters B (equipment and parts), C (installation of equipment and parts), D (replacement parts for vehicles in use), jointly developed with CLEPA
4. Some further proposals by CLEPA, that can be supported by OICA

Proposal to clarify the provisions for the minimum heights of markings for tyres with nominal rim diameter codes ≥ 20 and nominal section width ≤ 235 and for tyres with nominal rim diameter codes < 20 and nominal section width > 235. In addition, the proposal aligns the table on minimum marking heights to correspond with the related figure by using lowercase letters to denote dimensions in both (currently, the figure uses lowercase, but the table uses uppercase).

Proposal to

1. change measurement units for drum speed in Annex 7 from min^-1 to km.h^-1 to align the requirements with other tyre regulations;
2. correct wording from “speed category symbol” to “speed symbol” (as defined in para. 2.33);
3. correct wording from “load capacity index” to “load index” (as defined in para. 2.32);
4. correct a reference to para. 3.2.13. of the Regulation in Annex 7, Appendix 1;
5. correct a boundary value of load index in Annex 7, Appendix 1;
6. delete in paragraph 2.1 in Annex 7, the possibility to use the 2.0 m drum diameter to perform the endurance test; and
7. align the text of Annex 10 with Annex 7 of UN R117 pursuant to the adoption of Supplement 5 to the 02 series of amendments to that regulation.

Proposal for a new UN Regulation based upon the provisions for tyre-pressure monitoring systems (TPMS) extracted from UN R64 in order to facilitate the application of UN R64 within the International Whole Vehicle Type Approval system. This proposal also seeks to take into account efforts to update US FMVSS requirements for TPMS.

Revised version of document GRRF/2016/4, proposing to extract tyre pressure monitoring systems from UN R64, pursuant to the discussions held during the February 2016 GRRF session.

Revised version of document GRRF/2016/5, proposing a new UN Regulation based upon provisions for tyre pressure monitoring systems extracted from the current UN R64, pursuant to the discussions held during the February 2016 GRRF session.

Revised version of document GRRF/2016/9 pursuant to discussions held during the February 2016 GRRF session, proposing a new UN Regulation on tire installation for use within the International Whole Vehicle Type Approval system.

Revised version of the proposal, updated by the GRRF secretariat to take into account comments received during the February 2016 GRRF session, for a revised new UN Regulation based on the provisions for tyre-pressure monitoring systems (TPMS) extracted from UN R64 in order to facilitate the application of UN R64 within the International Whole Vehicle Type Approval system. This proposal also seeks to take into account efforts to update US FMVSS requirements for TPMS.

A complete and comprehensive review of the UN R0 base document for the 19th SGR0 meeting performed by experts from OICA.

Overview of discussions for the future development of vehicle noise regulations prepared by the GRB secretariat.

Review of work towards adapting and/or approving certain UN Regulations for use within the International Whole Vehicle Type Approval regulation.