Request to maintain in the Compendium of Candidates Listing Number 13 –United States of America Environmental Protection Agency and National Highway Traffic Safety Administration, Department of Transportation, Program for Revisions and Additions to the Motor Vehicle Fuel Economy Label – New Fuel Economy and Environment Labels for a New Generation of Vehicles.

Proposal for the Phase 2 development of GTR No. 13, including

1. Further consideration of items in the original authorization (document WP.29/AC.3/17);
2. Potential revision of the scope to address additional vehicle classes;
3. Requirements for material compatibility and hydrogen embrittlement;
4. Requirements for the fueling receptacle;
5. Evaluation of performance-based test for long-term stress rupture proposed in Phase 1 (including assessment of a procedure to evaluate the risk of long-term stress rupture of storage containers made from composite fiber reinforced polymers);
6. Consideration of research results reported after completion of Phase 1 – specifically research related to electrical safety, hydrogen storage systems, and post-crash safety;
7. Consideration of 200 per cent Nominal Working Pressure (NWP) or lower as the minimum burst requirement; and
8. Consider Safety guard system for the case of isolation resistance breakdown.

Proposal to

1. insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources,
2. update the Conformity of Production (CoP) requirements,
3. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
4. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
5. introduce editorial improvements to the requirements for markings,
6. refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources, and
7. removes the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s).

Proposal to clarify the Conformity of Production requirements.

Proposal to

1. insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources,
2. update the Conformity of Production (CoP) requirements,
3. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
4. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
5. to introduce editorial improvements to the requirements for markings,
6. remove the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s), and
7. refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources.

Proposal to clarify the definition of “type”, with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings.

Proposal to

1. insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources,
2. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
3. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
4. introduce editorial improvements to the requirements for markings,and
5. remove the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s).

Proposal to clarify the definition of “type”, with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings.

Proposal to update the Conformity of Production (CoP) requirements and to reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86.

Proposal to update the Conformity of Production (CoP) requirements.

Proposal to

1. insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources,
2. update the Conformity of Production (CoP) requirements,
3. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
4. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
5. introduce editorial improvements to the requirements for markings,
6. remove the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s),
7. refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources.

Proposal to

1. insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources,
2. update the Conformity of Production (CoP) requirements,
3. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
4. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
5. introduce editorial improvements to the requirements for markings, and
6. remove the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s).

Proposal to

1. insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources,
2. update the Conformity of Production (CoP) requirements,
3. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
4. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
5. introduce editorial improvements to the requirements for markings,
6. remove the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s), and
7. refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources.

Proposal to

1. amend the provisions concerning the heat test requirements for Conformity of Production (CoP),
2. complete the deletion of distributed lighting systems (DLS) (light generators) from the regulations,
3. update the general CoP requirements,
4. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
5. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
6. introduce editorial improvements to the requirements for markings,
7. amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45,
8. remove the HV measurement point from the photometric stability requirements for the passing beam (HV measurement point remains valid for the driving beam),
9. clarify the photometric performance requirements, particular with reference to the movement of the cut-off line, during the heat test, and
10. harmonize requirements across Regulations Nos. 19, 98, 112, 113 and 123.

Proposal to add a new paragraph 3.6.2.4. to UN R99 in order to clarify how the run-up of dual-level high-intensity discharge (HID) light sources, as e.g. D9S, should be tested during type approval. In addition, the proposal renumbers the part of 3.6.2.2. that applies to gas-discharge light sources containing black stripes as 3.6.2.3. to make the distinction with gas-discharge light sources not containing black stripes.

Proposal to reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86, clarify the definition of “type”, with regard to manufacturer, trade names and marks, and to introduce editorial improvements to the requirements for markings.

Proposal to

1. amend update the Conformity of Production (CoP) requirements, including the provisions concerning the heat test requirements,
2. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
3. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
4. introduce editorial improvements to the requirements for markings,
5. correct errors in the references to “left-hand traffic” and “right-hand traffic” in the text and associated diagrams of Annex 2,
6. correct an inconsistency between the regulation text and Figure B of Annex 3,
7. amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45,
8. remove the HV measurement point from the photometric stability requirements for the passing beam (the HV measurement point remains a valid for the driving beam),
9. clarify the provisions for the stability of photometric performance during the heat test, with particular reference to the movement of the cut-off line, and
10. harmonize related requirements across Regulations Nos. 19, 98, 112, 113 and 123.

Proposal, subject to endorsement by the GRPE during its January 2017 session, to permit Contracting Parties applying UN R83 and GTR No. 15 (WLTP) to refuse type approvals granted under UN R83 as an alternative to compliance with their national/regional legislation from the date of entry into force of Supplement 9 to the 06 series of amendments to UN R83.

Proposal, subject to endorsement by the GRPE during its January 2017 session, to permit Contracting Parties applying UN R83 and GTR No. 15 (WLTP) to refuse type approvals granted under UN R83 as an alternative to compliance with their national/regional legislation from the date of entry into force of Supplement 5 to the 07 series of amendments to UN R83.

Proposal, subject to endorsement by the GRPE during its January 2017 session, to permit Contracting Parties applying UN R101 and GTR No. 15 (WLTP) to refuse type approvals granted under UN R101 as an alternative to compliance with their national/regional legislation from the date of entry into force of Supplement 7 to the 01 series of amendments to UN R101.

Proposal to:

1. correct provisions on bend lighting for motorcycles adopted by WP.29 as Supplement 2 (document WP.29/2012/83),
2. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
3. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
4. introduce editorial improvements to the requirements for markings,
5. amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45,
6. clarify the test cycle with regard to the stability of photometric performance during the heat test, with particular reference to the movement of the cut-off line, and
7. harmonize related requirements across Regulations Nos. 19, 98, 112, 113 and 123.

Proposal to:

1. insert provisions for the use of incandescent light sources in the case of light source modules and lamps with non-replaceable light sources,
2. update the Conformity of Production (CoP) requirements,
3. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
4. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
5. introduce editorial improvements to the requirements for markings,
6. remove content in paragraph 7.5 that should have been deleted when the text was moved to Annex 3, paragraph 3.3. (via Supplement 4 to the 01 series),
7. remove the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s), and
8. refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources.

Proposal to:

1. reference the compliance requirements for installation contained in Regulations Nos. 48, 53, 72 and 86,
2. clarify the definition of “type”, with regard to manufacturer, trade names and marks,
3. introduce editorial improvements to the requirements for markings,
4. amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45,
5. remove the HV measurement point from the photometric stability requirements for the passing beam (the HV measurement point remains a valid for the driving beam),
6. correct the omission of certain changes from E_max to I_max from the 01 series of amendments that converted the photometric requirements from illuminance E (lux) to luminous intensities I (cd),
7. amend Annex 3, Table 2 to allow sub-classes of Class C to lower the cut-off position to allow for adjustment during foggy road conditions,
8. clarify the test cycle with regard to the stability of photometric performance during the heat test, with particular reference to the movement of the cut-off line, and
9. harmonize related requirements across Regulations Nos. 19, 98, 112, 113 and 123.

Proposal to correct mistranslation of the original English into the Russian version of the text. In the English text, paragraph 2.2.27 of Annex 12 uses the word “travel”. The corresponding word in Russian language should be “ход”. The proposal is aimed at ensuring that the English and Russian texts are equivalent.