Proposed corrections to the original proposal to align UN R105 with ADR 2017.

Proposal to specify that “handrails and handholds at doorways where the associated residual space is not designated for passengers positioned for travel, and where intrusion into the space presents no risk of contact with passengers, shall also be ignored.”

Proposal to insert new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur.

Presentation on cybersecurity issues and ISO 26262 (functional safety of electronic systems).

Proposal to amend document GRSG/2016/2 by replacing paragraph 1.2.2. rather than deleting it. Drawing from the recently approved amendment to UN R58 (document GRSG/2015/17), this proposal would amend paragraph 1.2.2. to read, “Vehicles where any LDP (e.g. fixed, removable, foldable, adjustable, etc.) is incompatible with their use on [traffic] roads may be partly or fully exempted from this Regulation, subject to the decision of the Type Approval Authority.”

Updated proposal, revised for clarity, to amend document GRSG/2016/2 by replacing paragraph 1.2.2. rather than deleting it. Drawing from the recently approved amendment to UN R58 (document GRSG/2015/17), this proposal would amend paragraph 1.2.2. to read, “Vehicles where any LDP (e.g. fixed, removable, foldable, adjustable, etc.) is incompatible with their on-road use may be partly or fully exempted from this Regulation, subject to the decision of the Type Approval Authority.”

Proposal to extend requirements introduced via Supplement 4 to the 04 series of amendments concerning barriers in the gangway and the amount of priority seats to the 05, the 06 and the 07 series of amendments.

Proposal to allow for the use of natural gas refrigeration systems to vehicles propelled by natural gas (CNG or LNG). This proposal addresses a new, environmentally friendly natural gas fuelled refrigeration system for trucks with refrigerated loads that already are propelled by natural gas. Currently paragraph 18.1.7.1 allows heating systems to be fitted on vehicles to heat the passenger compartment and/or the load area of a vehicle, however, the same provision omits cooling systems that are used on trucks for the carriage of loads requiring refrigeration.

Editorial amendment to document GRSG/2016/8 for clarity. The original proposal would allow the use of Class 0 hoses with couplings using sealing technologies other than those with a 45° cone provided that the hose assembly can withstand the impulse test of paragraph 1.7. and the tests of Annexes 5A (overpressure test) and 5B (external leakage test). This proposal clarifies that the original sealing-cone specification or other compliant couplings, including designs with soft seals (e.g., O-ring) provided they pass testing described in Annexes 5D, 5F, and 5G.

Proposal of corrections to document GRSG/2016/7. The wording of the original proposal opens the possible interpretation that the regulation allows materials other than copper, stainless steel, or steel with corrosion-resistant coatings for gas tubes. The intention of the proposal was only to allow for “non-seamless” gas tubing. The original proposal is therefore modified to allow Class 0/I hoses with couplings using gas tubes of other than seamless material.

Proposal from the informal working group on the International Whole Vehicle Type Approval to restructure UN R116 into two separate regulations. The regulation addresses anti-theft, alarm, and immobilizer aspects of theft prevention. Since these aspects may be mandatory or optional depending upon the country or market, the application of UN R116 to whole vehicle type approval becomes problematic. This proposal would extract the immobilizer provisions into a separate new regulation.

Presentation of issues raised during discussions of the GRE Task Force on EMC requirements with regard to the application of several UN Regulations to trolley buses depending upon their configuration (e.g., dual-mode operation either connected to overhead cables or in standard bus mode).

Presentation on blind-spot accident data and work on the development of a test cycle to assess the effectiveness of blind-spot countermeasures to reduce the risk of VRU collisions.

Proposal to amend GRSG/2015/36 introducing requirements for the operation of a CNG heater when the vehicle is stationary and before starting the engine. The limitation on the number of valves used to operate the CNG combustion heater will require technical changes without any significant benefit. The proposal therefore deletes the limitation and introduces additional clarifications.

Proposal to change the latency for scanning a field of vision (total process of scanning, rendering and reset to its initial position) from a maximum of 2 seconds to a maximum of 200 ms. This proposal corresponds to the current state of technology and removes a contradiction within the regulation between paragraphs 6.2.1.2. and 6.2.2.3.4.3. (the latter introduced via supplement 2 to the 04 series of amendments).

Copy of the proposal by Poland to amend UN R55 to ensure that coupling devices are only approved for use on vehicles approved for towing trailers.

Draft proposal to introduce amendments on a procedure to dimension coupling equipment for heavy transports through speed reduction.

Draft proposal to introduce amendments on a procedure to dimension coupling equipment for heavy transports through speed reduction.

Proposal to introduce a procedure to identify allowable combinations of performance values DC and V for drawbar coupling equipment.