Proposal to establish uniform provisions for approval of vehicles of categories M₂ or M₃ designed or equipped primarily for carriage of children, requiring physical inspection systems to prevent child occupants being left inside buses and coaches after journey completion. Physical inspection systems shall be engaged when vehicle master control switch is turned off and disarmed via inspection confirmation device located behind rearmost seat. Systems must generate external visual and audible warnings within specified timeframes if not disarmed, with warnings cycling for at least 10 minutes at greater than 60 dB(A) unless system is disarmed or vehicle master control switch is turned on.

Proposal to establish a new UN Regulation on liquefied hydrogen storage systems (LHSS) for hydrogen-fuelled vehicles of categories M₂, M₃, N₂ and N₃, incorporating specifications for the LHSS, specific components including pressure relief devices and shut-off devices, and vehicle fuel system requirements with testing and approval procedures, based on GRSP/2025/41 and GRSP-78-15-Rev.1.

Proposal to insert a new chapter P and paragraphs 247 and 248 establishing that supply lines for additional TPRDs are constructed from metallic materials with further investigation required for other materials in the next phase, and requiring manufacturers to provide handling procedures to ensure supply lines will not suffer damage or contamination during handling with removal from service of lines with unacceptable damage, exclude the drop test from the requirements at para. 51., and amend para. 81. (c) (i) to clarify that drop impact testing applies to containers without supply lines and valves with damage to supply lines or valves requiring replacement.

CLIV is developing a new UN Regulation for vehicle categories M1, M2, M3, and N1 in Phase 2. The draft regulation requires visual and audible external warnings upon detection of a child left in a vehicle. Visual warnings use direction indicator lamps flashing in SOS morse code pattern for at least 15 seconds, then off for no more than 30 seconds, repeating for at least 10 minutes. Audible warnings must exceed 60dB(A) following the same timing pattern. The IWG requests guidance on potential amendments to UN R48, UN R28, and UN R165.

Five documents propose amendments to UN R46 series 02-07 to align requirements with UN R26 and UN R61, particularly regarding soft parts of camera monitoring systems and mirrors based on Shore A hardness. The 05 series introduced alignment requirements; harmonization is proposed for earlier series with existing approvals.

The agenda of the 4th meeting of Task Force 4 Frontal Impact & Restraint System Requirements includes a review of the progress dashboard, presentations of updated studies on abdominal injuries and rear row, continued discussion on priorities, and planning for a workshop in Japan.

The task force discussed assessment of Human Body Model (HBM) readiness timelines, adding skull fractures, lumbar spine, and general kinematics to evaluation criteria. The group identified injury metrics and data gaps for each body region. TU Graz will gather additional stakeholder feedback. The next meeting is scheduled for 13 April 2026.

The group will receive comments on the draft UN Regulation for buses and coaches, covering definition order, operation isolation of the physical inspection system, vehicle master control switch definition, transitional provisions, type approval tests, and paragraph 5.4.4.6.2. The agenda includes feedback on a proposal made to GRSG and discussion of the September meeting location.

Proposal to enable application to vehicles of category X (vehicles of category Y are not in scope) with amendments addressing steering wheel hub provisions, cab positioning, and seating requirements for vehicles of category X. Cabs for vehicles of category X mounted in other positions than vehicle front shall not be taken into account for frontal collision simulation.

Proposal based on GRSP/2025/31 to amend para. 7.1.3.6. to require relevant intermediate dummies testing when Enhanced Child Restraint Systems require substantial modification for different sizes or when size range covers more than 3 size ranges and to delete paragraph 5.5. and renumber paragraphs 5.6. to 5.8. as 5.5. to 5.7.

Proposal to modify para. 6.2.1.1. regarding insert layers for small babies with stature below 50 cm, amend Annex 18, table 1 with updated shoulder height dimensions for statures 40 cm to 70 cm, update approval markings in Annex 2, and introduce transitional provisions with Contracting Parties no longer obliged to accept preceding series approvals from 1 September 2028.

Proposal to amend Annex 3, table 3, column “Number of cycles,” first row, is amended to read “60 per cent of initial cycle life (11 000 cycles).” and Annex 3, table 4, column “Number of cycles,” first and second rows, is amended to read “20 per cent of initial cycle life (11 000 cycles).”

Proposal to extend UN R134 to vehicles of category X (excluding vehicles of category Y), add provisions for Periodic Technical Inspections, modify hydrogen concentration warning requirements for ADS features of type 2 to transmit logic signals to the ADS, and adjust test cycle specifications in Annex 3.

Proposal to extend the scope to include vehicles of category X, replace “driver” by “occupant”, and separate the scope into vehicles with regard to protection of occupants against the steering mechanism and electrical shock in a frontal collision and steering controls with regard to protection of occupants in the event of impact.

Proposal to enable application to vehicles of category X. For vehicles equipped with an Automated Driving System other than vehicles of category X, in manual driving mode no special provisions apply. In a mode where an ADS feature is active, the relevant requirements for ADS vehicles apply.

Proposal to enable application to vehicles of category X (vehicles of category Y are not in scope). For vehicles of category X, the R point of the most forward passenger seat shall be taken instead of the R-point of the driver’s seat. Amendments address steering control contact requirements and modify occupant references.

Proposal to clarify that Child Restraint Systems approved according to UN R129 or R44 may be used in vehicles of categories M₂ and M₃ with a 3-point belt and/or ISOFIX attachments without further requirements. As a result, Part I of UN R170 covers Built-in Child Restraint Systems for securing children from 40 – 150 cm in forward facing and rearward facing vehicle seats and Part II addresses Child Restraint Systems approved according to UN R129 or R44 which may be installed in a bus seat with a 2-point belt.

Proposal to enable application to vehicles of category X, including prohibition of one-touch closing when an ADSF-2 is active, requirement for auto-reversing devices for power operated windows that can be operated by an ADSF-2, and user manual instructions for power-operated systems including warnings regarding improper use and driver and ADS responsibilities.

Proposal to amend UN R17, including revised definitions of head restraint, corrections to paragraph references, replacement of terminology such as “absorption” with “dissipation” and “reference line” with “longitudinal vertical plane passing through the R-point,” revised test procedures in multiple annexes, and modifications to measurement requirements for head restraint displacement and strength testing. The text was adopted by GRSP at its seventy-eighth session based on ECE/TRANS/WP.29/GRSP/78, Annex IV.A. Amendments

Proposal to enable application to vehicles of category X, including attention to ADAS/ADS sensors and providing specifications for test procedures and dummy positioning requirements for vehicles of category X in frontal collision protection testing.

A design is intuitive when users understand and use it correctly and efficiently without needing instructions or prior training. Key signs include matching user expectations, requiring little explanation, giving clear feedback, minimizing thinking, maintaining consistency, and building on familiar patterns. For emergency door opening, intuitive design requires interior release control to unlock doors and unlatch without separate controls. Alternative actions for power loss must be fully intuitive, integrated or in close vicinity, within reach, and properly marked. Exterior door handles need a proper force application area for at least four fingers of an adult hand.