Status report on efforts to resolve concerns related to automatic headlamp leveling provisions and their impact on visibility and on-coming driver glare.

After examination of the draft revision of UN Regulation 86 (document GRE/2014/2), the Italian experts believe it necessary to make six further changes, including definition of “textured lens” and clarifications of certain paragraphs.

Document GRE/2013/62 concerning electronic light source control gear proposed to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. The objective of this proposal is to restrict the voltage at headlamps equipped with (halogen) filament lamp light sources in order to avoid excessively high or low (semi-) permanent luminous intensity of the headlamp and consequently shorter lifetime of the halogen light source. This submission takes into account the positions presented in documents GRE/2013/44, GRE/2013/62, GRE-70-17, and GRE-70-34.

Request to extend the work of the AVLI group in order to develop amendments that would apply UN R86 to agricultural trailers and towed machinery.

Updated document to correct the original proposal to introduce the possibility of interdependent lamps for dedicated motorcycle lamps by including an omitted diagram and highlighting the marking clause.

Proposal to introduce flashing side marker lamps for vehicles of categories N₂, N₃, O₃ and O₄. The objective of this provision is to improve the safety of vulnerable road users by better informing them about the intention of a heavy goods vehicle to make a turn. Germany believes this to be a simple measure that will improve the safety level especially for cyclists and pedestrians located in the blind spot area of a heavy goods vehicle.

GTB discussion paper to focus attention on defining the problem(s) to be resolved through a the simplification of UN lighting regulations.

Text originally prepared by Belgium to propose amendments to Regulation No. 107 to align the additional safety prescriptions for trolleybuses (Annex 12) with the corresponding electrical standards (see document GRSG/2013/16). During discussion in the October 2013 session of GRSG, some Contracting Parties felt that the prescriptions for electromagnetic compatibility of trolleybuses belong in Regulation No. 10. So these prescriptions are taken out of the amended proposal (ECE/TRANS/WP.29/GRSG/2014/19) and are proposed here for consideration by GRE for further action.

Document GRE/2013/65/Rev.1 proposes a new class F of marking materials designed with chevron type pattern to be applied to special utility vehicles or trailers not ordinarily covered by standard contour marking materials. The proposal also attempts to harmonize a number of national requirements. Japan, however, prohibits white retro-reflecting materials at the rear of vehicles for safety reasons. Therefore, Japan proposes to clarify that the approval of Class F retro-reflective markings is dependent upon their definition within national regulatory requirements.

Presently, UN R48 requires that reverse lights be switched off when cornering lights are switched off. OICA argues that the simultaneous lightning of both cornering lamps for slow maneuvers in forward motion (e.g., while parking a vehicle) can increase safety by improved illumination of surroundings. Therefore, OICA proposes that cornering lights be allowed to remain on as long as the vehicle speed does not exceed 10 km/h.

Document GRE/2014/13 proposes to ensure that the introduction of the new class F marking materials does not conflict with the mandatory requirements for existing class C materials. The addition of Class F brings markings required under certain countries’ national legislation within the UN regulatory system. However, Japan actually prohibits the use of white retro-reflective markings on the rear of vehicles. Therefore, Japan proposes the addition of a footnote confirming the right of Contracting Parties to prohibit the use of Class F markings under national legislation.

Proposal to delete the requirement that the total objective luminous flux of all LED modules producing the principal passing (main low) beam of a headlamp be greater than or equal to 1000 lumens. France argues that the requirement is design-restrictive, unnecessary given the objective criteria for luminous output and photometric grid points of the regulation, and obsolete given improvements in LED technologies.

The International Whole Vehicle Type Approval system under development would allow for a limited recognition approval to earlier versions of UN Regulations. Since this limited IWVTA requires Contracting Parties to declare to which version of each regulation they adhere, this proposal would amend the “Status of the 1958 Agreement” (document WP.29/343) to include this information as part of the regular process of reporting on the status of UN Regulations.

OICA-proposed revisions to the draft Q&A document intended to help explain the international whole vehicle type approval system and the proposed “UN Regulation No. 0” (document SGR0-08-06).

Proposal to delete the requirement that the total objective luminous flux of all LED modules producing the principal passing (main low) beam of a headlamp be greater than or equal to 1000 lumens. France argues that the requirement is design-restrictive, unnecessary given the objective criteria for luminous output and photometric grid points of the regulation, and obsolete given improvements in LED technologies.

In document GRE/2014/7, IMMA proposed to introduce the possibility of interdependent lamps for dedicated motorcycle lamps as Supplement 17 to Regulation No. 50. The concern was that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features. In this document, India proposes to clarify that the installation height of the device must be less than or equal to 750 mm.

In document GRE/2014/9, IMMA proposed the use of different brake lamp activation methods and the introduction of high-mounted stop lamps to improve the conspicuity of “powered two-wheelers” under Regulation No. 53. In this document, India offers a number of editorial recommendations.

Brief presentation raising question over the necessity to have triangular reflectors on the rear of large trailers and seeking greater flexibility in such rear reflectors.

Final proposed text to revise and update the 1958 Agreement pursuant to the project to establish an international whole vehicle type approval system.