Proposal to introduce options for fulfilling the marking requirements of E-marking to avoid redundancy with other UN Regulations and to permit a smaller E-marking (as currently permitted under UN R67 and R158).

Proposal to introduce options for fulfilling the marking requirements of E-marking to avoid redundancy with other UN Regulations and to permit a smaller E-marking (as currently permitted under UN R67 and R158).

Proposal to update the references to the three-dimensional H-point (3-D “H”-point) measurement and calibration procedure pursuant to the update of the device specifications and transfer from the Consolidated Resolution on the Construction of Vehicles (R.E.3) to Mutual Resolution No. 1 (M.R.1).

Proposal to introduce options for fulfilling the marking requirements of E-marking to avoid redundancy with other UN Regulations (as currently permitted under UN R107) and to permit a smaller E-marking (as currently permitted under UN R67 and R158).

Proposal to introduce options for fulfilling the marking requirements of E-marking to avoid redundancy with other UN Regulations (as currently permitted under UN R107) and to permit a smaller E-marking (as currently permitted under UN R67 and R158).

Proposal to introduce options for fulfilling the marking requirements of E-marking to avoid redundancy with other UN Regulations (as currently permitted under UN R107) and to permit a smaller E-marking (as currently permitted under UN R67 and R158).

Proposal to introduce options for fulfilling the marking requirements of E-marking to avoid redundancy with other UN Regulations (as currently permitted under UN R107) and to permit a smaller E-marking (as currently permitted under UN R67 and R158).

Proposal to introduce options for fulfilling the marking requirements of E-marking to avoid redundancy with other UN Regulations (as currently permitted under UN R107) and to permit a smaller E-marking (as currently permitted under UN R67 and R158).

Discussion paper on automatic fire suppression systems for the compartment where the internal combustion engine propelling the vehicle related to the risk of Boiling Liquid Expanding Vapor Explosion.

Proposal to clarify the meaning of “set pressure” and its application in the requirement to ensure that the primary LNG relief valve does not open below 1.5 MPa.

Proposal to clarify that all speedometers and/or odometers installed on a vehicle in the case of more than one shall comply with the requirements of UN R39.

Proposal to clarify that high capacity vehicles and vehicles with competing objectives do not have to meet the requirement for the Subsection Frontal Visible Volume (SFVV), to describe how the SFVV should be calculated to take account of the reduced volume for vehicles with narrower cab designs, and to revise and correct the transitional included in document GRSG/2024/6.

Proposal from the task force on UN R39 Mileage Accuracy to amend and supplement the existing requirements for odometers to include provision on:

• accuracy of the on-board odometer mileage values,
• anti-tampering of the on-board odometer mileage values,
• accuracy and anti-tampering of the odometer mileage values displayed to the driver.

Proposal to update the references to the three-dimensional H-point (3-D “H”-point) measurement and calibration procedure pursuant to updates and transfer of related provisions from the Consolidated Resolution on the Construction of Vehicles (R.E.3) to Mutual Resolution No. 1 (M.R.1).

Proposal to update the references to the three-dimensional H-point (3-D “H”-point) measurement and calibration procedure pursuant to updates and transfer of related provisions from the Consolidated Resolution on the Construction of Vehicles (R.E.3) to Mutual Resolution No. 1 (M.R.1).

Proposal to update the references to the three-dimensional H-point (3-D “H”-point) measurement and calibration procedure pursuant to updates and transfer of related provisions from the Consolidated Resolution on the Construction of Vehicles (R.E.3) to Mutual Resolution No. 1 (M.R.1).

Proposal to update the references to the three-dimensional H-point (3-D “H”-point) measurement and calibration procedure pursuant to updates and transfer of related provisions from the Consolidated Resolution on the Construction of Vehicles (R.E.3) to Mutual Resolution No. 1 (M.R.1).

Proposal to specify the requirements for the headform test. This test should not be mandatory for vehicles where the protection of the occupant’s head is not achieved by the glazing itself, rather by a restraint system or other means.

Proposal to amend UN R125 pursuant to the establishment of a new UN Regulation on Field of Vision Assistant. This document includes the update to the references to the three-dimensional H-point (3-D “H”-point) measurement and calibration procedure pursuant to the updates and transfer of relevant provisions from the Consolidated Resolution on the Construction of Vehicles (R.E.3) to Mutual Resolution No. 1 (M.R.1).