Proposal to add injury criteria in relation to the neck bending moment along the lateral axis (not to exceed 57 Nm when stretched), clarify the distance between the seats to align with IN R107, and annulation of the proposal to delete paragraph 2.1.2 because the scope of UN R80 provides for testing of seats for vehicles of M₂ and M₃ categories of II, III and B classes where approval is allowed via testing without a vehicle and mounted rigidly on a test platform.

Proposal to address new active suspension technologies that can raise the height of the vehicle in motion up to a defined speed. Since the vehicle height has an influence on the headform test area (WAD) and on the test results for legform tests, all possible vehicle heights up to a driving speed of 11.1 m/s (40 km/h) should be considered to be relevant for the impact with a pedestrian. The proposal is a clarification on this issue.To ensure that such an active suspension system is considered for type approval, there should be a detailed description in the information document. Due to the fact that extensions for an existing vehicle type concerning UN Regulation No. 127 are still possible according to 00 and 01 series of amendments, the proposal is relevant for all series of amendments of the UN R127.

Revised proposal (superseding GRSP-63-24) to clarify the possibility to install side-facing seats in buses of category M₂ and M₃ of classes A and I.

Proposal to delete Appendix 5 as a basis for type approval and thereby end static testing as a compliance option.

Proposal to amend Appendix 1 by reducing the forward movement of the head of the manikin to 1.2 m in alignment with UN R14. The proposal would also limit the movement of the seat anchorages to 100 mm to ensure a minimum residual space for the passenger between the seats. Lastly, to ensure that seat fixations are reliably fastened after relocation, the proposal would require the necessary information to be marked directly on the seat and provided in the owner’s manual.

Proposal to explicitly state that functional safety requirements apply to categories of vehicles beyond M₁.

Proposal to clarify the application of GTR 7 Phase 2 static alternative provisions and to modify the allowed range of tolerances under the backset retention and energy dissipations test.

Presentation on Italy’s National Law No.117 of 1 October 2018 which makes the use systems to prevent children from being left unattended in vehicles mandatory from 1 July 2019 for M₁, N₁, N₂, and N₃ vehicles.

Proposal to clarify the use of the i-Size logo on i-Size boosters.

Labels under UN R129, paragraph 4.5. highlight that the ECRS should not be used by children under 15 months old. This proposal presents the same layout for rearward/forward-facing and for forward-only CRS.

Proposal to specify that, in the case of an infant carrier, the dummy shall be restrained in the Enhanced Child Restraint System before it is installed on the test bench.

Proposal to specify the dimensions of the approval number, correct term from " Regulation No. 129-02" to “UN Regulation No. 129/02”, and change the 145 cm stature of the Specific Vehicle Booster seat to the 150 cm stature as this is the upper limit.

Proposal to specify usage requirements for unfixed CRS inserts.

Proposal to cease new CRS approvals under UN Regulation No. 44 as of [1 September 2020], including amended transitional provisions.

Proposal to introduce a new measurement procedure for the effective height of the head restraint and introduction of the Biofidelic Rear Impact Device (BioRID). This proposal eliminates the backset measurement test procedure using the HRMD method.

Proposal to clarify that Conformity of Production assessments shall be conducted under the same requirements as those of the original approval or, if applicable, the extension of the approval. This proposal supersedes the proposal to require testing of Integral ISOFIX ECRS to use the door panel geometry of the 00 series of UN R129 (document GRSP/2018/31).

Proposal to introduce provisions for the booster cushion category of child restraint systems under UN R129.

Report on CLEPA assessments of the proposed GTR 7 Phase 2 BioRID criteria.

Proposal from the Informal Working Group (IWG) on Global Technical Regulation No. 9 Phase 2 (GTR9-PH2) to introduce the Flex PLI lower legform impactor and related test procedures into the GTR on pedestrian safety protection, including new bumper test area specifications.

Appendix to the proposal for Amendment 2 to GTR 9 providing the rationale, justifications, and other supplemental information concerning the development of the amendment to introduce the Flex PLI lower legform impactor and related test procedures, including new bumper test area specifications.

Proposal to require seat belt components such as retractors to remain functional if damaged during the load-retention test according to Annex 9 of UN R17. Such components have occasionally been damaged during testing such that their functionality has been impaired. In order to ensure adequate occupant safety, this proposal would require all safety-belt components to be included in the test installation and require post-test inspection to confirm the continued functionality.

Proposal to introduce installation specifications for securing a cab mounted on a vehicle to the test rig for tests B and C, as is currently provided for test A, under UN R29. This proposal aims to improve repeatability and reproducibility while allowing more flexibility in permitting the use of rigid composite blocks and/or (adjustable) metal brackets in securing the vehicle in the place of the wooden block presently prescribed in Figure 1.

Proposal to require checking of non-integral child restraints (e.g., booster seats) for risk of injuries caused by narrow contact with buckle and safety-belt such as may be caused by strong local pressure from twisted buckles, belts, or tongues.

Proposal to amend the transitional provisions in order to explicitly confirm that approvals granted prior to the respective supplements to the 01 and 02 series of amendments and the establishment of the new guidelines on UN Regulation procedures (documents WP.29/2017/107 including Corrigendum 1 and Addendum 1) will continue to be accepted. This amendment confirms the understanding that the new procedures apply only to new approvals and do not affect previous approvals.

Proposal to add provisions for the definition and requirements for lower tether strap and the definition and specifications of Lower Tether Anchorages (LTA).

Alternative proposal to GRSP/2017/27 submitted by the EC to clarify and improve airbag warning label requirements and to group these provisions under UN R16 in order to avoid the need to update multiple regulations in case of changes. OICA would not, however, add provisions concerning language variations (these are handled at the point of sale).

Proposal to delete Appendix 5 and thereby end static testing as a compliance option. In addition, this proposal amends Appendix 1 by reducing the forward movement of the head of the manikin to 1.2 m in alignment with UN Regulation No. 14. Further, the proposal would limit the movement of the seat anchorages to 100 mm to ensure a minimum residual space for the passenger between the seats. Lastly, to ensure that seat fixations are reliably fastened after relocation, the proposal would require the necessary information to be marked directly on the seat and provided in the owner’s manual.

Proposal to amend the transitional provisions in order to explicitly confirm that approvals granted under the preceding series of amendments and the establishment of the new guidelines on UN Regulation procedures (documents WP.29/2017/107 including Corrigendum 1 and Addendum 1) will continue to be accepted. This amendment thus confirms the understanding that the new procedures apply only to new approvals and do not affect previous approvals.

Proposal prepared by the secretariat to correct and improve the quality of the image of Figure 1a of Annex 5.

Proposal from Spain on behalf of the Technical Services Group (TSG) on UN R129 to require that the shoulder strap positioner, if any, and the buckle open independently of each other in order to satisfy the requirement that the buckle can be opened by a single action. Currently, if the shoulder strap positioner has not been opened, it is possible that the buckle cannot be opened.

Proposal from Spain on behalf of the Technical Services Group (TSG) on UN R129 to require that the shoulder strap positioner, if any, and the buckle open independently of each other in order to satisfy the requirement that the buckle can be opened by a single action. Currently, if the shoulder strap positioner has not been opened, it is possible that the buckle cannot be opened.

Proposal from Spain on behalf of the Technical Services Group (TSG) on UN R129 to require that the shoulder strap positioner, if any, and the buckle open independently of each other in order to satisfy the requirement that the buckle can be opened by a single action. Currently, if the shoulder strap positioner has not been opened, it is possible that the buckle cannot be opened.

Proposal from Spain on behalf of the Technical Services Group (TSG) on UN R129 to require that the shoulder strap positioner, if any, and the buckle open independently of each other in order to satisfy the requirement that the buckle can be opened by a single action. Currently, if the shoulder strap positioner has not been opened, it is possible that the buckle cannot be opened.

Proposal from Spain on behalf of the Technical Services Group (TSG) on UN R129 to restrict iSize booster seats (Non-integral Enhanced Child Restraint Systems) to occupants with a maximum stature of 135 cm in order to satisfy the plug and play principle. Presently, UN R129 would allow for approval of such CRS for children up to 150 cm.

Proposal from Spain on behalf of the Technical Services Group (TSG) on UN R129 to restrict iSize booster seats (Non-integral Enhanced Child Restraint Systems) to occupants with a maximum stature of 135 cm in order to satisfy the plug and play principle. Presently, UN R129 would allow for approval of such CRS for chiildren up to 150 cm.

Proposal from Spain on behalf of the Technical Services Group (TSG) on UN R129 to allow the head of the dummy to pass the DE plane provided there is a structure (e.g., head pad or backrest) that provides adequate protection for the head. Under UN R129, the combination of a stiffer test bench foam and the design of the test dummy can mean that when testing forward-facing child restraints (including boosters), the dummy’s head often passes the DE plane. The Q-series dummies are not proven to be biofidelic during the rebound phase of the impact test. In such cases, the head pad or backrest provides protection to the child’s head and the energy-absorption properties of this structure will have been tested using the test method described in UN Regulation No. 129.