Proposal discussing the need for addition of an objective test procedure for post-crash testing and improvement in currently described subjective HF audio
assessment procedure.

Proposal for AECS compliance validation based on ITU-T P.1140.

One of the outcomes of the work on updating UN R55 was the recognition that agricultural couplings present a set of challenges distinct from other vehicles. This revised proposal takes into account comments received during the February 2016 GRRF session for the establishment of an informal working group to develop a new regulation (UN R55-A) to respond to the specific needs of agricultural vehicle couplings.

Revised proposal to ensure that coupling balls do not block rear lighting and/or registration plates. In line with the EU General Safety Rule, Annex IV specification for application of UN R55, couplings that might block lighting or plates must be removable, repositionable, and unlockable in order to make it easier for users to remove them or reposition them when not in use (e.g., towing a trailer.) Coupling balls that are so designed as to be unable to block lighting or plates may still incorporate locks and/or require tools to remove or reposition.

Proposal to transfer electrical safety provisions for trolleybuses (Annex 12) from UN R107 to UN R100. In 2006, the provisions of UN R36, UN R52, and UN R107 were merged through the 02 series of amendments to UN R107. In 2015, Annex 12 of UN R107 was amended to align additional safety prescriptions for electrical safety of trolleybuses with the corresponding electrical standards. However, UN R100 has evolved beyond its initial focus on battery electric vehicles and currently presents a more appropriate location for maintaining the trolleybus electrical safety provision of Annex 12. For the provisions of Annex 1 – Part 1 – Appendices 1, 2 and 3, where a list of characteristics of a trolleybus was added apart from the special environmental conditions, a reference will be inserted to Annex 6 – Part 1 and Annex 7 of UN Regulation No. 100. A corresponding proposal for amendments will be submitted as an official document to the Working Party on Passive Safety.

Proposal to harmonize UN R110 with standard ISO 11439:2013 on high pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles.

Proposal to allow the use of Class 0 hoses with couplings using sealing technologies other than those with a 45° cone. Currently, non-seamless double and single wall tubes are used in brake and fuel tubing applications, allowing for the use of a variety of end forms and coupling techniques. Provided the hose assembly can withstand the impulse test of paragraph 1.7. and the tests of Annexes 5A (overpressure test) and 5B (external leakage test), such configurations should be permitted under UN R67 in order to remove an unwarranted design restriction. In cases where a soft seal body (e.g. O-ring) is used, the compatibility of the material with use conditions must be demonstrated by testing according to Annexes 5D (CNG/LNG compatibility test), Annex 5F (resistance to dry heat) and Annex 5G (ozone aging).

Proposal to correct a typographical error in paragraph 7.1. where the reference should be to paragraph 8.22 rather than 8.21, to remove a duplicate and contradictory reference in Annex 4A to the requirements of Class 1 pressure relief valves, and to align paragraph 2.2. of Annex 4H with paragraph 18.6.1.2. limiting the delay in switching-off of the automatic valve after stalling of the engine to two seconds (rather than five as presently in the text).

Proposal to include the liquefied natural gas (LNG) fuel connector provisions as specified in ISO 12617:2015.

At the May 2015 Type Approval Authorities Meeting (TAAM), Poland raised concerns (attached with this submission) over small M₁ vehicles being equipped with aftermarket coupling devices where the vehicle in question is not designed for towing a trailer. In effect, these vehicles are not permitted to tow trailers, but are nonetheless enabled to be equipped for such a purpose by the aftermarket devices. Therefore, Poland proposes to amend UN R55 to ensure that coupling devices are only approved for use on vehicles approved for towing trailers.

Proposal to clarify the scope and the application of the regulation. The proposal clarifies that the regulation applies to “the burning behaviour of electric cables and cable sleeves or cable conduits used in the vehicle” and it updates the reference to paragraph 5.22. of ISO 6722-1:2011. Specifically, the proposal would apply testing to electric cables, cable sleeves, and cable conduits that exceed a length of 100 mm.

Proposal to allow the use of Class 0 hoses with couplings using sealing technologies other than those with a 45° cone. Currently, non-seamless double and single wall tubes are used in brake and fuel tubing applications, allowing for the use of a variety of end forms and coupling techniques. Provided the tubing can withstand the applicable tests according to Annex 15, Table 1, such configurations should be permitted under UN R67 in order to remove an unwarranted design restriction.

Proposal to expand the scope of the regulation by deleting paragraph 1.2.2. which allows for the exclusion of “vehicles designed and constructed for special purposes where it is not possible, for practical reasons, to fit lateral protection devices” from the text. The UK submits that paragraphs 13 and 16 of the regulation provide specific provisions that address this situation whereas the exclusion clause allows for a broader interpretation that unnecessarily limits the use of lateral protection devices. Moreover, exemptions may still be accorded at the national level.

Review of work towards adapting and/or approving certain UN Regulations for use within the International Whole Vehicle Type Approval regulation.

WP.29 adoption of the new IWVTA regulation (UN Regulation No. 0) is anticipated for March 2017 with an entry-into-force the following October. This initial regulation (00 series of amendments) will include UN Regulations as they stand prior to September 2, 2017. However, a number of these regulations contain transitional provisions such that new versions will enter into force during the 12 months following this cut-off date. Therefore, this document proposes a list of such regulations that would be included in the 01 series of amendments to UN R0 to be submitted for adoption by WP.29 in November 2017. In concept, UN R0 would be updated with these “upgraded” versions of the UN Regulations.

Proposal for testing of panoramic sunroof glass ceramic printed area (CPA).

Reproduction of the proposal submitted to GRSG in order to clarify the intended scope of the regulation and to align the drop ball test language with that of UN Regulation No. 43 and ISO ISO 3537.