Proposal from the IWVTA informal group.

Proposal for a new regulation to consolidate the current light-signalling regulations from the informal group on the Simplification of Lighting Regulations.

Summary of amendments under development within the GRE Task Force on Electromagnetic Compatibility.

SLR informal group working draft for a new UN Regulation on light-signalling devices (LSD) to consolidate existing regulations related to light-signalling as part of the program for the simplification of lighting regulations.

Table of regulations and pending proposals that would in whole or in part be consolidated into the new UN Regulation on light-signalling devices.

Proposal to make the fitting of front position lamps optional and allow for its separate control under certain conditions and to allow for rear positions lamps and registration plate lamps to be lit during the period between the activation of the master switch and the engine start.

EMC Task Force consolidated version as of 22 March 2017.

Proposal to:

1. delete paragraphs 6.2.7.6.2. to 6.2.7.6.3.2. concerning transitional provisions for the 05 series of amendments,
2. to clarify that drivers may not switch OFF the dipped-beam headlamps manually when they are switched ON automatically according to paragraph 6.2.7.6.1., and
3. to clarify that daytime running lamps shall not be switched OFF except as specified in paragraphs 6.19.7.1. to 6.19.7.6. (For example, DRLs shall not be switched OFF when only the position lamps are ON.).

Proposal to introduce the following changes into the draft new Regulation on light-signalling devices:

1. Use of LED substitute light source(s) is allowed and does not constitute a change of the lamp type. However, lamp performances shall be tested during type approval also with the LED substitute light source. Approval of the lamp using filament light source(s) is a prerequisite for approval of the lamp using LED substitute light source(s).
2. COP testing of the lamp is required with an (etalon) filament light source only, because the LED substitute is the counterpart light source of the filament light source, resulting in equivalent photometrical lamp performance. The quality i.e. the equivalence to the filament light source, is controlled in R128.
3. Use of LED substitute light sources is at the discretion of the applicant, who shall declare this use, if any, to the Approval Authorities at the time of application for the first lamp approval or subsequent extension of approval issued for the version using the LED substitute light source.
4. The use of LED substitute light source(s) in a certain lamp type shall be indicated on the lamp by marking of the LED substitute light source category, in addition to the marking of the filament light source of which the LED substitute light source is the counterpart.
   
   This marking on the lamp will be used for checking the allowance for use of lamps with LED substitute light sources in application of the Regulation on lamps installation on vehicle.
5. In case a lamp with colour filter(s) is approved for using LED substitute light source(s), this lamp shall be marked “G” to indicate that this lamp shall be equipped with LED substitute light source(s) marked “G” for colour and luminous intensity quality reasons.
6. The indication of both the filament light source and of its LED counterpart light source, if any, shall be explicitly provided in the communication form.

During October 2016, GRE-76 adopted collective amendments (GRE/2016/31) to align the requirements of lamp regulations (7, 23, 38, 48, 77, 91 and 119) to guarantee the conformity of the lamp in case of any failure or the mandatory indication that a failure had occurred. This means that when a failure indication signal is provided by the lamp, the vehicle shall be equipped with a tell-tale indicating the failure. Thus, amendments were proposed for Regulation No. 48 to specify the modes of displaying the corresponding failure (see GRE/2016/7). Subsequently, some GRE experts requested GTB to clarify the text of its proposal. This proposal amends UN R48 with respect to all lamps affected by GRE/2016/31 to include the failure indication requirement. The proposal does not apply to the failure indication requirements already in UN R 48 prior to the last (76th) GRE session.

Updated proposal to introduce requirements and test specifications to light emitting diode (LED) forward lighting light sources.

Proposal to clarify that the decision table refers to the worst case situation and to correct a cross-reference.