Updated paper on the grouping of lighting regulations under one of three new regulations as follows:
Light Signaling Devices incorporating Regulations 4, 6, 7, 23, 38, 50, 77, 87, and 91
Forward Lighting Devices incorporating Regulations 19, 98, 112, [ 113 ], 119, and 123
Retro-Reflective Devices incorporating Regulations 3, 27, 69, 70, and 104

Proposal for Supplement 17 to the 04 series of amendments, Supplement 10 to the 05 series of amendments and Supplement 8 to the 06 series of amendments to Regulation No. 48. The proposal seeks to clarify paragraph 6.21.1.2.4. with regard to the application of conspicuity markings on bodywork made of flexible material.

Proposal to further refine the transitional provisions of UN R48. In 2014, the transitional provisions of UN R48 were changed in order to avoid having more than one series of amendments in force at the same time (via Supplement 3 to the 06 series of amendments). This change allows earlier series of amendments to be “frozen” and used under the International Whole Vehicle Type Approval system (IWVTA) as “versions” of UN R48. However, the possibility for the partial application of a series of amendments resulting from the installation of new equipment on a vehicle approved to an earlier series has been raised within the IWVTA. This proposal refines the transitional provisions in order to enable partial application of a series through an extension of the existing approval rather by requiring a new approval. At the same time, the proposal aims to ensure that the safety objectives of UN R48 are met.

Proposal to align the text in the header row of the table in paragraph 6.1 (light emitted by the lamps) with the definitions used in Regulation No. 48 for the installation of “single lamps”, “lamps marked D” and “interdependent lamps”.

Proposal to remove restrictions that impede the use of bend lighting on motorcycles. UN R53 currently prohibits the use of additional lighting units when the driving beam is in use. This requirement unnecessarily restricts the use of ALU to improve road illumination at night when the motorcycle is banking through a turn.

Proposal to clarify the specifications of filament lamp category H19.

Proposal to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required.

Proposal to amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45 where the specified quantity of “2 ± 1 parts by weight” of surfactant results in invalid testing. The correct specification should be “2 ± 1 drops” of surfactant. While GTB notes that the specification should eventually be incorporated differently under the pending simplification of lighting regulations, the organization strongly urges amending UN R45 as quickly as possible.

Compressed file package with three documents outlining the structure for the new simplified lighting regime and for the new regulations on light signaling and road illuminating devices.

Proposal to add a new paragraph 3.6.2.4. to UN R99 in order to clarify how the run-up of dual-level high-intensity discharge (HID) light sources, as e.g. D9S, should be tested during type approval. In addition, the proposal renumbers the part of 3.6.2.2. that applies to gas-discharge light sources containing black stripes as 3.6.2.3. to make the distinction with gas-discharge light sources not containing black stripes.

Proposal to correct the terminology in paragraph 5.7.2.1. for consistency across all requirements and to clarify the language in paragraphs 6.2.9., 6.3.6.1.2.1. and 6.3.6.1.2.2. to promote the correct application of the 2,000-lumen limit.

Paragraph 6.5.3. of UN R48 prescribes the use of specific categories of front direction indicators in relation to their distance from the dipped beam headlamp or front fog lamp. However, the text allows categories 1a and 1b to be used at any distance greater than the minimum prescribed for each of them. The present text of UN R6, Annex 1, however, only allows a specific category to be used in the specific range of distance prescribed. Therefore, this proposal deletes the specific requirements in UN R6 and introduces a direct reference to the requirements in UN R48. This proposal effectively eliminates the need for a lower maximum value for the Category 1 front direction indicator than that of the other categories. Therefore, it is proposed to align the maximum luminous intensity value of Category 1 to that of Categories 1a and 1b.

Proposal to align the text of paragraph 6.1.6. with the definition of “single lamp” introduced by document ECE/TRANS/WP.29/GRE/2014/6 (Proposal for Supplement 14 to the 04 Series of amendments, Supplement 7 to the 05 Series of amendments and Supplement 5 to the 06 Series of amendments of Regulation No. 48). The reference to paragraph 4.2.2.6. in the header of the table in paragraph 6.1. is also corrected.

Supplement 11 to the 02 series of amendments to Regulation No. 7 introduced a new paragraph “0. SCOPE” that included vehicles of category “L”. This proposal corrects the title of the Regulation, removing the exception of motor cycles.

The content of paragraph 7.5. was moved to Annex 3, paragraph 3.3. by supplement 4 to the 01 series of Regulation No. 119. The original content of paragraph 7.5. should have been deleted as part of the amendment, but this was overlooked. This amendment is necessary to remove the current conflict between the content of Annex 3, paragraph 3.3. and paragraph 7.5 in the main text.

When the 01 series of amendments to Regulation No. 123 was introduced to convert the photometric requirements from illuminance E (lux) to luminous intensities I (cd), some changes from E_max to I_max were overlooked. This amendment introduces the necessary corrections. The proposal also amends Annex 3, Table 2 to allow sub-classes of Class C to lower the cut-off position to give the opportunity to adapt to foggy weather conditions and thus avoid glare and increase safety.

This collective amendment on the stability of photometric performance during the heat test, with particular reference to the movement of the cut-off line, clarifies the test cycle and also aligns the requirements of Regulations Nos. 19, 98, 112, 113 and 123. In addition to resolving problems of interpretation presented by the current text, this collective amendment will assist the Informal Working Group “Simplification of Lighting and Light-Signalling Regulations” in drafting the new simplified Regulations which is underway.

This proposal removes the requirement to indicate the rated wattage in the marking of lamps equipped with electronic light source control gear and/or non-replaceable light sources and/or light source module(s). From an electronic point of view, the information of the wattage brings no benefit and is confusing if the same module is used in different systems and at different wattages.

Supplement 3 to the 01 series of amendments to UN R 98, 112, and 123 deleted the measurement point HV from the photometric requirement table. The HV measurement point, however, remains a requirement for checking photometric stability. This proposal removes the HV measurement point from the photometric stability requirements for the passing beam. The HV measurement point remains a valid for the driving beam.

During its 69th session, GRE adopted proposals to update the Conformity of Production (CoP) procedures for lighting and light-signalling devices, but decided to await the work of a GTB task force on the simplification of CoP provisions for AFS before addressing UN R123. This proposal amends the CoP procedures in line with those agreed for UN R112 (document GRE/2013/37) to create simplified photometric CoP tables for each class (C, V, W, E, R, RADB) with its applicable 0/20/30 per cent limits. Furthermore, the task force clarified which tests are necessary for CoP testing and which are necessary only for type approval testing. The methods and requirements for the “initial” type approval remained unchanged. An overview of the main AFS characteristics can be found in documents GRE-48-28 and GRE-48-30.

The current requirements on light source failure in lamps equipped with multiple light sources differ across UN Regulations. GTB submitted and then withdrew a proposal to align these requirements (GRE/2016/13). This updated proposal improves upon the text of the previous proposal to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required.

This collective amendment extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123 (as presented in the previous session document GRE-75-14). The proposal would allow for the use of regulated replaceable LED light sources according to Regulation No. 128 in all applications where the use of LED modules is already permitted.

The DETA informal group has developed a Unique Identifier for simplified type-approval markings. This document aims to apply the Unique Identifier to the new draft regulation on light-signalling devices.

Correction to the proposal for a collective amendment to Regulations Nos. 7, 23, 38, 48, 77, 91 and 119. Since the cornering lamp projects a beam to the left and right of the reference axis, it is not relevant to check the photometric values in the reference axis (HV). Therefore, the test point at 2.5°D, 45°L or R shall be used.

Proposal to update document GRE/2016/34. At the 73rd GRE session, France proposed to delete a design restrictive requirement (GRE/2015/22 and GRE-73-26). This proposal received comments from Germany and the Netherlands. Poland suggested a different approach on this issue (GRE-73-21). The Chair invited France, Germany, Netherlands, Poland, CLEPA and IEC to prepare a revised proposal for the next session. Based upon the approach proposed in GRE/2015/22 and GRE-73-26, GTB has investigated the specification of minimum levels of flux projected in critical zones of the passing beam distribution. This approach offers a technology-neutral performance based requirement. The result of the GTB study is to propose minimum projected flux requirements in two zones:
a) 15°D-1°U/30°L-30°R to ensure overall adequate illumination of the road and
b) 3.5°D-1°U/30°L-30°R to ensure sufficient range.

The collective amendment presented in GRE/2016/34 extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123. The introduction of LED light source categories under UN R128 for forward lighting applications (front fog, low beam, high beam,
AFS) is planned for 2017. This presentation explains the plans, timeline, and dependencies GTB proposes to address through the collective amendment, especially within the context of the simplification of lighting regulations program.

Editorial improvements to the proposal for Supplement 8 to the 01 series of amendments to UN R123.

Revised proposal (removing the section on UN R48 and incorporating corrections noted in document GRE-76-07) to refine the requirements for lamps equipped with several light sources, including in systems fitted with an operating tell-tale that indicates the failure of any one of these light sources. In the case of failure of any one light source in a single lamp containing more than one light source, either the light intensity must comply with the minimum intensity required in the table of standard light distribution in space or, for lamps used in systems where a tell-tale indicates the failure of any one of the light sources, the light intensity in the axis of reference must be at least 50 per cent of the minimum intensity required. This collective amendment addresses Regulations Nos. 7, 23, 38, 77, 91 and 119. The proposals concerning UN R48 will be resubmitted for consideration during the 77th GRE session.

GTB proposal for incorporation of the DETA Universal Identifier approval mark into the UN Regulation on direction indicators.