Updated status of deliberations on aligning certain UN Regulations with the requirements of the proposed international whole vehicle type approval system.

Summary of items from the 11th meeting of the working group on revising the 1958 Agreement, especially with regard to the introduction of the International Whole Vehicle Type Approval System, use of the Data Exchange for Type-Approval information, and changes aimed at improving accessibility to the agreement worldwide.

Final version (under the “Phase 1” program of revisions) of the text prepared by the Informal Group on “Agricultural Vehicles Lighting Installation” (AVLI) for submission to the GRE in order to update and revise Regulation No. 86.

Proposal to amend UN R3 in order to address the recent introduction of devices with a reduced light distribution to be mounted no higher than 750 mm. 1. The proposal would also require colorimetric and photometric testing to type approve each variation in color of an approved device.

Proposal to delete unnecessary markings for LED front fog lamps that have non-replaceable LED modules and to correct and clarify the requirements for colour measurement and ultraviolet (UV) testing of light emitting diode (LED) modules.

Proposal to amend the test procedure for reversing lamps and maneuvering lamps equipped with light sources other than filament lamps. Currently, the lamps are required to meet photometric parameters after one minute and 30 minutes of operation. Under normal use, these lamps are operated for no more than six minutes at a time. This proposal would set the second measurement point at 10 minutes rather than 30 minutes. This change would also align the procedure with SAE standard J1889.1.

Proposal to introduce new halogen categories H18, H19 and H20 and some minor corrections to existing categories.

Proposal to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Front fog lamps may be reciprocally incorporated with the main beam and in some cases, it is required to switch off the front fog lamp when the main beam is operated to avoid overheating of the device. In this case, Regulation No. 19 requires a “/” in the approval marking. However, the current text in paragraph 6.3.7 of Regulation No. 48 requires that “it shall be possible to switch the front fog lamps ON and OFF independently of the main-beam headlamps”. This proposal is intended to remove the conflict between the texts of the two regulations.

Revised proposal (superseding document GRE/2014/7) to introduce the possibility of interdependent lamps for dedicated motorcycle lamps. The proposal reflects recent amendments to Regulations Nos. 6 and 7 and meets the visibility angle requirements of Regulations Nos. 50 and 53. The concern is that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features.

Revised proposal (superseding document GRE/2014/8) to allow for the installation of interdependent lamps for L3 category vehicles. The amendment also reflects recent amendments to Regulation No. 48, Supplement 2 to its 06 series of amendments and further includes some editorial corrections of current Regulation No. 53 texts. The concern is that the rear trunk lid commonly used for four-wheeled vehicles may be adapted for future scooter type motorcycles to secure the storage space for helmet, etc. Current lamp requirements impose design constraints that may hamper the proper development of such storage features.

Consolidated proposal prepared by AVLI informal working group to update and revise Regulation No. 86.

Proposal to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Proposal to introduce a new category: D8R.

Proposal to simplify measuring the objective luminous flux of light emitting diode (LED) module(s) and to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Proposal for revised guidelines and procedures for UN Regulations pursuant to the development of the International Whole Vehicle Type Approval system, including a procedure for exemptions of new technologies from current UN Regulation requirements and the procedure for updating the IWVTA regulation (proposed UN R0).

Version including a revised paragraph 12 transmitted by the Russian Federation and OICA.

Proposal to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity. The proposal would also simplify the measurement of the objective luminous flux of light emitting diode (LED) module(s) and correct the ultraviolet (UV) table in the regulation.