Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definition of “type”, with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings.

Although documents GRE/2013/45 and GRE-70-02 were adopted by GRE at its last (70th) session, this proposal consolidates the amendments and offers editorial improvements to the provisions concerning markings in Regulations Nos. 19, 23, 38, 65 and 119. These editorial improvements aim to clarify that the devices, and not only the samples, shall bear the trade name or mark and align the requirements with the other correctly worded regulations to avoid misunderstanding.

The text reproduced below was prepared by the expert from the International Automotive Lighting and Light Signalling Expert Group (GTB) to amend the requirements to clarify the “n-1 rule” provisions in relation to an interdependent lamp system. This document has been withdrawn from consideration.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to amend the requirements relating to failure indication by removing the differentiation between filament and LED light sources. (Currently the provisions in UN Regulation No. 6 treat the failure of a lamp equipped with filament light sources differently to one equipped with LED. Similar requirements in UN Regulation No. 7 do not include this differentiation.)

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definitions and requirements associated with the installation of “single lamps”, “lamps marked D” and “Interdependent lamps”.

GTB white paper on priorities and objectives for the simplification of lighting regulations, especially regarding reduction of the current burdens associated with the necessity of collective amendments in the development of these regulations and the longer-term difficulties to be overcome in restructuring these regulations and their legal framework.

Status report on efforts to resolve concerns related to automatic headlamp leveling provisions and their impact on visibility and on-coming driver glare.

GTB discussion paper to focus attention on defining the problem(s) to be resolved through a the simplification of UN lighting regulations.

Brief presentation raising question over the necessity to have triangular reflectors on the rear of large trailers and seeking greater flexibility in such rear reflectors.

Proposal to introduce new halogen categories H18, H19 and H20 and some minor corrections to existing categories.

Proposal to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Front fog lamps may be reciprocally incorporated with the main beam and in some cases, it is required to switch off the front fog lamp when the main beam is operated to avoid overheating of the device. In this case, Regulation No. 19 requires a “/” in the approval marking. However, the current text in paragraph 6.3.7 of Regulation No. 48 requires that “it shall be possible to switch the front fog lamps ON and OFF independently of the main-beam headlamps”. This proposal is intended to remove the conflict between the texts of the two regulations.

Proposal to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Proposal to introduce a new category: D8R.

Proposal to simplify measuring the objective luminous flux of light emitting diode (LED) module(s) and to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Proposal to amend the test procedure for reversing lamps and maneuvering lamps equipped with light sources other than filament lamps. Currently, the lamps are required to meet photometric parameters after one minute and 30 minutes of operation. Under normal use, these lamps are operated for no more than six minutes at a time. This proposal would set the second measurement point at 10 minutes rather than 30 minutes. This change would also align the procedure with SAE standard J1889.1.

Proposal to delete unnecessary markings for LED front fog lamps that have non-replaceable LED modules and to correct and clarify the requirements for colour measurement and ultraviolet (UV) testing of light emitting diode (LED) modules.

Proposal to amend UN R3 in order to address the recent introduction of devices with a reduced light distribution to be mounted no higher than 750 mm. 1. The proposal would also require colorimetric and photometric testing to type approve each variation in color of an approved device.

Proposal to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity. The proposal would also simplify the measurement of the objective luminous flux of light emitting diode (LED) module(s) and correct the ultraviolet (UV) table in the regulation.

Proposal to introduce new categories LR3A, LR3B, LR4A, LR4B and correct one value in the ultraviolet (UV) table.

According to Regulation No. 119, cornering lamps that are equipped with light sources other than filament lamps, are required to meet the relevant photometric requirements after one minute and after 30 minutes of operation. However, under normal traffic conditions, these lamps are operated for no more than 6 minutes. This proposal would therefore would require the second test after 10 minutes instead of the current 30 minutes, in accordance with standard SAE J1889.

Proposal to simplify measuring the objective luminous flux of light emitting diode (LED) module(s), correct the ultraviolet (UV) table, and to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

GTB analysis of “collective amendments” to lighting regulations received by the Working Party on Lighting and Light-signalling Equipment (GRE) where a single change impacts multiple lighting regulations resulting in the proliferation of amendment proposals.

During the 71st session of GRE, the experts from GTB presented the outcome of a study on visibility and glare of automotive low beam headlamps; see informal document GRE-71-32. The study concentrated on levelling in relation to load. The major objectives of the study were to improve the understanding of different factors that influence visibility and glare and to identify results of the study that might reveal alternatives for automatic static levelling. The deciding factors in headlamp glare have been determined to be the vehicle pitch angle, loading conditions and initial headlamp aim. Therefore, this proposal looks at replacing the light source technology and the light source 2,000 lm criterion in UN Regulation No. 48 as criteria for the requirement for automatic levelling with performance requirements based upon these deciding factors.

This proposal would correct an error introduced into the regulation through Supplement 16.

Front fog lamps may be reciprocally incorporated with the main beam and in some cases, it is required to switch off the front fog lamp when the main beam is operated to avoid overheating of the device. In this case, Regulation No. 19 requires a “/” in the approval marking. However, the current text in paragraph 6.3.7 of Regulation No. 48 requires that “it shall be possible to switch the front fog lamps ON and OFF independently of the main-beam headlamps”. This proposal is intended to remove the conflict between the texts of the two regulations. This proposal supersedes and replaces document GRE/2014/22 and has been prepared to remove ambiguities identified in the previous proposal.

Proposal to correct an error introduced by Supplement 21 to the 02 series of Regulation No. 7 (document WP29/2012/65). Supplement 21 introduced provisions for the use of light-emitting diode (LED) light sources and corrected the provisions concerning approval markings.