Proposal form the Ad Hoc Group on Child Restraint Systems to introduce definitions, requirements and a test procedure for lower tether anchorages.

Proposal to introduce definitions, requirements and a test procedure for lower tether anchorages.

Proposal to introduce definitions, requirements and a test procedure for lower tether anchorages.

Proposal to clarify the single belt route principle mentioned in paragraph 3.2.2.

Proposal to introduce provisions for labelling/identifying buses and trucks equipped with an electric drivetrain in a manner consistent with similar provisions already provided for vehicles fueled by Liquified Petroleum Gas (LPG), Compressed Natural Gas (CNG), Liquid Natural Gas (LNG) and Compressed Hydrogen (H2).

Proposal to align the text with the guidelines on UN regulatory procedures and transitional provisions in UN Regulations (document ECE/TRANS/WP.29/1044/Rev.3). Under the guidelines, a UN Regulation (in this case, UN R157) making reference to the provisions of another UN Regulation (in this case, UN R10) shall not require actual approval to that UN regulation but simply refer to the provisions of that UN Regulation.

Proposal to consider exploring possibilities for ensuring reliable and robust mileage values as generated by and stored in vehicles (and/or elsewhere).

The proposal aimed to an identification of buses and trucks equipped with an electric drivetrain which is consistent with existing regulated identification for Liquified Petroleum Gas (LPG), Compressed Natural Gas (CNG), Liquid Natural Gas (LNG) and Compressed Hydrogen (H2) fuelled trucks and buses.

The proposed amendment does not intend to change the requirements nor the level of stringency. The footnote to paragraph 3.2.2. is added to further clarify the definition of the use of a one belt route. In its current state, the text apparently has been interpreted as to allow the use of a single belt route for each application that an Enhanced Child Restraint System (ECRS) would offer. That way, one belt route for a rearward facing ECRS (integral) and a second belt route for a forward facing (non- integral) ECRS has been introduced, making a combination of C and E.

The text reproduced prepared by the Ad Hoc Group on Child Restraint Systems to introduce definitions, requirements and a test procedure for lower tether anchorages.

The text prepared by the Ad Hoc Group on CRS, aiming to introduce definitions, requirements and a test procedure for lower tether anchorages.

The text prepared by the Ad Hoc Group on Child Restraint Systems, aiming to introduce definitions, requirements and a test procedure for lower tether anchorages.

Proposal to clarify the application of UN R10 on electromagnetic compatibility requirements to ALKS.

This document summarises the reviews conducted by the GR working parties on the fitness for ADS of UN Regulations and GTR for application to ADS vehicles. This document represents the current opinions of the experts at the time of submission, and the recommendations contained inside may evolve significantly during the next steps of the process of reviewing and amending Regulations.

Proposal to clarify the need to have a support device for centre axle trailers, independent of the type of coupling device.

Small group (France, Netherlands, ETRTO, BIPAVER) proposal to restructure retreaded tyre requirements and regulations.

Small group proposal to split retreaded tyre requirements into a new UN Regulation.

Proposal from a small group effort for uniform provisions concerning the approval of pre-cured tread materials which are used for producing retreaded tyres or the approval of retreaded tyres produced by using mould cure process with regard to their snow performance.

Proposal to introduce provisions for the specifications and calibration procedure of the 3-D “H”-point machine and the procedure for determining the “H”-point and the actual torso angle for seating positions in motor vehicles, to be used in all referenced UN Regulations and GTR.

Proposal to introduce provisions for identification of buses and trucks equipped with an electric drivetrain consistent with existing regulated identification for Liquified Petroleum Gas (LPG), Compressed Natural Gas (CNG), Liquid Natural Gas (LNG) and Compressed Hydrogen (H2) fueled trucks and buses.

Proposal to clarify the need to apply, when relevant, the Type IIA test in Annex 15 for alternative brake lining purposes (e.g., in the case of vehicles with regenerative braking for Type IIA endurance test purposes to use the friction brake as an alternative to the regular endurance brake).

Proposal to delineate the scope of UN R79 vis-à-vis the draft new UN Regulation on Driver Control Assistance Systems (DCAS).

Information document to inform GRSG of the proposal to introduce provisions for the specifications and calibration procedure of the 3-D “H”-point machine and the procedure for determining the “H”-point and the actual torso angle for seating positions in motor vehicles, to be used in all referenced UN Regulations and GTR. The proposal will be formally considered by GRSP in December 2023.

Copy of document GRVA-17-49.

Proposal to require a support device for centre axle trailers, independent of the type of coupling device.

Document GRVA-17-49 from the September 2023 GRVA session.

Proposal to differentiate between the scope of UN R79 and the proposed UN Regulation on Driver Control Assistance Systems (DCAS).

Explanations and clarifications concerning the “one belt route” provisions.

Proposal to define the judgement phase of the dynamic seat belt component test on the sled as limited up to the point where the manikin contacts the seat back during its backward movement after impact.

Proposal to introduce provisions for the specifications and calibration procedure of the 3-D “H”-point machine and the procedure for determining the “H”-point and the actual torso angle for seating positions in motor vehicles for use across all relevant UN Regulations and GTR.

Proposal to enable identification of buses and trucks equipped with an electric drivetrain.

Request for authorization to develop amendments to remove references to the three-Dimensional “H”-point machine and to move its drawings and specifications to Mutual Resolution No. 1.