Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. This document supersedes document WP.29/2013/18.

Clarification of the proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to improve the clarifications proposed regarding the requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to amend document GRE/2013/18 (on aligning UN R48 with UN R112) and establishing limits for minimum and maximum voltages values.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Proposal to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic leveling. This document supersedes document GRE/2013/15.

Proposal to amend UN R48 in order to enable type-approval of direction indicators with variable apparent surfaces.

Proposal to introduce the following into Regulation No. 48:
a) General definition of ‘tell-tale’, as also currently defined in Regulation No. 121;
b) Requirement that the specifications of the tell-tale (location, identification, symbol, illumination and colour) shall meet the relevant requirements of Regulation No. 121;
c) Provision that tell-tales shall always provide an optical signal, thus aligning with Regulation No. 121; however, it is suggested to allow additional signals (auditory or any equivalent signal);
d) New definition of a ‘failure tell-tale’ and stating the mandatory presence of such tell-tale for the daytime running lamp in certain cases;
e) Editorial changes clarifying the situation for a few other cases in Regulation No. 48, where apparently also a ‘failure tell-tale’ was meant.

Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. This document supersedes document WP.29/2013/18.

Clarification of the proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to improve the clarifications proposed regarding the requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to amend document GRE/2013/18 (on aligning UN R48 with UN R112) and establishing limits for minimum and maximum voltages values.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Proposal to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic leveling. This document supersedes document GRE/2013/15.

Proposal to amend UN R48 in order to enable type-approval of direction indicators with variable apparent surfaces.

Proposal to introduce the following into Regulation No. 48:
a) General definition of ‘tell-tale’, as also currently defined in Regulation No. 121;
b) Requirement that the specifications of the tell-tale (location, identification, symbol, illumination and colour) shall meet the relevant requirements of Regulation No. 121;
c) Provision that tell-tales shall always provide an optical signal, thus aligning with Regulation No. 121; however, it is suggested to allow additional signals (auditory or any equivalent signal);
d) New definition of a ‘failure tell-tale’ and stating the mandatory presence of such tell-tale for the daytime running lamp in certain cases;
e) Editorial changes clarifying the situation for a few other cases in Regulation No. 48, where apparently also a ‘failure tell-tale’ was meant.

Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. This document supersedes document WP.29/2013/18.

Clarification of the proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to improve the clarifications proposed regarding the requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to amend document GRE/2013/18 (on aligning UN R48 with UN R112) and establishing limits for minimum and maximum voltages values.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Proposal to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic leveling. This document supersedes document GRE/2013/15.

Proposal to amend UN R48 in order to enable type-approval of direction indicators with variable apparent surfaces.

Proposal to introduce the following into Regulation No. 48:
a) General definition of ‘tell-tale’, as also currently defined in Regulation No. 121;
b) Requirement that the specifications of the tell-tale (location, identification, symbol, illumination and colour) shall meet the relevant requirements of Regulation No. 121;
c) Provision that tell-tales shall always provide an optical signal, thus aligning with Regulation No. 121; however, it is suggested to allow additional signals (auditory or any equivalent signal);
d) New definition of a ‘failure tell-tale’ and stating the mandatory presence of such tell-tale for the daytime running lamp in certain cases;
e) Editorial changes clarifying the situation for a few other cases in Regulation No. 48, where apparently also a ‘failure tell-tale’ was meant.

Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. This document supersedes document WP.29/2013/18.

Clarification of the proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to improve the clarifications proposed regarding the requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to amend document GRE/2013/18 (on aligning UN R48 with UN R112) and establishing limits for minimum and maximum voltages values.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Proposal to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic leveling. This document supersedes document GRE/2013/15.

Proposal to amend UN R48 in order to enable type-approval of direction indicators with variable apparent surfaces.

Proposal to introduce the following into Regulation No. 48:
a) General definition of ‘tell-tale’, as also currently defined in Regulation No. 121;
b) Requirement that the specifications of the tell-tale (location, identification, symbol, illumination and colour) shall meet the relevant requirements of Regulation No. 121;
c) Provision that tell-tales shall always provide an optical signal, thus aligning with Regulation No. 121; however, it is suggested to allow additional signals (auditory or any equivalent signal);
d) New definition of a ‘failure tell-tale’ and stating the mandatory presence of such tell-tale for the daytime running lamp in certain cases;
e) Editorial changes clarifying the situation for a few other cases in Regulation No. 48, where apparently also a ‘failure tell-tale’ was meant.

Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. This document supersedes document WP.29/2013/18.

Clarification of the proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to improve the clarifications proposed regarding the requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to amend document GRE/2013/18 (on aligning UN R48 with UN R112) and establishing limits for minimum and maximum voltages values.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Proposal to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic leveling. This document supersedes document GRE/2013/15.

Proposal to amend UN R48 in order to enable type-approval of direction indicators with variable apparent surfaces.

Proposal to introduce the following into Regulation No. 48:
a) General definition of ‘tell-tale’, as also currently defined in Regulation No. 121;
b) Requirement that the specifications of the tell-tale (location, identification, symbol, illumination and colour) shall meet the relevant requirements of Regulation No. 121;
c) Provision that tell-tales shall always provide an optical signal, thus aligning with Regulation No. 121; however, it is suggested to allow additional signals (auditory or any equivalent signal);
d) New definition of a ‘failure tell-tale’ and stating the mandatory presence of such tell-tale for the daytime running lamp in certain cases;
e) Editorial changes clarifying the situation for a few other cases in Regulation No. 48, where apparently also a ‘failure tell-tale’ was meant.

Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. This document supersedes document WP.29/2013/18.

Clarification of the proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to improve the clarifications proposed regarding the requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to amend document GRE/2013/18 (on aligning UN R48 with UN R112) and establishing limits for minimum and maximum voltages values.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Proposal to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic leveling. This document supersedes document GRE/2013/15.

Proposal to amend UN R48 in order to enable type-approval of direction indicators with variable apparent surfaces.

Proposal to introduce the following into Regulation No. 48:
a) General definition of ‘tell-tale’, as also currently defined in Regulation No. 121;
b) Requirement that the specifications of the tell-tale (location, identification, symbol, illumination and colour) shall meet the relevant requirements of Regulation No. 121;
c) Provision that tell-tales shall always provide an optical signal, thus aligning with Regulation No. 121; however, it is suggested to allow additional signals (auditory or any equivalent signal);
d) New definition of a ‘failure tell-tale’ and stating the mandatory presence of such tell-tale for the daytime running lamp in certain cases;
e) Editorial changes clarifying the situation for a few other cases in Regulation No. 48, where apparently also a ‘failure tell-tale’ was meant.

Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. This document supersedes document WP.29/2013/18.

Clarification of the proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to improve the clarifications proposed regarding the requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to amend document GRE/2013/18 (on aligning UN R48 with UN R112) and establishing limits for minimum and maximum voltages values.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Proposal to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic leveling. This document supersedes document GRE/2013/15.

Proposal to amend UN R48 in order to enable type-approval of direction indicators with variable apparent surfaces.

Proposal to introduce the following into Regulation No. 48:
a) General definition of ‘tell-tale’, as also currently defined in Regulation No. 121;
b) Requirement that the specifications of the tell-tale (location, identification, symbol, illumination and colour) shall meet the relevant requirements of Regulation No. 121;
c) Provision that tell-tales shall always provide an optical signal, thus aligning with Regulation No. 121; however, it is suggested to allow additional signals (auditory or any equivalent signal);
d) New definition of a ‘failure tell-tale’ and stating the mandatory presence of such tell-tale for the daytime running lamp in certain cases;
e) Editorial changes clarifying the situation for a few other cases in Regulation No. 48, where apparently also a ‘failure tell-tale’ was meant.

Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. This document supersedes document WP.29/2013/18.

Clarification of the proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to improve the clarifications proposed regarding the requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to amend document GRE/2013/18 (on aligning UN R48 with UN R112) and establishing limits for minimum and maximum voltages values.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Proposal to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic leveling. This document supersedes document GRE/2013/15.

Proposal to amend UN R48 in order to enable type-approval of direction indicators with variable apparent surfaces.

Proposal to introduce the following into Regulation No. 48:
a) General definition of ‘tell-tale’, as also currently defined in Regulation No. 121;
b) Requirement that the specifications of the tell-tale (location, identification, symbol, illumination and colour) shall meet the relevant requirements of Regulation No. 121;
c) Provision that tell-tales shall always provide an optical signal, thus aligning with Regulation No. 121; however, it is suggested to allow additional signals (auditory or any equivalent signal);
d) New definition of a ‘failure tell-tale’ and stating the mandatory presence of such tell-tale for the daytime running lamp in certain cases;
e) Editorial changes clarifying the situation for a few other cases in Regulation No. 48, where apparently also a ‘failure tell-tale’ was meant.

Text prepared by Germany with support from The Netherlands, to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize this with operating voltage requirements in UN Regulation 48.

Proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48. This document supersedes document WP.29/2013/18.

Clarification of the proposal to introduce requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to improve the clarifications proposed regarding the requirements to avoid intentional non-approved (voltage) variation of the principal passing beam, using halogen light sources and to harmonize them with the operating voltage requirements in UN Regulation No. 48

Proposal to amend document GRE/2013/18 (on aligning UN R48 with UN R112) and establishing limits for minimum and maximum voltages values.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Proposal to introduce an alternative set of performance-based requirements for the initial aiming of dipped-beam headlamps and allowing removing the artificial 2,000 lm borderline and Light Emitting Diode (LED) automatic leveling. This document supersedes document GRE/2013/15.

Proposal to amend UN R48 in order to enable type-approval of direction indicators with variable apparent surfaces.

Proposal to introduce the following into Regulation No. 48:
a) General definition of ‘tell-tale’, as also currently defined in Regulation No. 121;
b) Requirement that the specifications of the tell-tale (location, identification, symbol, illumination and colour) shall meet the relevant requirements of Regulation No. 121;
c) Provision that tell-tales shall always provide an optical signal, thus aligning with Regulation No. 121; however, it is suggested to allow additional signals (auditory or any equivalent signal);
d) New definition of a ‘failure tell-tale’ and stating the mandatory presence of such tell-tale for the daytime running lamp in certain cases;
e) Editorial changes clarifying the situation for a few other cases in Regulation No. 48, where apparently also a ‘failure tell-tale’ was meant.