Introduction to the blind spot detection test procedure developed by TRL.

Highway Loss Data Institute report, provided by Transport for London, regarding accident data related to collision-avoidance system, including “LaneWatch” passenger-side blind spot detection system.

Proposal from the IWVTA informal group to extract provisions from UN R116 into a new UN Regulation concerning the approval of immobilizers and the approval of a vehicle with regard to its immobilizer.

Rationale for the proposal to harmonize UN R110 with ISO 11439:2013.

Comments from NGV Global on the proposals from Italy (GRSG-112-28) and Germany (GRSG-112-33) regarding the testing and inspection of CNG cylinders.

Proposal to insert new provisions on the location on the vehicle of the filling unit, marking of the LPG container date of production, and a limitation on the maximum service life of LPG containers to 15 years.

Proposal from the IWVTA informal group to limit the scope of UN R116 to the protection of motor vehicles against unauthorized use and the approval of devices to prevent unauthorized use (while establishing new regulations to incorporate the provisions concerning alarm systems and immobilizers)

Proposal from the IWVTA informal group to extract provisions from UN R116 into a new UN Regulation concerning the approval of immobilizers and the approval of a vehicle with regard to its immobilizer.

Proposal from the IWVTA informal group to extract provisions from UN R116 into a new UN Regulation concerning the approval of vehicle alarm systems and the approval of a vehicle with regard to its vehicle alarm system.

Proposal for new safety provisions with regard to LPG systems having hydraulic interconnections with the petrol or diesel fueling system through which inter-flows of fuels may occur.

Proposal to establish procedures for the approval of non-seamless gas tube(s), gas tube(s) made of materials other than copper, stainless steel, and steel with corrosion-resistant coating, and their couplings in Liquefied Petroleum Gas (LPG) vehicles provided they can withstand the applicable tests according to Annex 15.

Proposal presented as an alternative to the previous proposal from Poland (GRSG/2017/10) to require manufacturers to mark the approval extension number on any accessories relevant to the bonfire test (multivalve or, when approved separately, pressure relief valve (discharge valve) and pressure relief device) so that the fitting of any accessory not on the list of approved configurations (Table 3 in the appendix of Annex 2B) will be prevented/forbidden. This solution would imply a new requirement in Annex 2A for the marking of the accessories fitted to the containers.

Proposal to require, in instances where ogive protective covers are fitted to a cylinder, that the covers be removed before conducting the impact damage (drop) test.

Proposal to harmonize the requirements on Compressed Natural Gas (CNG) and/or Liquefied Natural Gas (LNG) vehicles of UN Regulation No. 110 with those of the international standard ISO 11439:2013.

Proposal to clarify the test requirements in alignment with the French text of the regulation by amending paragraph 5.10 to read “There shall be no protruding parts, sharp edges, etc. near the installed tank likely to increase the risk of damage on the tank in the event a collision to the front, the side or the rear of the vehicle.” (Modified text in bold)

Proposal to add a telltale and symbols for “Accident Emergency Call System (AECS)” and to align UN R121 with the 07 series of amendments to UN Regulation No. 16:

1. the term “seat belt” is replaced by “safety belt”,
2. the symbol for safety belt, defined in item 21 of Table 1 in the Regulation, may be displayed in different colours to convey different meanings. Therefore, the existing footnote 18 has been added to item 21, and
3. this symbol may be replaced by different symbols for seats other than those of the front row. Therefore, a new footnote 22 is added to item 21.

Proposal for editorial corrections to align the definition on plastic glazing between the original English version and the French translation as well as of the communication annex on principal/secondary characteristics for laminated-glass windscreens.

Proposal to correct the scope of the GTR to align with Part A of the GTR, UN R43, and regional/national interpretations and to align the impact test procedure description with that of UN R43 and ISO 3537. The scope is amended to add “panes or as partitioning” while deleting the wording “use of double windows panes, each pane is considered a separate item of glazing panes”. The impact test procedure is clarified to define the point of impact with reference to the test piece (not the current “supported area”) and within 25 mm of its geometric centre and 50 mm of its centre.

Proposal to align the headform test with the deceleration measurement and the test of resistance to abrasion with ISO 15082:2016-11, including changes to the test details, correction of the headform calibration values, and the introduction of abrasion reference materials. The latter is combined with an abrasive-wheel qualification and a correction calculation (for plastic materials only).

The proposal also amends Figure 2a of Annex 21 to better reflect the meaning of paragraph 2.4.2.2. of Annex 21, mainly to clarify the lateral limits of any opaque obscuration in this area.

Proposal for editorial corrections to align the definition on plastic glazing between the original English version and the French translation as well as of the communication annex on principal/secondary characteristics for laminated-glass windscreens.

Proposal to correct the definition of “manual valve”, including deletion of the phrase “rigidly fixed to the cylinder or tank”. The definition of the manual valve as part of the accessories fitted to the container or tank (para. 4.16.) is different from the definition specified in paragraph 4.22. The proposed editorial change aims at clarifying the text of these definitions.