Input from the WP.29 secretariat for the text explaining the meaning of a “revision” to a UN Regulation and of a “version” of a UN Regulation.

Document GRE/2016/10 proposed to refine the transitional provisions of UN R48 pursuant to possibilities for the application of the regulation within the International Whole Vehicle Type Approval system. Since IWVTA allows for approvals to earlier versions of current regulations, the possibility exists where optional installation of advanced equipment could entail mandatory compliance with the latest version of UN R48. However, UN R48 imposes broad requirements such that efforts to add certain safety equipment are hindered by concerns over compliance with a broad range of requirements under the latest version of UN R48 that raises the consumer price to prohibitive levels. Therefore, OICA supports the solution proposed by GTB (document GRE/2016/10).

Working draft prepared for consideration during the 20th subgroup session.

Revised question no. 13 pursuant to the subgroup discussions.

Proposal to

• amend the tyre dimensional requirements,
• amend the requirements for the load/speed performance test,
• align definitions and content with the other tyre regulations (UN Regulations Nos. 117, 54, 75 etc.),
• include a definition of “manufacturer” extracted from the resolution R.E.3,
• adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links, and
• add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Proposal to:

• correct the code 19 rim diameter, amend the tyre dimension requirements,
• modify the marking requirements to replace PSI with kilopascals (“kPa”),
• change the measurement units for drum speed from min-1 to km.h-1 and align the wording in Annex 7, Appendix 1 with the text of the Regulation,
• add new tyre sizes to Annex 5, allow for special tyres that can also be used as snow tyres to be marked with the inscription M+S, M.S, or M&S while remaining in the category of use “special”,
• align definitions and content with the other tyre regulations (UN Regulations Nos. 30, 117, 75 etc.),
• include a definition of “manufacturer” extracted from the resolution “R.E.3”
• adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links, and
• add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Proposal to remove tyre pressure monitoring systems from UN R64 pursuant to establishing a stand-alone regulation and to facilitate the development of the regulation on international whole vehicle type approvals.

Proposal to amend the tyre dimension requirements.

Proposal to align UN R106 with international standards (ETRTO, T&RA and ISO 4351-2 table 2) with regard to Improved Flexion (IF) tyres and Very high Flexion (VF) tyres to add load indexes to the table in the Annex 4 to keep up with the technical evolution of tyres. This proposal also clarifies the application of EC Regulation 167/2013 which refers to UN R106.

Proposal to:
a) Align definitions and content with the other tyre regulations (UN Regulations Nos. 30, 54, 75 etc.);
b) Include a definition of “manufacturer” extracted from the resolution “R.E.3”;
c) Adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links; and
d) Add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Proposal for a new UN Regulation on tire installation for use within the International Whole Vehicle Type Approval system.

Proposal for a new UN Regulation based upon brake-assist system provisions extracted from UN R13-H in order to facilitate work on the international whole vehicle type approval system.

Proposal for a new UN Regulation comprised of provisions concerning electronic stability control systems extracted from UN R13-H in order to facilitate work on the international whole vehicle type approval system.

Proposal for the explanatory report detailing the decisions and rationale involved in the development of Amendment 1 to the GTR on passenger and light truck/commercial vehicle tires.

Presentation of a proposal for type approval authority “attestations” to address cases where a UN Regulation contains provisions not required in all markets. For example, UN R48 contains provisions for daytime running lamps presently required in the EU but not in Japan. An attestation would declare a vehicle compliant with all aspects of UN R48 except that the vehicle is not fitted with DRL.

Proposal of Amendment 1 to UN GTR No. 16 to include new provisions on wet grip performance, rolling resistance, and qualification of tires for use in severe snow conditions for passenger cars and light trucks/commercial vehicles. The amendment also reflects recent changes adopted in US Federal Motor Vehicle Safety Standards (tire strength and tubeless tire bead unseating resistance) and UN Regulations Nos. 30 and 54.

Proposal from the informal working group on the International Whole Vehicle Type Approval to restructure UN R116 into two separate regulations. The regulation addresses anti-theft, alarm, and immobilizer aspects of theft prevention. Since these aspects may be mandatory or optional depending upon the country or market, the application of UN R116 to whole vehicle type approval becomes problematic. This proposal would extract the immobilizer provisions into a separate new regulation.