Document prepared by the WP.29 secretariat to provide a consolidated updated version of the proposed Revision 3 to the 1958 Agreement. The secretariat anticipates a decision by the World Forum to seek unanimous agreement on this proposed final text during its March 2016 session.

In response to concerns that approval agencies may not grant manufacturers the additional 1dB for L(wot) on conformity of production tests as changes had been made to Annex 6 of R41-04, GRB issued an interpretation recorded in the report of its 56th session. The proposal formalizes the interpretation as an explicit provision of the regulation.

Proposal to clarify the wording of the 03 series of amendments to UN R51 as adopted by the World Forum in June 2015 (document WP.29/2015/62). The adopted wording could lead to the interpretation that sound levels measured on the left side of the vehicle are to be averaged with levels measured on the right side of the vehicle. The proposed new wording clarifies that the overall sound emission is assessed individually per vehicle side.

Proposal as prepared by the UN R55 informal group and approved by the GRRF to update UN R55 with respect to:
a) Requirements on remote indication;
b) Availability of information on coupling fixing points for A50X couplings;
c) On lateral strength of drawbars; and
d) a new class definition for fully automatic drawbar couplings.

Proposal to insert a new Introduction section to the regulation in order to highlight technical issues related to the installation of LDWS on some specific vehicles included in the scope of the regulation.

Proposal to amend the Introduction of the regulation to highlight technical issues related to the installation of AEBS on some specific vehicles included in the scope of the regulation.

Proposal to correct an oversight by aligning the “alternative procedures” provisions of the regulation with the previously adopted amendment of the regulation that raised the rear-impact speed to between 48 and 52 km/h (03 series of amendments).

Proposal to clarify that fully integrated surveillance mirrors may be mounted below 2 metres in cases where they are integrated in a housing including one or more Class II or III mirrors.

Proposal to

• extend requirements for exterior rear-view mirrors to camera monitor systems;
• reduce the speed threshold for deactivation of emergency controls from 5 km/h to 3 km/h;
• clarify the requirements concerning the height of steps in vehicles which comply with Annex 8;
• limit the mandatory application of the requirements for dedicated areas for prams and pushchairs to Class I vehicles;
• require activation of the alarm and fire suppression systems as soon as the heater is in function regardless of whether the engine is operating;
• extend requirements for exposed seats adjacent to step wells to apply to other exposed seats where there is a risk of the occupant being thrown forward; and
• correct the text of the Regulation.

Proposal to

1. extend requirements for exterior rear-view mirrors to camera monitor systems;
2. reduce the speed threshold for deactivation of emergency controls from 5 km/h to 3 km/h;
3. clarify the requirements concerning the height of steps in vehicles which comply with Annex 8;
4. limit the mandatory application of the requirements for dedicated areas for prams and pushchairs to Class I vehicles;
5. require activation of the alarm and fire suppression systems as soon as the heater is in function regardless of whether the engine is operating;
6. extend requirements for exposed seats adjacent to step wells to apply to other exposed seats where there is a risk of the occupant being thrown forward; and
7. correct the text of the Regulation.

Proposal to mandate fire suppression systems on Class I and II buses.

Proposal to remove the provisions for welded constructions of compressed natural gas (CNG) cylinders or metal liners, including high-strength steel CNG cylinders and consolidating the earlier proposal (from document WP.29/2015/90 that was adopted but set aside at the November 2015 WP.29 session pending the proposal on cylinder construction) to regulate the discharge direction of pressure relief devices on CNG containers.

This proposal clarifies that the provisions concern any cable used in the entire vehicle, not only to those in the interior compartment, engine compartment and separate heater compartment. The proposal also clarifies that the regulation applies not only to electric cables, but also to cable sleeves or cable conduits and it updates the reference to paragraph 5.22. of ISO 6722-1:2011. Specifically, the proposal would apply testing to electric cables, cable sleeves, and cable conduits that exceed a length of 100 mm.

Proposal to modify UN R125 in line with the amendment to UN R46 (indirect vision) that introduces the use of camera-monitor systems (CMS) in place of rear-view mirrors. This proposal also ends the temporary exemption permitting CMS device obstruction of driver field of view from 1 September 2021.

Proposal to align the provisions of Regulation No. 10 with the proposed amendments to Regulation No. 46 (Devices for indirect vision) to allow the replacement of rear-view mirrors by camera-monitor systems.

Proposal to align the provisions of Regulation No. 10 with the amendments to Regulation No. 46 (Devices for indirect vision) to allow the replacement of rear-view mirrors by camera-monitor systems.

Proposal to delete the requirement for automatic leveling devices for all headlamps with light emitting diode (LED) light sources based upon the results of the GTB glare study. The proposal argues that the restriction discriminates against LED light sources based upon an erroneous understanding of light-source relevance to driver glare.

Proposal to delete the requirement for automatic leveling devices for all headlamps with light emitting diode (LED) light sources based upon the results of the GTB glare study. The proposal argues that the restriction discriminates against LED light sources based upon an erroneous understanding of light-source relevance to driver glare.

Proposal to delete the requirement for automatic leveling devices for all headlamps with light emitting diode (LED) light sources based upon the results of the GTB glare study. The proposal argues that the restriction discriminates against LED light sources based upon an erroneous understanding of light-source relevance to driver glare.

Proposal to enable the approval of sequential activation of light sources of direction indicators lamps for motorcycles.

Proposal to allow for the approval on motorcycles of light-signalling devices with light sources that can be sequentially activated and of emergency stop signals.

Proposal to delete references to UN R113 Class B headlamps from the regulation.

Proposal for the establishment of a new UN Regulation governing the approval of audible vehicle alerting systems for quiet vehicles moving at low speeds. This proposal can be considered as the first phase of the regulation. In response to concerns raised by the World Blind Union, GRB agreed to extend the mandate of the informal working group that developed this text in order to consider further measures to address the WBU concerns.

Proposal to align the requirements of UN R113 with those adopted in Regulations Nos. 98, 112 and 123 relating to movement of the cut-off line after heat test and to correct an error in the provisions on the use of LED modules.

Proposal to introduce new Light Emitting Dodes (LED) light source categories LW3, LY3, LR5, LW5 and LY5 and to align some drawings of category LR4 with drawings of these new categories.

Proposal to allow for small variations in the presentation of motorcycle telltales and control symbols.

Proposal to correct the inadvertent deletion of a sentence in by WP.29/2015/57 adopted at the 166th session of the World Forum for Harmonization of Vehicle Regulations (WP.29).

Proposal to begin work on the second phase development of the light vehicle emissions GTR, covering:

• Remaining items from the original authorization (WP.29/AC.3/26)
• Open issues remaining under Phase 1b
• Durability of internal combustion engine vehicles and electric vehicles
• Evaporative emissions
• Low ambient temperature emissions
• Test procedure for the determination of additional CO2 emissions and fuel consumption from mobile air conditioning systems
• On-board diagnostics requirements
• Development of criteria for ex-post assessing of road load parameters (document WLTP-12-29-rev1e), and
• “Other items” as may arise.

Correction of the French text only of the 01 series of amendments to UN R73.

Declaration from the UN gathering of ministers during 18-19 November 2015, including item OP20. Promote the adoption of policies and measures to implement United Nations vehicle safety regulations or equivalent national standards to ensure that all new motor vehicles, meet applicable minimum regulations for occupant and other road users protection, with seat belts, air bags and active safety systems such as anti-lock braking system (ABS) and electronic stability control (ESC) fitted as standard.

Status of the proposals adopted during the June 2015 WP.29 session. Please note that the documents do not all have the same date of entry into force.

Proposal to develop an amendment to GTR No. 1 to provide alternatives to ensure adequate protection against accidental opening of the rear door while the vehicle is in motion.

While encouraged by the adoption of a uniform minimum sound alert standard, the WBU continues to believe that: 1) the proposed minimum sound standard is too low for safety; 2) the AVAS should remain on while the QRTV is active but stationary; and 3) the regulation should prohibit manufacturers from providing a means of pausing the alert sound.

Updated agenda including the latest informal document submissions

Brief summary of GRRF discussions related to the performance of products in conditions outside the scope of test procedures (i.e., assuring satisfactory performance under all normal road conditions). GRRF agreed with Russia that this issue should be put before the full World Forum.

Proposal from the Working Party on Dangerous Goods to delete paragraph 2.2.1 and 2.3.2 in Annex 5 of Regulation No. 13 permitting the use of an endurance braking system on a trailer to compensate for insufficient performance of the endurance braking system of the motor vehicles. Such systems have been prohibited by WP.15 such that alignment of the vehicle technical requirements is needed.

Proposal from Turkey to establish requirements for audible systems to alert other road users when a vehicle is operating in reverse.

The purpose of this paper is to provide a framework through which the delegates to the World Forum for the Harmonization of Vehicle Regulations (WP.29) and other interested stakeholders can examine the experience with the 1998 Global Agreement and agree on ideas and processes for improvement in its implementation. This version supersedes the previous documents WP.29-167-12 and WP.29/2015/108.

Brief update on automated vehicle policy in Korea and to highlight the importance of the WP.29’s role of coordinating with WP.1, ITU and other relevant agencies.

Proposal to clarify that conditioning of a silencing system is necessary only in cases where exhaust gases come into contact with silencer fibrous materials.

Proposal to clarify the test procedure by explicitly excluding first gear where possible from the ASEP control range and to clarify that conditioning of a silencing system is necessary only in cases where exhaust gases come into contact with silencer fibrous materials.

Proposal to clarify that conditioning of a silencing system is necessary only in cases where exhaust gases come into contact with silencer fibrous materials.

Proposal to specify that conditioning of a silencing system is necessary only in cases where exhaust gases come into contact with silencer fibrous materials.

Proposal to introduce provisions to prevent the unintentional opening of rear doors while the vehicle is in motion. The amendment address doors equipped with interior handles that would enable opening from inside the vehicle, including installation of locking systems.

Proposal to introduce provisions to prevent the unintentional opening of rear doors while the vehicle is in motion.

Proposal to introduce: (i) a definition of flexible shoulder adjustment device for height, (ii) provisions for its testing and (iii) to define its strict field of installation for vehicle categories M2 and M3.

Proposal to introduce (i) a definition of flexible shoulder adjustment device for height, (ii) provisions for its testing and (iii) to define its strict field of installation for vehicle categories M2 and M3.

Proposal to limit the use of a booster cushion (booster seat without backrest) with children of a stature greater than 125 cm (i.e., prohibit use of booster cushion for children under 125 cm) and the application for type approval of such CRS only in mass Group III for children of mass from 22 kg to 36 kg and to clarify that a guide strap which constrains the shoulder strap of the adult seat belt in a position to suit the child in a child restraint system cannot be approved as a separate CRS under UN R44.

Proposal to define provisions for “Integral” and “Non-Integral” Enhanced Child Restraint Systems (ECRS). “Integral” refers to systems where the child is restrained only by components which comprise the ECRS (e.g. strap harness, impact shield, etc.), and not by means connected directly to the vehicle (e.g. adult seat belt). “Non-Integral”, then, refers to systems where the child is retained by use of the adult seat belt connected directly to the vehicle. This proposal represents “Phase 1” in the development of UN R129.

Proposal to correct a reference in UN R134, Annex 3, paragraph 3.4. The reference to paragraph 6.2.2.2. was transposed from GTR No. 13; however, it ostensibly refers paragraph 2.2 of Annex 3 in UN R134.

Proposal to align the requirements related to measurement equipment linearity verification in Regulation No. 49 to the provisions in Regulation No. 96.

Proposal to

• align the requirements related to measurement equipment linearity verification with the Regulation No. 96,
• adapt the requirements related to fuel injection malfunction monitoring (On-Board Diagnostic systems) to the current state of technology, and
• correct the documentation requirements for off-cycle emissions.

Proposal to correct the calculation of the coast-down resistance to progress force.

Proposal to correct the calculation of the coast-down resistance to progress force.

Proposal to simplify the communication model of approval under UN Regulation No. 115.

Proposal for corrections to the text and equations.

Proposal to delete provisions for electronic stability and brake-assist systems from UN R13-H as part of their transposition into new stand-alone regulations. This proposal also clarifies the requirements on electromagnetic compatibility via reference to Regulation No. 10.

Proposal to

• amend the tyre dimensional requirements,
• amend the requirements for the load/speed performance test,
• align definitions and content with the other tyre regulations (UN Regulations Nos. 117, 54, 75 etc.),
• include a definition of “manufacturer” extracted from the resolution R.E.3,
• adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links, and
• add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Proposal to:

• correct the code 19 rim diameter, amend the tyre dimension requirements,
• modify the marking requirements to replace PSI with kilopascals (“kPa”),
• change the measurement units for drum speed from min-1 to km.h-1 and align the wording in Annex 7, Appendix 1 with the text of the Regulation,
• add new tyre sizes to Annex 5, allow for special tyres that can also be used as snow tyres to be marked with the inscription M+S, M.S, or M&S while remaining in the category of use “special”,
• align definitions and content with the other tyre regulations (UN Regulations Nos. 30, 117, 75 etc.),
• include a definition of “manufacturer” extracted from the resolution “R.E.3”
• adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links, and
• add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Proposal to ensure that coupling balls do not block rear lighting and/or registration plates.

Proposal to remove tyre pressure monitoring systems from UN R64 pursuant to establishing a stand-alone regulation and to facilitate the development of the regulation on international whole vehicle type approvals.

Proposal to amend the tyre dimension requirements.

Proposal to include three-wheeled category L vehicles within the scope of ABS testing, to align UN R78 with the provisions for anti-lock braking systems used in other regulations, including specific exemptions for certain off-road vehicles as incorporated in UN Regulation No. 13, and to allow for Emergency Stop Signal (ESS) systems on motorcycles and related vehicles. The proposal also clarifies the limits on the use of any temporary ABS deactivation switch and prohibition against permanent disabling of ABS if fitted on a motorcycle.

Proposal to remove certain design restrictions that impede the application of new technologies, especially related to trailer power steering systems and the use of energy from the towing vehicle, including specification of the connector through which electrical energy is supplied in the proposal. This proposal also replaces references to rear-view mirrors with the term “indirect vision devices” to reflect the addition of camera-monitor systems to UN R46 and clarifies the references to Regulation No. 10 on electromagnetic compatibility requirements.

Proposal to introduce provisions for the approval of replacement brake discs for L-category (motorcycle and related) vehicles, to remove tables specifying general values for replacement discs and drums that are identical to the original, change the maximum permitted thickness variation of discs for medium and heavy vehicles from 0.030 mm to 0.040 mm, and clarify the text in order to avoid additional administrative and financial costs to the applicant due to misinterpretation of the intent of the text.

Proposal to align UN R106 with international standards (ETRTO, T&RA and ISO 4351-2 table 2) with regard to Improved Flexion (IF) tyres and Very high Flexion (VF) tyres to add load indexes to the table in the Annex 4 to keep up with the technical evolution of tyres. This proposal also clarifies the application of EC Regulation 167/2013 which refers to UN R106.

Proposal to:
a) Align definitions and content with the other tyre regulations (UN Regulations Nos. 30, 54, 75 etc.);
b) Include a definition of “manufacturer” extracted from the resolution “R.E.3”;
c) Adopt a common definition and use of the terms “Manufacturer’s name”, “Brand name”, “Trademark”, “Trade description” and “Commercial name” and their links; and
d) Add information in the certificate to enable approval authorities to more easily understand the products the certificate addresses.

Proposal for a new UN Regulation based upon brake-assist system provisions extracted from UN R13-H in order to facilitate work on the international whole vehicle type approval system.

Proposal for a new UN Regulation comprised of provisions concerning electronic stability control systems extracted from UN R13-H in order to facilitate work on the international whole vehicle type approval system.

Proposal for a new UN Regulation on tire installation for use within the International Whole Vehicle Type Approval system.

Proposal for a Special Resolution to provide a framework within which the representatives of the World Forum for the Harmonization of Vehicle Regulations (WP.29) and other interested stakeholders can work to improve the implementation of the 1998 Global Agreement.

Technical report on the development of draft global technical regulation on the measurement procedure for two- or three-wheeled motor vehicles equipped with a combustion engine with regard to the crankcase and evaporative emissions

Proposed amendment to complete the Phase 1 development of the light vehicle emissions GTR. This amendment addresses:

• Conventional ICE vehicles
  • Normalisation methods and speed trace index;
  • Number of tests;
  • Wind tunnel as alternative method for road load determination;
  • Road load matrix family;
  • Interpolation family and road load family concept;
  • On-board anemometry and wind speed conditions;
  • Alternative vehicle warm-up procedure; and
  • Calculation and interpolation of fuel consumption.
• Electrified Vehicles
  • Fuel cell vehicle test procedure;
  • Shortened test procedure for PEV range test;
  • Phase-specific CO2 (fuel consumption) for Off-Vehicle Charging Hybrid Electric Vehicles (OVC-HEVs);
  • End of EV range criteria;
  • Interpolation approach for OVC-HEVs and PEVs;
  • Utility factors; and
  • Predominant mode / mode selection.
• Alternative pollutants
  • Measurement method for ammonia, ethanol, formaldehyde and acetaldehyde.
• Development of Harmonized Cycle (DHC)
  • Further downscaling in Wide Open Throttle (WOT) operation; and
  • Gear shifting.

Detailed report on the decisions and rationale involved in the development of the amendment to complete the Phase 1 development of the global technical regulation on light vehicle emissions.

Proposal of Amendment 1 to UN GTR No. 16 to include new provisions on wet grip performance, rolling resistance, and qualification of tires for use in severe snow conditions for passenger cars and light trucks/commercial vehicles. The amendment also reflects recent changes adopted in US Federal Motor Vehicle Safety Standards (tire strength and tubeless tire bead unseating resistance) and UN Regulations Nos. 30 and 54.

Proposal for the explanatory report detailing the decisions and rationale involved in the development of Amendment 1 to the GTR on passenger and light truck/commercial vehicle tires.

Request for authorization to develop an amendment to GTR No. 1 to ensure adequate protection against accidental opening of the back door while the vehicle is in motion.

Proposal to begin work on the second phase development of the light vehicle emissions GTR, covering:

• Remaining items from the original authorization (WP.29/AC.3/26)
• Open issues remaining under Phase 1b
• Durability of internal combustion engine vehicles and electric vehicles
• Evaporative emissions
• Low ambient temperature emissions
• Test procedure for the determination of additional CO2 emissions and fuel consumption from mobile air conditioning systems
• On-board diagnostics requirements
• Development of criteria for ex-post assessing of road load parameters (document WLTP-12-29-rev1e), and
• “Other items” as may arise.

Proposal to align the requirements of UN R113 with those adopted in Regulations Nos. 98, 112 and 123 relating to movement of the cut-off line after heat test and to correct an error in the provisions on the use of LED modules.

Addition of agenda items concerning a proposal for Supplement 6 to the 01 series of amendments to Regulation No. 113 a proposal for Special Resolution No. 2 (S.R.2) on a framework to improve the effectiveness of the 1998 Agreement.

Informal updated version as of 14 June 2016 (Track changes version)

Proposal to harmonize the provisions of UN Rule No. 1 with those of the latest UN Regulations annexed to the 1958 Agreement and the EU vehicle inspection Directives.

Proposal to harmonize the provisions of UN Rule No. 2 with those of the latest UN Regulations annexed to the 1958 Agreement and EU vehicle inspection Directives.

Proposal for an amendment to update global technical regulation (GTR) No. 9 in line with technical progress, notably to provide a test procedure for deployable systems of the outer surface of vehicles to ensure an adequate protection of pedestrians or other vulnerable road users during the accident.

Paper by the WP.29 secretariat to outline possibilities for regulatory provisions covering the performance of automotive systems under conditions other than those tested in the framework of type-approval or self-certification, with TPMS as a case study.

Revised calendar of meetings following confirmation by the UNOG conference services bureau.

Proposal developed by the GRE Task Force on Tell-tales and approved by the GRE to clarify that the use of lamps designed for only two light sources is restricted to vehicles fitted with a tell-tale that will indicate when any one of the two lights sources has failed.

Proposal from the Informal Working Group “Simplification of the Lighting and Light-Signalling Regulations” (SLR) and approved by the GRE to simplify the content and amendment process of the light source Regulations in conjunction with the establishment of a new resolution on specifications for light source categories.

Proposal to amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45 where the specified quantity of “2 ± 1 parts by weight” of surfactant results in invalid testing. The correct specification should be “2 ± 1 drops” of surfactant.

Proposal from the GRE Task Force on Tell-Tales and approved by GRE for Supplement 17 to the 04 series of amendments to UN R48 in order to clarify failure tell-tale requirements. The proposal also includes an amendment to clarify paragraph 6.21.1.2.4. with regard to the application of conspicuity markings on bodywork made of flexible material.

Proposal from the GRE Task Force on Tell-Tales and approved by GRE for Supplement 10 to the 05 series of amendments to UN R48 in order to clarify failure tell-tale requirements. The proposal also includes an amendment to clarify paragraph 6.21.1.2.4. with regard to the application of conspicuity markings on bodywork made of flexible material.

Proposal from the GRE Task Force on Tell-Tales and approved by GRE for Supplement 8 to the 06 series of amendments to UN R48 in order to clarify failure tell-tale requirements. The proposal also includes an amendment to clarify paragraph 6.21.1.2.4. with regard to the application of conspicuity markings on bodywork made of flexible material.

Proposal to remove restrictions that impede the use of bend lighting on motorcycles. UN R53 currently prohibits the use of additional lighting units when the driving beam is in use. This requirement unnecessarily restricts the use of ALU to improve road illumination at night when the motorcycle is banking through a turn.

Proposal to remove restrictions that impede the use of bend lighting on motorcycles. UN R53 currently prohibits the use of additional lighting units when the driving beam is in use. This requirement unnecessarily restricts the use of ALU to improve road illumination at night when the motorcycle is banking through a turn.

Proposal by the GRE Informal Group “Agricultural Vehicles Lighting Installation” (AVLI), approved by GRE, to update and revise Regulation No. 86. The proposal applies the regulation to vehicle categories R and S as defined under the Consolidated Resolution on the Construction of Vehicles (RE3), updates geometric visibility provisions, and adds new provisions and new Annex 6 on signalling panels and signalling foils .

Proposal from the Task Force on Tell-Tales, approved by GRE, to clarify the requirements for failure indication.

Proposal from the Informal Working Group “Simplification of the Lighting and Light-Signalling Regulations” (SLR), approved by GRE, to amend UN R99 in conjunction with the program to simplify the content and amendment process of the light source Regulations.

Proposal from the Informal Working Group “Simplification of the Lighting and Light-Signalling Regulations” (SLR), approved by GRE, to amend UN R128 in conjunction with the program to simplify the content and amendment process of the light source Regulations.

Proposal to harmonize the provisions of UN Rule No. 1 with those of the latest UN Regulations annexed to the 1958 Agreement and the EU Directives.

Proposal to harmonize the provisions of UN Rule No. 2 with those of the latest UN Regulations annexed to the 1958 Agreement and the EU Directives.

Proposal to change the latency for scanning a field of vision (total process of scanning, rendering and reset to its initial position) from a maximum of 2 seconds to a maximum of 200 ms. This proposal corresponds to the current state of technology and removes a contradiction within the regulation between paragraphs 6.2.1.2. and 6.2.2.3.4.3. (the latter introduced via supplement 2 to the 04 series of amendments).

Proposal prepared by the UNECE secretariat to align the provisions of UN Regulation No. 105 with those of the new 2017 edition of the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR).

Proposal to clarify paragraph 7.7.5.1. with regard to ceiling-mounted displays or monitors and simplify the testing procedure:

• The gauge shall be used only for the identification of the monitors to be tested.
• The simplified way to apply the removal force corresponds to a passenger pushing the monitor/display with its hand, and in these conditions the acceptable force limit is adapted.
• The test must be conducted in both directions.
• The proposed wording for the last condition to fulfil is more technology neutral, the case of automatic redeployment is also considered and banned.

Proposal to extend requirements introduced via Supplement 4 to the 04 series of amendments concerning barriers in the gangway and the amount of priority seats to the 05 series of amendments.

The proposal also aims to paragraph 7.7.5.1. with regard to ceiling-mounted displays or monitors and simplify the testing procedure:

• The gauge shall be used only for the identification of the monitors to be tested.
• The simplified way to apply the removal force corresponds to a passenger pushing the monitor/display with its hand, and in these conditions the acceptable force limit is adapted.
• The test must be conducted in both directions.
• The proposed wording for the last condition to fulfil is more technology neutral, the case of automatic redeployment is also considered and banned.

Proposal to extend requirements introduced via Supplement 4 to the 04 series of amendments concerning barriers in the gangway and the amount of priority seats to the 06 series of amendments.

The proposal also aims to paragraph 7.7.5.1. with regard to ceiling-mounted displays or monitors and simplify the testing procedure:

• The gauge shall be used only for the identification of the monitors to be tested.
• The simplified way to apply the removal force corresponds to a passenger pushing the monitor/display with its hand, and in these conditions the acceptable force limit is adapted.
• The test must be conducted in both directions.
• The proposed wording for the last condition to fulfil is more technology neutral, the case of automatic redeployment is also considered and banned.

Proposal to extend requirements introduced via Supplement 4 to the 04 series of amendments concerning barriers in the gangway and the amount of priority seats to the 07 series of amendments.

The proposal also aims to paragraph 7.7.5.1. with regard to ceiling-mounted displays or monitors and simplify the testing procedure:

• The gauge shall be used only for the identification of the monitors to be tested.
• The simplified way to apply the removal force corresponds to a passenger pushing the monitor/display with its hand, and in these conditions the acceptable force limit is adapted.
• The test must be conducted in both directions.
• The proposed wording for the last condition to fulfil is more technology neutral, the case of automatic redeployment is also considered and banned.

Proposal to

1. enable the use of autonomous CNG heaters for the heating of engines before the vehicle is in service
2. allow the use of Class 0 hoses with couplings using sealing technologies other than those with a 45° cone
3. correct a typographical error in paragraph 7.1. where the reference should be to paragraph 8.22 rather than 8.21
4. remove a duplicate and contradictory reference in Annex 4A to the requirements of Class 1 pressure relief valves
5. align paragraph 2.2. of Annex 4H with paragraph 18.6.1.2. limiting the delay in switching-off of the automatic valve after stalling of the engine to two seconds (rather than five as presently in the text), and
6. include the liquefied natural gas (LNG) fuel connector provisions as specified in ISO 12617:2015.

Proposal to enable the use of alternate colors (per footnote 18 of Table 1 and in line with ISO Standard 2575) for certain lighting tell-tales in order to indicate light source failures in response to the proposals for light failure indicators under UN Regulations Nos. 7, 48 and 87 (GRE/2016/7, GRE/2016/12 and GRE/2016/17) as adopted by GRE. This proposal anticipates use of the same approach in response to plans for additional failure indication requirements for other lighting regulations.

Proposal to enable the use of alternate colors (per footnote 18 of Table 1 and in line with ISO Standard 2575) for certain lighting tell-tales in order to indicate light source failures in response to the proposals for light failure indicators under UN Regulations Nos. 7, 48 and 87 (GRE/2016/7, GRE/2016/12 and GRE/2016/17) as adopted by GRE. This proposal anticipates use of the same approach in response to plans for additional failure indication requirements for other lighting regulations.

Proposal to clarify and improve provisions for

1. the belt routing and positioning of the universal child restraint system seat fixture during testing;
2. dynamic testing of the rear seat system and advanced restraint system approval; and
3. to restructure and simplify the consumer information requirements on the installation of ISOFIX child restraint systems under UN R16.

Proposal to require seat-belt reminders for all seating positions, including rear positions, and to clarify the scope of the regulation.

Proposal to improve the translation into Russian of the text originally adopted in its English version and to correct a typographical error in the Russian text.

Proposal to amend the toxicity and flammability declarations via references to EN 71 (European safety standards), taking into account procedures of FMVSS 302. The amendments propose the burning rate values of FMVSS 302 (302.4 inches/102 mm per minute), to harmonize the three proposals with regard to EN standards references, and to incorporate the amendment 1 to EN 71-3 (A1:2014).

The proposal also would align requirements for deceleration test devices with acceleration ones (making explicit that it is mandatory to match the corridor for each test) and to add dummy criteria and compliance with ISO 17025 to the information required in test reports.

Proposal to strip ISOFIX CRS provisions from UN R44 and to cease all new type approvals for ISOFIX integral CRS under UN R44 from 1 September 2017 in deference to UN R129 on Enhanced CRS.

UN R80, paragraph 7.4.4. specifies that passengers in side-facing seats “shall be safeguarded by a vehicle part (e.g. partition, wall or seat back of a forward-facing seat) forward of the foremost side-facing seat”. Germany has determined that the current text has been misinterpreted with regard to the intended requirement for a safety device that does not break and maintains its capability to retain a passenger’s body in the event of an accident. This proposal clarifies that such any such structure “shall retain its safeguard function during testing”.

Proposal to improve the translation into Russian of the text originally adopted in its English version and to correct a typographical error in the Russian text.

Proposal to

1. amend the toxicity and flammability declarations via references to EN71 (European safety standards)
2. align paragraph 6.6.3.1. with the 01 series of amendments,
3. to align requirements in 7.1.3.1 to test methods in 8.1.2.4.,
4. add tolerances to better define the test method in paragraph 8.1.2.3.,
5. improve the specifications for the measurement of dimensions C and D in Annex 23,
6. align deceleration test requirements with acceleration test provisions (making explicit that it is mandatory to match the corridor for each test, and
7. define the initial acceleration value under paragraph 7.3. against which the maximum deviation restriction is to be applied.

Proposal to amend the toxicity and flammability provisions.

Proposal to introduce CRS Informal Group “phase 2” amendments regarding the approval of booster-seat CRS category (booster seat with backrest) into UN R129.

UN Regulations Nos. 49 and 83 include provisions for a “driver inducement system” that alerts drivers of low reagent levels (urea, etc.) critical to correct emissions control performance and eventually prevents vehicle operation if the reagent tank is empty. Under UN R49 (para. 5.2), rescue, police, and other emergency/special use vehicles are exempted from this requirement. This proposal would extend the same treatment under UN R83. The proposal also makes several corrections and clarifications (see document GRPE/2016/11) with respect to extensions of approval, reduction in efficiency of the catalytic converter with respect to emissions of NMHC and NOx, and OBD.

UN Regulations Nos. 49 and 83 include provisions for a “driver inducement system” that alerts drivers of low reagent levels (urea, etc.) critical to correct emissions control performance and eventually prevents vehicle operation if the reagent tank is empty. Under UN R49 (para. 5.2), rescue, police, and other emergency/special use vehicles are exempted from this requirement. This proposal would extend the same treatment under UN R83. The proposal also makes several corrections and clarifications (see document GRPE/2016/11) with respect to extensions of approval, reduction in efficiency of the catalytic converter with respect to emissions of NMHC and NOx, and OBD.

Proposal for a new Regulation on uniform provisions concerning the approval of Heavy Duty Dual-Fuel Engine Retrofit Systems (HDDF-ERS) to be installed on heavy duty diesel engines and vehicles. Please note that Japan notified the UN Secretary-General on 1 February 2017 of its intention not to apply this regulation from the date it enters into effect (June 2017). Japan remains free to adopt the regulation at a later date.

Proposal for a new Consolidated Resolution to simplify the content and amendment process of the light source Regulations Nos. 37, 99 and 128. The data sheets for light sources are moved from Annex 1 of these Regulations to the draft Resolution.

Proposal to align the text with the provisions for anti-lock braking systems used in other regulations, including specific exemptions for certain off-road vehicles as incorporated in UN Regulation No. 13. The proposal clarifies the limits on the use of any temporary ABS deactivation switch and prohibition against permanent disabling of ABS if fitted on a motorcycle.

Proposal to develop a test procedure for the assessment of exterior (outer surface of the vehicle) deployable systems to protect pedestrians or other vulnerable road users during an accident.

Proposal to amend document WP.29/2016/98. The proposal clarifies the subject of paragraph 12.1 and corrects an editorial error concerning the repetition of footnote 2 that exists already in Annex 1B to Regulation 16.

Proposal from GRRF to correct document WP.29/2016/114 (proposal to align UN R78 with other braking regulations as regards anti-lock braking systems and to clarify the limits on the use of any temporary ABS deactivation switch and prohibition against permanent disabling of ABS if fitted on a motorcycle. Under (e), the correct reference to the paragraph GTR No. 3 should read 5.1.13. The correct reference under f) to the previous points should be (a) to (e) instead of (a) to (f).

Proposal to develop an amendment in order to align GTR No. 3 with technical progress, addressing among others: ensuring electromagnetic immunity of ABS-systems, introducing ABS performance requirements for category 3-5 vehicles (three-wheelers), ensuring uniform requirements for equipment such as Electronic Stop Signal System and the means to disable the ABS, if equipped. This amendment aims to harmonize GTR with recent amendments made to UN Regulation No. 78.

Form for use in Establishment of the Executive Committee AC.3 under the 1998 Agreement (item 12) and Consideration and vote by AC.3 (item 14)

Proposal to develop amendments to Part II of GTR No.16:

1. Addition of new definitions (Section 2);
2. Harmonization of the Load Range concept in relationship to Inflation Pressure (Section 2),
3. Alignment of the provisions for tyre marking and physical dimensions of PC tyres with the most recent developments in UN Regulations Nos. 30 and 54 (Sections 3.3 and 3.5),
4. Harmonization of FMVSS 139 requirements relative to UNECE PSI index (Sections 3.14 and 3.15),
5. Deletion of provisions for physical dimensions of LT/C tyres based on FMVSS 139 (Section 3.20) an UN Regulation No. 54 (Section 3.21) and addition of new harmonized provisions for physical dimensions of LT/C tyres (new Section 3.20),
6. Deletion of provisions for high speed test for LT/C tyres based on FMVSS 139 (Section 3.19) and UN Regulation No. 54 (Section 3.16) and addition of new harmonized provisions for high speed test for LT/C tyres (new Section 3.16),
7. Updates of the Annexes 3 and 6 with regard to the most recent developments in UN Regulations Nos. 30 and 54.

Other topics to be discussed within the informal working group for the Phase 2 of development of UN GTR No. 16 include:

1. Consideration of feasibility of harmonization of endurance test for LT/C tyres (Sections 3.16 and 3.17), and
2. Consideration of feasibility of development of provisions for global tyre marking.

During the 169th session of WP.29 (para. 39 of the session report), the World Forum was informed that, following the entry into force of the new European legislation on provisions on real driving emissions and Worldwide Harmonized Light Vehicle Test Procedure (WLTP) as of September 2017, no new vehicles will be allowed to enter into the European market without fulfilling these new provisions.

WP.29 agreed to introduce transitional provisions in UN Regulations Nos. 83 and 101 to specify that Contracting Parties applying UN Regulations Nos. 83 and 101 which would also apply WLTP as defined in UN GTR No. 15 (such as the EU) would have no obligation to accept type-approvals granted on the basis of test cycles other than WLTP as of September 2017 (para. 41 of the 169th session report). WP.29 requested the secretariat to prepare an official document for the WP.29 March 2017 session, subject to the endorsement of GRPE at its January 2017 session, on supplements to UN Regulations Nos. 83 and 101 introducing such transitional provisions.

Thus, the secretariat has prepared this text to allow for such a derogation from mutual recognition requirements under UN R83 and R101 until such time as GTR 15 has been transposed into UN Regulations under the 1958 Agreement.

Proposal from the informal working group on Periodical Technical Inspections to introduce provisions, including a new Appendix 3, concerning requirements for the inspection process (testing centres, test equipment, and inspector qualifications).