Replace the proposal for Supplement 3 of the 05 Series of amendments

Proposal to replace the Supplement 11 of the 04 Series of amendments

Proposal to replace proposal for Supplement 6 of the 02 Series of amendments

Proposal to replace document ECE/TRANS/WP.29/GRBP/2024/06

Proposal to replace document ECE/TRANS/WP.29/GRBP/2024/09

Proposal to replace document ECE/TRANS/WP.29/GRBP/2024/07

Proposal to replace document ECE/TRANS/WP.29/GRBP/2024/13

Consolidated version including the amendments proposed with document ECE/TRANS/WP.29/GRBP/2024/13 amended by GRBP-79-24.

Proposal to replace document ECE/TRANS/WP.29/GRBP/2024/03

Consolidated version including the amendments proposed with document ECE/TRANS/WP.29/GRBP/2024/03 amended by GRBP-79-26..

This consolidated document amends and supersedes GRBP/2024/11.

This document supersedes the proposal in ECE/TRANS/WP.29/GRBP/2024/16

Amendments from the Task Force on Tyre Abrasion (TFTA) to the proposal to introduce test methods to measure tyre abrasion.

Consolidated version including the amendments proposed with document ECE/TRANS/WP.29/GRBP/2024/11 amended by GRBP-79-28-Rev.1.

In introducing ASEP in Annex 7 in 2016, the scope was limited to vehicles with internal combustion engines (ICE) based on the experience of variabilities in the exhaust silencing systems. Electric driven vehicles have been exempted from ASEP. For electric driven vehicles the new UN Regulation No. 138, dealing with the reduced audibility of these vehicles, was worked out until 2017. At that moment no one expected sound enhancement systems beyond the scope and aim of UN R138.

This proposal is an approach to address the concern that electric vehicles might be equipped with sound enhancement systems beyond the scope and aim of UN R138. This proposal does not require any changes to UN R138.01. This proposal is given as a supplement to enable the quickest entry into force, providing all manufacturers clear direction on the design of sound enhancement systems.

Some corrections and clarifications concerning power definition, calibration, temperature correction and Reference sound assessment

Updated proposal for a 02 series of amendments to specify the working principles of an Acoustic Vehicle Alerting System (AVAS) and to reduce measurement uncertainties during the measurement of the one third octave bands.

Proposal to clarify the text:

• clarify Annex 4 and exclude aluminum-alloy and magnesium-alloy wheels under test (b)
• clarify Annex 6 with regard to possible defects caused by the production process and not affecting the appearance of cracks during testing
• recommend under Annex 6 to identify cracks occurred as a result of the test by using penetrating paints
• clarify Annexes 7 and 8 with regard to air leakage.

Proposal to clarify that the maximum sound pressure requirement at the front plane at standstill condition in reverse shall be equal to the maximum level requirement in motion (defined by the QRTV task force as 75 dB(A) for both standstill and reverse driving).

Proposal to correct an omission and clarify the text of Annex 3: The positioning and order of the markings shall be as follows:….

Proposal from the Wet Grip on Worn Tyres informal group to standardize provisions for the water depth measurement and to reduce the track friction range requirements under the test procedures.

Proposal to clarify that wet adhesion provisions apply to C1, C2, and C3 tyres, correct ISO and internal references, clarify symbols “ARC” and “ARR” relationships to indoor drum test method, and clarify application to M+S marked tyres.

Proposal to clarify the requirements for non-original replacement exhaust silencing systems (NORESS).

Correction to the French version of the document which had a missing text in Annex 5 Table 7.

Proposal to clarify that FRT tyres shall not be fitted to front steering and drive axles of motor vehicles.

IWG RD-ASEP has two parts:
A) RD-ASEP for UN-R51, to develop a mandatory procedure after the
monitoring phase
B) RD-ASEP for UN-R41: ASEP second step, to develop stricter ASEP limit
curves

This proposal aims at aligning the emission of AVAS sounds with safety needs

Proposal prepared by the experts from the IWG RD-ASEP in order to clarify the application of the Annex 7 ASEP testing conditions of motorcycles.

Proposal by the IWG WGWT to replace document ECE/TRANS/WP.29/GRBP/2024/23. This proposal aims as a first step to standardize the water depth measurement.

Proposal to delete this footnote 2 from the regulation

Gives the objective and rules of procedure of TF

Transmitted by the experts of TF-AVRS for amendments to take automated vehicles into considerations

EC counter-proposal on the introduction of EVs in the scope of ASEP

EC resulting position to
• limit the emission of AVAS to what is strictly necessary for safety
• corollary: prohibit unnecessary noise

ETRTO recommends to create a GRBP GOIE (Group of Interested Experts) involving CP’s
and NGO’s and with the goal to present an Informal Document by GRBP February 2025
session to validate the concept to be followed and implemented in a Working Document
by September 2025

The proposal provides a more clear indication by introducing the definition of “Front axle” so that it clarifies the interpretation of front steering axle.

Proposal to clarify the original intent of the Task Force on Quiet Road Transport Vehicles (TF QRTV) conclusion

Presentation by the IWG WGWT on the proposal to replace document ECE/TRANS/WP.29/GRBP/2024/23 by GRBP-80-11

This document for reference might be applied to measurement procedures
used in UN regulations of the Working Party on Noise and Tyres (GRBP).
It supports the definition of limit values during the development of
regulations by transparently presenting the measurement uncertainties
embodied in the measurement procedures during type approval,
conformity of production and other measurement reasons. Replaces GRBP/2024/08

Gives the background to proposal for the Application of Noise Limits to EVs fitted with Exterior Sound Enhancement Systems (ESES) to UN R51

The text reproduced below was prepared by the experts from OICA in order to address the original intent of the Task Force on Quiet Road Transport Vehicles (TF QRTV). This proposes to expand the speed range of ASEP forBEVs down to speeds > 0 km/h.

Presentation to support ECE/TRANS/WP.29/GRBP/2024/20

Proposal to amend document GRBP/2024/21

TF-VS, RD ASEP IWG for 4 Wheel vehicle and 2 wheel vehicle, TF-AVRS

Proposal for amendments to enable the application of UN R28 to ADS vehicles.

Proposal for amendments to enable the application of UN R138 to ADS vehicles.

Proposal to clarify the application of the Annex 7 ASEP testing conditions of motorcycles.

Proposal to update the RD-ASEP limit line following the revisions of the test procedures implemented by the 05 series of amendments.

Proposal to strengthen provisions against test defeating and to facilitate Conformity of Production testing.

Proposal to strengthen provisions against test defeating, to facilitate Conformity of Production testing, and to correct the communication document.

Proposal to allow the use of the test track as specified in ISO 10844:2021.

Proposal to:

1. Update reference to ISO 4000-1:2024 (published in March 2024)
2. Clarify the structure indication within the tyre size designation for run flat or self-supporting tyres suitable for speeds in excess of 240 km/h (inscription “ZRF”)
3. Clarify the nominal rim diameter.
4. Amend the definition of principal grooves by eliminating the circular reference between this definition and the position of tread wear indicators.
5. Introduce definition of tread depth (used in the requirements for special use and professional off-road tyres)
6. Clarify the calculation of tyre section width
7. Claify the D_max requirement for snow tyres.

Proposal to

1. 1. Add a generic reference to the Consolidated Resolution on the Construction of Vehicles (R.E.3) in footnote 1
2. Make editorial corrections to the type of tyre and additional service description definitions
3. Clarify the definition of nominal rim diameter (in line with the proposal for amending UN R30)
4. Amend the definition of principal grooves (in line with the proposal for amending UN R30
5. Introduce a definition for tread depth (used in the requirements for special use and professional off-road tyres)
6. Introduce definition for free rolling tyre and front axle, and related revision of markings (ref. GRBP-80-03 and GRBP-80-26)
7. Clarify the D_max requirement for snow tyres
8. Simplify rhz wording of the requirements for professional off-road tyres
9. Add an indication for whether a special use tyre is a professional off-road tyre to the communication form (in line with UN R30).

Proposal to

1. Add a generic reference to the Consolidated Resolution on the Construction of Vehicles (R.E.3) in footnote 5.
2. align the categories of use to “normal tyre”, “snow tyre” and “specialuse tyre” in line with UN R30 and 54, to introduce a definition of “normal
   tyre” and consequently make use of the terms “snow tyre” and “special-use tyre” that are already defined
3. reformat Annex 5, Table 7 to present the tyre-size designations in a consistent way and to provide explicitly that tyre-size designations from this table may also be used for tyres in bias-beltedvstructure
4. Include the suffix “M/C” that is defined as mandatory for motor-cycle tyres with rim diameter code 13 and above in the figure illustrating the sidewall markings in Annex 3 and to present the markings in a clearer way
5. Add provisions for the dimensional requirements of moped tyres
6. Add a factor for the centrifugal radius of snow tyres and special-use tyres with a speed category above 210 km/h
7. Give the footnotes in the main body of the regulation an unequivocal number to avoid confusion when referencing to a particular footnote
8. Include several editorial corrections to increase the consistency of the text (e.g. consistent use of the terms defined in section 2, such as “tyre-size designation”, “load-capacity index”, “speed-category symbol”).

Proposal to

1. Update standard reference to ASTM F2493-24 and ISO 4000-1:2024
2. Align the definitions of tread groove and principal grooves with proposals for UN R30 and R54
3. Simplify the wording of the requirements for professional off-road tyres
4. Correct the transitional provision in paragraph 12.23. to specify approvals “first issued after 31 August 2028”.

Proposal to

1. Clarfy the scope to reflect that adhesion performance on wet surfaces (wet adhesion) is required not only for C1 tyres, but also C2 and C3 tyres
2. Update standard reference to ASTM F2493-244, F3611-24, F3676-24, F3675-24 and ISO 4000-1:2024
3. Align the definitions of tread groove and principal grooves with proposals for UN R30 and R54
4. Simplify the wording of the requirements for professional off-road tyres
5. Correct the transitional provision in paragraph 12.23. to specify approvals “first issued after 31 August 2028”.

Proposal to:

1. Add a generic reference to the Consolidated Resolution on the Construction of Vehicles (R.E.3) in footnote 1
2. Align title of para. 5 with its contents (paras. 5.1. and 5.2.)
Align the title of para. 6 with corresponding paras. in UN R30, 54, 75, 106 and 117</li<
3. Clarify that all temporary use spare units can by composed by using tyres of any category of use
4. Align the snow tyre definition with UN R30, 54 and 117
5. Clarify that tyres for use in severe snow conditions are also applicable to the category of use ‘special use tyres’
6. Clarify which service conditions can apply the coefficient given in paragraphs 5.2.4.3.1. and 5.2.4.3.2.
7. Add Class C3 tyres to the speed category symbol and load capacity index definitions
8. Introduce definitions of free rolling tyre and front axle and revise markings accordingly (ref. documents GRBP-80-03 and GRBP-80-26)
9. Clarify reporting the name of the symbols used for tyre for use in severe snow conditions in line with UN R117 and 164.

Proposal to:

1. Correct the description of a tyre to exclude aspects outside the scope of UN R108
2. Align the snow tyre definition to UN R109 and 172
3. Clarify the definition of nominal rim diameter
4. Clarify the definition of principal grooves by eliminating the circular reference between this definition and the position of tread wear indicators
5. Introduce a definition for tread depth (used in the requirements for special use and professional off-road tyres)
6. Amend para. 4.1.5.3.2. to remove the retreaded reference to traction tyre classification because it is not applicable to tyre of class C1
7. Clarify the calculation of the tyre section width
8. Replace “XXX” with the UN Regulation No. 172 in the references to the approval of retreaded tyres with regard to their snow performance and/or classification as traction tyre.

Proposal to:

1. Correct the description of a tyre to exclude aspects outside the scope of UN R109
2. Clarify the definition of nominal rim diameter
3. Clarify the definition of principal grooves in line with the proposal for UN R54
4. Amend para. 6.4.4.2. to clarify that the UN R117 certificate may be used for obtaining the type approval under UN R172 of retreaded tyres classified as traction tyre
5. Simplify the wording of the requirements for professional off-road tyres
6. Replace “XXX” with the UN Regulation No. 172 in the references to the approval of retreaded tyres with regard to their snow performance and/or classification as traction tyre.

Proposal to:

1. Add new reference tyres C3 SRTTs 19.5 and 22.5 siped and related transitional provisions
2. Simplify the wording of the requirements for
   professional off-road tyres
3. Make editorial corrections where needed throughout the text.