In order to have a Regulation on the retreaded tyres with definitions and provisions structured in the same way of those previously introduced in amendments of “new tyres” Regulations, this amendment:

1. Indicates that for the purpose of this Regulation “tyres” means “pneumatic tyres”, so all the text has been reviewed
2. Introduces a definition of :
   • “retreader” copy based on that “manufacturer” in the tyres regulations
   • Brand name", “Trademark”, “Trade description” and “Commercial name” as defined in the tyre regulations
   • Material manufacturer / material supplier
3. Takes into account the rounding rules (already approved in the other tyre regulations) for the calculation of width and diameter of the tyres
4. Aligns the title and the provisions of the para. 12 related to the names and addresses of Technical Services, Approved Laboratories and administrative Department with their equivalent in the tyres regulations

Proposal to separate requirements for vehicle immobilizers into a new UN Regulation (from UN R116) in order to facilitate the inclusion of anti-theft regulations in UN R0 on whole vehicle type approvals.

Proposal to correct a mistake in Supplement 17 to UN R75 (adopted document WP.29/2017/8). Annex 7, Paragraph 1.2., Footnote 1 should refer to UN R54, not UN R106.

Proposal to add tyre sizes and tyre classification codes common in the United States and standardised by the Tire and Rim Association, but needed under UN Regulation No. 106 in order to permit their type approval in conformity with Regulation EU 167/2013 for imported tyres. The proposal adds kPa marking specifications for use in measurements and tyre testing. The proposal further includes changes to the text and addition of tyre size designations to Annex 5 and Annex 7:

1. Paragraph 2.33.2 deleted since new tables for IF and VF were added to Annex 7
2. Paras 3.2., 3.2.2. and 5.4. modified because “tyres submitted for approval” cannot bear an approval mark until approved and the “only” as it is written can be misunderstood. Para. 3.2.2. was aligned to the wording in other UN Regulations. Reference to para. 3.3 in paragraph 5.4. is deleted because paragraph 3.3 does not refer to specific markings
3. Para 6.1.2. amended to align the wording to the headers in Annex 5 and to correct the reference to the footnote
4. Para 6.2.1. amended to restore the proper references after renumbering resulting from the latest Supplements
5. The amendment of Annex 5, Table 5 adds the value for the overall diameter (D) in column (*) that applies to tyres marked with classification code “I-3”
6. Annex 5, Table 6, Note 1 amended because most of the tyre sizes listed in the table, especially those identified by the “classification code I‐3” (i.e. Traction tread), are currently available in both versions: ‘implement’ to be used on agricultural machinery and ‘IND’ to be used on construction vehicles. The two types of tyres have the same type of size designation and the same dimensions. Therefore some manufacturers identify those tyres with the suffix ‘IND’ rather than with the suffix ‘IMP’ thus applying the variation of load capacity with speed as published in Annex 7 Part E. The reason for this proposal is to avoid a duplication of tables with a new table only replacing the suffix IMP with the suffix IND.
7. The addition of the footnote to Annex 5, Table 7 answers the request by GRRF to introduce appropriate formulae in the Regulation instead of continuously updating Annex 5.
8. References in Annex 7 corrected pursuant to the renumbering following the introduction of three new paragraphs in Supplement 15 approved during the 172nd session of WP.29.
9. Annex 7, Part A amended to conform with Tire and Rim Association specifications for code designated diagonal tyres with speed symbol A8.

Proposal to introduce formulae for tyre sizes in Annex 5, Table B, add sizes in Annex 5, Part II, Tables C and E for old sizes that do not follow the guidelines/formulae applicable for high flotation tyres, amends footnotes in Annex 5, Part II, Table B in order to clarify categories of use, clarify tyre width tolerances, correct paragraph numbering and references, align the text editorially with UN R30 and to make other editorial improvements.

Addendum 1 to the Report of the GRRF on its 86th session

LIGHT TRUCK / C-TYPE HARMONIZED HIGH SPEED TEST: Status and Recommendation for TYRE GTR IWG 18