Pursuant to the addition of a new speed symbol for forestry tyres, this proposal would add a bonus loads column for A6-rated tyres to Annex 7-Part D.

Corrections to the tables concerning “Agricultural implement tyres – Normal section sizes”.

Deletion of a paragraph (concerning UN R90) inadvertently inserted into the justification for the this proposal.

Proposal to amend the tyre dimensional requirements of UN Regulation No. 30.

Proposal to amend the requirements for the load/speed performance test of UN Regulation No. 30.

Proposal to correct the code 19 rim diameter. The value of the rim diameter is calculated by multiplying the rim diameter code by 25.4 and rounding to the nearest integer. For the code 19 rim, the value should be 483 (482.6 rounded).

Proposal to modify the marking requirements to replace PSI with kilopascals (“kPa”). The intent is to harmonize the pressure indication and avoid confusion between UN Regulation No. 54 and US FMVSS 119 or FMVSS 139.

Proposal to amend the tyre dimension requirements. The current rules for calculating the dimensional limits are not consistent among the UN Regulations for tyres and within the Regulations themselves. Hence they lead to uncertainty in the correct calculation. The current proposal aims at unifying the calculation rules to those used in ISO 4000-1 and all major tyre standards, e.g. ETRTO, Tyre & Rim Association (T&RA), Japan Automobile Tyre Manufacturers Association (JATMA).

Proposal to amend the tyre dimension requirements. The current rules for calculating the dimensional limits are not consistent among the UN Regulations for tyres and within the Regulations themselves. Hence they lead to uncertainty in the correct calculation. The current proposal aims at unifying the calculation rules to those used in ISO 4000-1 and all major tyre standards, e.g. ETRTO, Tyre & Rim Association (T&RA), Japan Automobile Tyre Manufacturers Association (JATMA).

Proposal to align UN R106 with international standards (ETRTO, T&RA and ISO 4351-2 table 2) with regard to Improved Flexion (IF) tyres and Very high Flexion (VF) tyres. This proposal also clarifies the application of EC Regulation 167/2013 which refers to UN R106.

Proposal to modify the marking requirements to replace PSI with kilopascals (“kPa”). The intent is to harmonize the pressure indication and avoid confusion between UN Regulation No. 54 and US FMVSS 119 or FMVSS 139. The proposal would also change the measurement units for drum speed from min^-1 to km.h^-1 in alignment with the requirements with other tyre regulations and align the wording in Annex 7, Appendix 1 with the text of the Regulation.

Proposal to add load indexes to the table in the Annex 4 to keep up with the technical evolution of tyres.

Proposal to add new tyre sizes to Annex 5 of UN R54.

Proposal to correct paragraph number references due to the recent renumbering of definitions.

Correction of the paragraph numbering pursuant to the adoption of Supplement 21 and deletion of a redundant note at the end of paragraph 6.1.5.3.3.

Proposal to clarify the minimum heights for markings for tyres with nominal rim diameter codes ≥ 20 and nominal section width ≤ 235 and for tyres with nominal rim diameter codes < 20 and nominal section width > 235. In addition, the proposal corrects the use of uppercase letters to denote dimensions where lowercase letters had been inserted.

Proposal to:
a) Align definitions and contents of paragraphs with the other tyre regulations (UN R30, R54, R117, etc.);
b) Include a definition of “Manufacturer” extracted from the resolution “R.E.3”;
c) Adopt a common definition and use of the terms “Manufacturer’s name”," Brand name", “Trademark”, “Trade description” and “Commercial name” and their links;
d) Clarify which markings shall be moulded on both sidewalls of the tyre; and those which shall be moulded on one sidewall only;
e) Add information in the certificate to clarify the relationship with the certified products;
f) Align definitions with Regulation EU 167/2013 which defines vehicles in category S as “interchangeable towed equipment” and includes tread patterns for ‘implement traction tyres’ that consist of blocks rather than lugs or cleats;
g) Eliminate redundant marking requirements;
h) Clarify the inflation pressure to be used for measurements and tests and related tyre markings;
i) Align the current rules for calculating the dimensional limits in accordance with ISO, all major tyre standards, and as proposed for UN R30, R54, and R75.

Proposal to amend Annex 5 with regard to Improved Flexion (IF) tyres and Very high Flexion (VF) tyres.

Proposal to amend Annex 7 (based on the documents ECE/TRANS/WP.29/GRRF/2015/39 and GRRF-80-16 from Slovakia) and Annex 10. This proposal would:

1. change measurement units for drum speed in Annex 7 from min-1 to km.h-1 to align the requirements with other tyre regulations;
2. correct the wording from “speed category symbol” to “speed symbol” (as defined in para. 2.33);
3. correct the wording from “load capacity index” to “load index” (as defined in para. 2.32);
4. correct a reference to para. 3.2.13. of the Regulation in Annex 7, Appendix 1;
5. correct a boundary value of load index in Annex 7, Appendix 1;
6. delete in paragraph 2.1 in Annex 7, the possibility to use the 2.0 m drum diameter to perform the endurance test.

In Annex 10, the proposal aligns the text with Annex 7 of UN R117, 02 series of amendments, Supplement 5.

Proposal to clarify provisions for the minimum heights for markings for tyres with nominal rim diameter codes ≥ 20 and nominal section width ≤ 235 and for tyres with nominal rim diameter codes < 20 and nominal section width > 235. The proposal also corrects tables and figures for the use of lowercase letter to denote tyre dimension specifications.

Proposal to correct the text where the word “tyres” was inadvertently omitted from Paragraph 2.1.

Proposal for minor editorial corrections to the text.

Proposal for a minor editorial correction to the text. Paragraph 4.8. should read “Annex 2 to this Regulation gives an example of approval marks.” The current text refers to “examples” where there is only one provided.

Regulation No. 106 contains standardized tyre sizes which often need to be updated in line with technical progress. In order to accelerate the update process of the Regulation and limit the number of amendments, it is proposed to establish a new Resolution on standardized sizes and to refer to this Resolution in Annex 5.

Proposal to remove the technical content in Annex 5. This content would be incorporated into a new Resolution on Tyre Sizes as proposed in document GRRF/2016/46.

Proposal to add specifications for tyre sizes 33×11.50R20LT, 35×11.50R17LT, 37×13.50R26LT, 36×15.50R20LT and 40×15.50R26LT.

Regulation No. 106 contains standardized tyre sizes, which often need to be updated, following the technical progress. In order to accelerate the update process of the Regulation and limit the number of amendments, it is proposed to insert in a new Resolution the standardized sizes and to refer to this Resolution in Annex 5. As a temporary solution to assess the effectiveness of such proposal, the Annex 5 of Regulation No. 106 will be kept as it is with no further updates. After a trial period of approximately two years and upon confirmation of effectiveness, the complete Annex 5 of Regulation No. 106 would be transferred to this Resolution on Tyre Sizes.

Regulation No. 106 contains standardized tyre sizes which often need to be updated in line with technological progress. In order to accelerate the update process of the Regulation and limit the number of amendments, it is proposed to insert in a new Resolution the newly standardized sizes and to refer to this Resolution in Annex 5. As a temporary solution to assess the effectiveness of such proposal, the Annex 5 of Regulation No. 106 will be kept as it is with no further updates. After a trial period of approximately two years and upon confirmation of effectiveness, the complete Annex 5 of Regulation No. 106 would be transferred to this Resolution on Tyre Sizes.

Proposal to correct a type in Annex 7- Appendix 2, Part 2, Paragraph 5 where the snow group index should read “1.00”, not “100” as appeared erroneously in the adopted text.

Proposal to:

1. Align definitions and contents of paragraphs with the other tyre regulations (UN R30, R54, R117, etc.);
2. Include a definition of “Manufacturer” extracted from the resolution “R.E.3”;
3. Adopt a common definition and use of the terms “Manufacturer’s name”," Brand name", “Trademark”, “Trade description” and “Commercial name” and their links;
4. Clarify which markings shall be moulded on both sidewalls of the tyre; and those which shall be moulded on one sidewall only;
5. Add information in the certificate to clarify the relationship with the certified products;
6. Align definitions with Regulation EU 167/2013 which defines vehicles in category S as “interchangeable towed equipment” and includes tread patterns for ‘implement traction tyres’ that consist of blocks rather than lugs or cleats;
7. Eliminate redundant marking requirements with the requirement for “@kPa” markings effective from 1 September 2017;
8. Clarify the inflation pressure to be used for measurements and tests and related tyre markings;
9. Align the current rules for calculating the dimensional limits in accordance with ISO, all major tyre standards, and as proposed for UN R30, R54, and R75;

Proposal to update a cross-reference in paragraph 3.4. to read “3.1.2” pursuant to the earlier division of paragraph 3.1 into separate paragraphs 3.1.1. and 3.1.2.

Proposal to

1. correct the references to paragraph 3.17 in paragraph 3.1.12. to refer to 3.20
2. update a cross-reference in paragraph 3.4 to read “3.1.2.” pursuant to the earlier division of paragraph 3.1 into paragraphs 3.1.1. and 3.1.2. (consistent with UN R30)
3. delete the superfluous reference to paragraph 2.19 in paragraph. 4.1.1. (consistent with UN R30)
4. delete the word “existing” from paras. 6.1.1.2. and 6.1.2.2. (consistent with all the other tyre UN Regulations)
5. amend paragraph 6.1.4.2. to take into account the requirements for size designations in Annex 5
6. add a footnote to Annex 5, Part II, Table B to introduce the appropriate formulae in the Regulation (instead of Annex 5)
7. add a size in Annex 5, Part II, Table C for an old size that does not follow the guidelines/formulae applicable for high flotation tyres.

Proposal to

1. amend para 6.1.2. to align the wording to the headers in Annex 5 and to correct the reference to the footnote
2. amend para 6.2.1. to restore corrent references after renumbering made during recent Supplements
3. amend Annex 5, Table 5 to add the value for the Overall diameter (D) in column (*) that applies to tyres marked with classification code “I-3”.
4. amend Annex 5, Table 6, Note 1 to clarify use of the ‘IMP’ and ‘IND’ suffixes for agricultural implements and construction vehicles, respectively.
5. add a footnote to Annex 5, Table 7 is the to introduce the appropriate formulae in the Regulation (instead of via Annex 5)
6. correct cross-references in Annex 7 following the introduction of three new paragraphs in Supplement 15
7. amend Annex 7, Part A to conform with Tire and Rim Association (TRA) specifications for code designated diagonal tyres with speed symbol A8.

Proposal to correct references to paragraphs in Regulations Nos. 30 and 54 which have to be updated pursuant to renumbering in the source regulations.

Proposal to introduce formulae for tyre sizes in Annex 5, Table B, add sizes in Annex 5, Part II, Tables C and E for old sizes that do not follow the guidelines/formulae applicable for high flotation tyres, clarify tyre width tolerances, correct paragraph numbering and references, align the text editorially with UN R30 and to make other editorial improvements,

This document consolidates previous documents GRRF/2017/19 and informal document GRRF-84-17 taking into account the request for addition of tyre sizes and tyre classification codes common in the United States and standardised by the Tire and Rim Association, but needed to be added to UN Regulation No. 106 in order to permit their type approval in order to conform to Regulation EU 167/2013 for tyres to be exported to Europe. It includes addition/modifications of some paragraphs to the main text of the Regulation as well as the addition of some tyre size designations to Annex 5 and Annex 7:

1. ISO 4251-4 replaced by ISO 18805
2. Paragraph 2.33.2 deleted since new tables for IF and VF were added to Annex 7
3. Paras 3.2., 3.2.2. and 5.4. modified because “tyres submitted for approval” cannot bear an approval mark until approved and the “only” as it is written can be misunderstood. Para. 3.2.2. was aligned to the wording in other UN Regulations. Reference to para. 3.3 in paragraph 5.4. is deleted because paragraph 3.3 does not refer to specific markings
4. Para 6.1.2. amended to align the wording to the headers in Annex 5 and to correct the reference to the footnote
5. Para 6.2.1. amended to restore the proper references after renumbering resulting from the latest Supplements
6. The amendment of Annex 5, Table 5 adds the value for the overall diameter (D) in column (*) that applies to tyres marked with classification code “I-3”
7. Annex 5, Table 6, Note 1 amended because most of the tyre sizes listed in the table, especially those identified by the “classification code I‐3” (i.e. Traction tread), are currently available in both versions: ‘implement’ to be used on agricultural machinery and ‘IND’ to be used on construction vehicles. The two types of tyres have the same type of size designation and the same dimensions. Therefore some manufacturers identify those tyres with the suffix ‘IND’ rather than with the suffix ‘IMP’ thus applying the variation of load capacity with speed as published in Annex 7 Part E. The reason for this proposal is to avoid a duplication of tables with a new table only replacing the suffix IMP with the suffix IND.
8. The addition of the footnote to Annex 5, Table 7 answers the request by GRRF to introduce appropriate formulae in the Regulation instead of continuously updating Annex 5.
9. References in Annex 7 corrected pursuant to the renumbering following the introduction of three new paragraphs in Supplement 15 approved during the 172nd session of WP.29.
10. Annex 7, Part A amended to conform with Tire and Rim Association specifications for code designated diagonal tyres with speed symbol A8.

Proposal to add markings for the inflation pressure to be used for measurements and tests.

Consolidated version of UN R54 incorporating the proposed amendments in document GRRF/2018/5.

Consolidated version of UN R106 including ETRTO proposed amendments (see documents GRRF/2018/6 and GRRF/2018/7).

Proposal to update certain Standard Reference Test Tyre (SRTT) denominations, to remove the distinction between the two Class C3 tyres, to clarify the text and remove the reference to tyres “not marked with speed symbol”. This document will be handled by GRB during its 68th session and is referenced under GRVA due to the “conversion” of GRRF.

Proposal to introduce a definition for “Extended Mobility Tyre” based on a new “minimum requirement” performance test procedure with the relevant pictogram to be used to properly distinguish such tyres. This document will be handled by GRB during its 68th session and is referenced under GRVA due to the “conversion” of GRRF.

Proposal to amend UN R64 in line with the introduction of the “extended mobility tyre” into UN R30 (see document GRVA/2018/6). This document will be handled by GRB during its 68th session and is referenced under GRVA due to the “conversion” of GRRF.

Proposal to

1. modify the scope with regard to Category S and R agricultural vehicles,
2. modify the paragraph numbering (and related footnotes) to improve text clarity,
3. to correct an error in Annex 5 Table 7 where “35×16” should read “36×16”,
4. amend Annex 7 Part E to address variations of load-carrying capacity for tyres for construction applications (industrial tractors or skid-steers / mini-loaders) with speed category symbol “D”.

Proposal to introduce measures to reduce variability in noise measurement.