Proposal for the draft regulation on automated lane-keeping systems address the following sections:
2.6. Driver Availability Recognition
2.7. Transition Demand and System Operation during Transition phase
2.8. Information to the driver
2.9. Minimal Risk Manoeuvre
2.10. Emergency Manoeuvre

Matrix of criteria for determining that driver actions signal control over the vehicle and intent to take over from the automated system.

Supporting the proposal for repetition of a limited number of unsuccessful test runs to compensate for external test influences.

Rough draft discussion document for an eventual new UN Regulation.

Preliminary list of safety elements derived from a review of the guidelines and policies issued by Contracting Parties.

Modified list to ensure full alignment with the WP.29 AV Framework Document.

Proposal to improve the proposal submitted by the experts from France and Germany to allow under specified conditions the use of manufacturer logos inside the illuminant surface of a signalling lamp.

The objective of this document is to provide recommendations for the minimum quality of market fuels (i.e. gasoline and diesel) that should be introduced in parallel, and at the same time, with the corresponding emissions standards.They complement the motor vehicle and NRMM pollutant emission standards that a country or a region may be considering to introduce, or to update

Proposal to add a missing footnote concerning the exemptions for heaters located outside the passenger compartment using water as a transfer medium and to clarify that it is not necessary to apply Annex 4 for the heat pump because the heat transfer fluid does not contain polluting air.

Proposal to add a missing footnote and to clarify the application of Annex 4 for heat pumps.

Proposal to add a missing footnote concerning the exemptions for heaters located outside the passenger compartment using water as a transfer medium and to clarify that it is not necessary to apply Annex 4 for the heat pump because the heat transfer fluid does not contain polluting air.

Final refinements developed during the May 2019 GRSP session to the proposal to include booster cushion categories within the scope of the 03 series of amendments to UN R129 (Supplement 3 to the 03 series).

Proposal to clarify the chest Z axis measurement requirement.

Proposal to amend document GRSP/2019/10. The proposal clarifies the way to apply and to understand GTR7 phase 2 static alternative provisions and aligns the area where the gap is measured to actual practice in UN R17 and FMVSS 202a which consider only gaps over a height of 540mm.

Proposal to provide information on the essential measurement information that needs to be recorded in the Type Approval test report

Proposal to improve the repeatability and reproducibility of the assessment of the external dimensions of the ECRS. It does not change any current dimensional requirements relating to the sizes of the body of the ECRS, the support leg or the support leg foot.

The proposal is to amend the ECE/TRANS/WP.29/GRSP/2019/27 and updates ECE/TRANS/WP.29/GRSP/2019/9.

Proposal to clarify that modifications need only be notified to the Type Approval Authority when they have an influence on the performance (compliance with technical requirements of UN R16) and/or the documentation required by the UN Regulation.

Proposal to amend the dynamic option of the draft 10 series of amendments (document GRSP/2018/34). CLEPA proposes that injury risk limits should be based not only on the injury risk curves, but also on technical feasibility given the repeatability and reproducibility limits of the BioRID II test tool. This proposal also corrects the definition of T(end) which is different from T-HRC.

Proposal to amend the dynamic option of the proposal of amendment 1 of UN Global Technical Regulation No. 7 submitted by the Informal Working Group on the Phase 2 of UN GTR No. 7 (document GRSP/2018/27).

Proposal to clarify the application of GTR 7 Phase 2 static alternative provisions and to modify the allowed range of tolerances under the backset retention and energy dissipations test. The proposal would re-introduce certain paragraphs in the 09 series of amendments removed by the draft 10 series (GRSP/2018/34). In addition, the proposals adds the area where the gap measurement procedure by the sphere is appropriate per the Federal Motor Vehicle Safety Standard 202a (i.e. only gaps in the area over 540 mm).

Proposal to amend the static options of the proposal of amendment 1 of UN Global Technical Regulation No. 7 submitted by the Informal Working Group on the Phase 2 of UN GTR No. 7 (document GRSP/2018/27).

Proposal to include booster cushion categories within the scope of the 03 series of amendments to UN R129.

Proposal to amend the static options of the proposal of amendment 1 of UN Global Technical Regulation No. 7 submitted by the Informal Working Group on the Phase 2 of UN GTR No. 7 (document GRSP/2019/5, amended by GRSP-65-24).

Proposal to update a reference with the new European Committee for Standardization (CEN) published EN 71-3:2019 on 10 April 2019 and to delete a cut-and-paste error in Annex 6, Appendix 2 taken from UN R44 referring to ECRS as in the “restricted” category which does not exist in UN R129.

Proposal to update a reference with the new European Committee for Standardization (CEN) published EN 71-3:2019 on 10 April 2019, to delete a cut-and-paste error in Annex 6, Appendix 2 taken from UN R44 referring to ECRS as in the “restricted” category which does not exist in UN R129, and to reconcile and consolidate various references to tolerances for the internal geometry assessment.

Proposal to clarify the requirements for the type approval category of booster seats over 135 cm, to update a reference with the new European Committee for Standardization (CEN) published EN 71-3:2019 on 10 April 2019, to delete a cut-and-paste error in Annex 6, Appendix 2 taken from UN R44 referring to ECRS as in the “restricted” category which does not exist in UN R129, and to reconcile and consolidate various references to tolerances for the internal geometry assessment.