Proposal to insert and amend provisions for Supplement 2 addressing Automated Driving Systems:

• Insert new paragraphs 0, 0.1 to 0.1.3 introducing Supplement 2 to address vehicles of category X and those equipped with an Automated Driving System (ADS)
• Amend paragraphs 1.2 and 1.3 to clarify scope exclusions including manual triggering of AECS while ADSF-2 is active and vehicles of category Y
• Amend footnote 1 regarding armoured vehicle definition
• Insert new paragraphs 2.34, 2.34.1 and 2.34.2 defining ADS feature, ADSF-1 and ADSF-2
• Amend paragraph 26.4.1 to require AECS control accessibility by occupants for ADSF-2 equipped vehicles
• Amend paragraph 26.5.3.1 Table 3 regarding self-test function information
• Amend paragraph 26.6 to specify voice intelligibility for passengers in ADSF-2 equipped vehicles
• Amend paragraph 35.6.1 requiring AECS control accessibility for ADSF-2 equipped vehicles
• Amend paragraph 35.8 to specify voice intelligibility for occupants in ADSF-2 equipped vehicles

Proposal to amend UN R157 for Automated Driving Systems in vehicles of categories X and Y:

• Insert new paragraphs 0.8. to 0.8.2. introducing Supplement 5 to address vehicles of categories X and Y equipped with an Automated Driving System
• Amend para. 1.1. to specify applicability to vehicles of categories N₂, N₃, M₂ and M₃
• Insert new para. 1.3. excluding vehicles of category Y and vehicles of category X without a manual mode intended to be operated on-board the vehicle
• Amend para. 2.5. to define “Ocular reference point”
• Insert new para. 2.20. to define “Safety Concept”
• Amend para. 4.5. regarding affixing of approval marks and its footnote 2
• Amend para. 5.1. to provide for automatic deactivation of BSIS in specified situations and compliance with UN Regulation No. [XXX] for vehicles equipped with an ADS
• Insert new para. 5.2.3. permitting alternative requirements for vehicles of category X with manual mode not using a driver’s seat
• Amend Annex 2 to correct the heading and modify paragraph references
• Amend Annex 4, Appendix, Table 1, footnote 1

Proposal to amend UN R158 based on GRSG-131-36. The supplement renumbers the introduction’s first paragraph to 0.1, describing the regulation’s purpose for rear visibility and detection devices. New paragraphs 0.2–0.2.3 address vehicles of categories X and Y, including exemptions for automated driving systems and manual operation modes. Paragraph 1.4 is amended to exempt category Y vehicles and category X vehicles without on-board manual modes. Amendments modify paragraphs 5.4.1, 12.4, 15.1.3, 15.1.4, 15.2.2, and Annex 9, paragraph 1.3.3.2, addressing safety concepts, rear-view field vision requirements, and vehicle load specifications.

Proposal to amend UN R86 on data storage and event data recorder requirements:

• Insert new para. 0.4. to introduce Supplement 1 to the 02 series of amendments to account for vehicles of categories X and Y and vehicles which can be operated either by a driver or an ADS
• Amend para. 1.1. footnote 1 to add a document reference
• Amend para. 1.3. to exclude VIN, associated vehicle details, location/positioning data, information about any user, date and time of an event from scope
• Amend paras. 2.16., 2.23., 2.29., 2.30., 2.37., 2.38., 2.55., 2.56., 2.58., 2.66., and 2.67. to revise definitions
• Insert new footnote 2
• Amend para. 4.4. to revise the approval mark
• Amend Annex 3 to update arrangements of approval marks
• Renumber footnote 2 to footnote 3 in para. 4.4.1. and amend its text
• Renumber footnote 3 to footnote 4 in para. 11.
• Amend Annex 4 to modify data elements and format requirements

Proposal to insert new paragraphs 0., 0.1. to 0.1.2. introducing Supplement 4 to extend application of UN R163 to vehicles of categories X and Y, and vehicles with manual mode operating above 6 km/h equipped with an Automated Driving System, based on GRSG-131-40. The amendment clarifies that provisions related to driver and manual driving controls shall not apply if absent in the vehicle unless already covered. For vehicles equipped with an Automated Driving System, no special provisions or exemptions apply in any driving mode. Amendments also update footnote references to the Consolidated Resolution on the Construction of Vehicles.

Proposal to insert new paras. 0.1. to 0.1.2. defining scope for vehicles of categories X and Y, amend para. 1.1.1. to specify approval for vehicles of category M₁ and N₁, amend footnote 1 to paras. 0.1., 1.1.1. and 1.1.2., insert new para. 1.1.5. stating the Regulation does not apply to vehicles of category Y and vehicles of category X without manual mode, amend footnote 2 to para. 5.4.1., insert new para. 12.7. defining “Safety Concept”, amend para. 15. to allow alternative requirements for vehicles of category X with manual mode not using a driver’s seat, amend para. 15.2.2. regarding close-proximity vision fields and vehicle load, and amend Annex 9, para. 1.3.3.2. regarding vehicle load.

Proposal to insert new paragraphs 0.11. to 0.11.2. to introduce Supplement 1 to the 01 series of amendments taking into account vehicles of categories X and Y, amend paragraph 1.1. to apply to vehicles of categories M₂, M₃, N₂ and N₃, insert new footnote 1 and new paragraph 1.3., amend paragraphs 2.13. to 2.15. with references to Addendum 6 of Mutual Resolution No. 1 (M.R.1), renumber footnote 1 as footnote 2 in paragraphs 2.13. to 2.15., insert new paragraph 2.31. defining “Safety Concept”, amend paragraph 4.5. and renumber its footnote 2 as footnote 3, insert new paragraph 5.1.3. concerning vehicles of category X with manual mode, and amend Annex 3.

Proposal to insert new para. 0.5. to introduce Supplement 1 to take vehicles of categories X and Y into account and vehicles which can be operated either by a driver or an ADS, amend para. 1.1. footnote * to reference ECE/TRANS/WP.29/78/Rev.8, amend para. 1.3. to exclude Vehicle Identification Number, associated vehicle details, location/positioning data, information about any user, and date and time of an event from the scope, and amend para. 5.4. to specify survivability requirements for event data recorders including mounting position and mechanical shock resistance under Option 1 or impact severity demonstration under Option 2 with reference to UN Regulation Nos. 94, 95, and 137.

Proposal to amend UN R83 specifications for emission testing:

• Amend para. 1.1.1., Footnote 1, to update the reference to the Consolidated Resolution on the Construction of Vehicles (R.E.3.) document ECE/TRANS/WP.29/78/Rev.8
• Amend para. 24.3.1. to specify that emission of visible pollutants shall be measured by two methods in Annexes 4 and 5, with special procedures for hybrid electric vehicles or vehicles equipped with an ADS detailed in the service manual
• Amend Annex 5, para. 2.4. to require the gear be in neutral and the drive between engine and gear-box engaged when the test is carried out on a vehicle
• Amend Annex 5, para. 2.5. to detail engine speed demand procedures during testing

Proposal to revise definitions for malfunction indication, reference mass, unladen mass, and vehicle user; add provisions for vehicles equipped with an Automated Driving System; establish documentation requirements for vehicle user warning and inducement systems; update testing procedures for in-service conformity and OBD connector location; and specify activation and deactivation mechanisms for vehicle user warning and inducement systems across multiple annexes, with references to WP.29/1045.

Proposal to amend para. 1.1., Footnote 1 to update the reference to the Consolidated Resolution on the Construction of Vehicles (R.E.3.) document ECE/TRANS/WP.29/78/Rev.8, para. 2, and amend para. 4.5.1., Footnote 2 to update the reference to Annex 3 of the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.8.

Proposal to amend Paragraph 1.4., Footnote 1 to update the reference to the Consolidated Resolution on the Construction of Vehicles; insert new paragraphs 2.10. and 2.11. defining “ADS user” and “Vehicle user”; amend Paragraph 5.5.2., Footnote 4 to update the reference to Annex 3 of the Consolidated Resolution; and amend paragraphs 6.1.2.4.1.6.1. and 6.2.2.4.1.6.1. to specify that engine starting-up on petrol and switching to LPG or CNG after a predetermined period cannot be changed by the vehicle user.

Proposal to amend paragraph 1.1., footnote 1 to update the reference to the Consolidated Resolution on the Construction of Vehicles (R.E.3.); amend paragraph 4.4.1. to establish requirements for a dual-fuel operating mode indicator including visual and audio signals, with restrictions on indicator design and safety alert priority; amend paragraph 4.4.1.1. to require warnings when engine operation is forced to diesel mode and signals to an ADS feature; and amend paragraph 7.1. to specify OBD system requirements for diesel and dual-fuel operation modes, including malfunction detection and driver notification procedures.

Proposal to amend UN R101:

• Enable approval of vehicles equipped with Automated Driving Systems
• Introduce provisions relating to Manipulation Devices and Strategies previously in UN R83 09 series
• Clarify laboratory test requirements for pure electric range ratio at low temperature for Pure Electric Vehicles
• Allow use of actual tyre rolling resistance values in Levels 1A and 2
• Align the Regulation with current regional status and state-of-the-art

Proposal to amend UN R86 on various provisions related to vehicle scope, mass definitions, approval references, and test requirements:

• Amend paras. 1.1. and 1.2. to modify the scope for Level 1A and Level 1B
• Insert Footnote 1 to para. 1.
• Amend para. 3.3. to revise the heading
• Amend para. 3.3.3. to redefine “Mass in running order” and clarify driver mass inclusion for vehicles of categories X and Y
• Amend Note a of Figure 3 to align the definition of mass and driver mass treatment
• Renumber Footnote 1 to Footnote 2 in para. 5.4.1. and amend its content to reference the 1958 Agreement distinguishing numbers
• Amend para. 8.3.1. to expand vehicle condition requirements including selectable modes, battery charge mode, ADS features, aerodynamics modifications, test mass composition, driving behaviour verification, and emissions monitoring parameters
• Insert new para. 9.3.5. and new para. 9.3.5.1. to establish special provisions for vehicles equipped with an ADS
• Amend Annex 1 Part 1 to add approval number references to UN Regulation No. 154 and level of approval designation
• Amend Annex 1 Part 2 to add level of approval designation
• Amend para. 12.10. of Annex 1 Part 2 to expand the scope of devices or systems with user-selectable modes to include electric energy consumption
• Amend the explanatory note (h) of Annex 1
• Amend row 21 of Table A4/1 in Annex 4 to modify acceleration demand parameters.

Proposal to enable the approval of vehicles equipped with an Automated Driving System and to optimize the measurement accuracy requirements for chassis dynamometer equipment and the measurement acquisition of the intake manifold pressure in system power testing for high-performance vehicles and makes editorial corrections.

Proposal to amend UN R86 to address Automated Driving Systems:

• Insert new paragraphs 0, 0.1 to 0.1.2 introducing Supplement 3 to address vehicles of categories X and Y and conventional vehicles equipped with an Automated Driving System (ADS)
• Amend paragraph 1.1 footnote 1 to reference ECE/TRANS/WP.29/78/Rev.8
• Amend paragraph 1.3 subparagraph (a) to include control by an ADS
• Insert new paragraph 2.9.4 defining “Presence of an ADS”
• Amend paragraph 2.12 to expand immunity related functions to include ADS-related functions and functions related to charging mode when coupled to the power grid
• Delete paragraphs 2.26 and 2.27
• Renumber paragraphs 2.28 to 2.33 as 2.26 to 2.31
• Insert new paragraph 2.32 defining “ADS test configuration”
• Renumber paragraph 2.34 as 2.33
• Insert new paragraph 3.1.9 requiring specification of seating position if driver’s seat is not the front seat nearest to opposing traffic
• Insert new paragraph 6.11 and subparagraphs 6.11.1 to 6.11.3 establishing special requirements for ADS-equipped vehicles including alternative test methods and ESA immunity testing
• Amend paragraph 9.3.2 to reference ADS degradation in conformity verification
• Amend Appendix 8 paragraph 2 figures 3, 4, 5 and paragraph 3 figure 6 to correct charging notation from “>” to “<” and adjust time from 60 to 20 seconds
• Add new items 74 and 75 to Annex 2A addressing ADS presence and description
• Insert new paragraph 7 to Annex 3A Appendix and renumber former paragraph 7 as 8
• Amend Annex 4 paragraph 2.1.2 to reference ADS capability to switch equipment
• Amend Annex 5 paragraph 2.3 to reference ADS
• Amend Annex 6 paragraph 2.1.1.2 to establish “50 km/h mode”, “Brake mode” and “Active ADS Mode” test conditions with corresponding failure criteria including ADS operational state requirements
• Amend paragraph 2.1.1.3 to reference ADS
• Amend paragraph 2.1.1.4 to reference ADS features control
• Delete paragraph 2.1.1.5
• Amend paragraph 2.1.2 to permit manufacturer evidence for systems not operating under specified conditions
• Amend paragraph 2.2.1.3 to reference ADS for equipment switched OFF

Proposal to amend para. 6.5.4. to permit an automated driving system to control the cleaning device while active and to require the cleaning device to operate through at least one cleaning period when headlamps are switched on and windscreen washers are operated, except for vehicles of categories X and Y, and insert a new footnote 4 defining automated driving system as in ECE/TRANS/WP.29/78/Rev.8, para. 2.

Proposal to add provisions for Automated Driving Systems (ADS) in vehicle lighting and light-signalling functions, insert definitions for ADS-related terms and direction indicator projection, amend direction-indicator lamp definition to reference UN Regulations 97, 116, 162, and 163, add direction indicator projector definition, amend switch ON/OFF and activate/deactivate definitions to include ADS operation, insert definitions for basic elements and direction indicator projection, add requirements for direction indicator projection patterns in approval documentation, add driver seat position specification requirement, amend headlamp discomfort and ADS performance requirements across multiple paragraphs, insert main-beam control requirements for active ADS features, amend dipped-beam and front fog lamp provisions to account for ADS, add automatic alignment and luminous intensity adaptation provisions, amend side-marker lamp operation to permit ADS control, insert direction-indicator lamp flash requirements for ADS operation, add hazard warning signal control by ADS, amend interior lighting provisions, amend front-facing lighting unit height requirements for ADS-equipped vehicles without windscreens, insert ADS control requirements for cornering lamps and reversing lamps, amend Adaptive Front-lighting System (AFS) provisions to permit ADS control, insert new paragraph 6.28. establishing comprehensive direction indicator projection requirements including presence (optional), number, arrangement, position, projection area boundaries, orientation, electrical connections (flash synchronisation with direction-indicator lamps), tell-tale (optional), visual testing requirements, pattern restrictions, and operational restrictions based on vehicle speed and gear engagement, add Communication Form items for direction indicator projection luminous intensity and projector compliance, add item for ADS presence indication, add item for driver seat location specification, amend Annex 5 loading conditions to establish “seating position 1” terminology for the front seat nearest opposing traffic with provisions for ADS-equipped vehicles of categories X and Y, and insert new Annex 18 specifying the chevron as the sole basic element in amber for direction indicator projection patterns.

Proposal to insert new paras. 0., 0.1. to 0.1.2. to introduce Supplement 3 to the 01 series of amendments to take into account vehicles of categories X and Y and vehicles with a manual mode operating at speeds above 6 km/h equipped with an Automated Driving System, amend footnote 1 in para. 1. to provide updated reference to the Consolidated Resolution on the Construction of Vehicles, and amend footnote 2 in para. 5.3.4.1. to provide updated reference to the Consolidated Resolution on the Construction of Vehicles.

Proposal to amend UN Regulation No. 167:

• Amend para. 0.10. through 0.10.2. to introduce scope for vehicles of categories X and Y
• Amend para. 1.1. to add footnote 1 defining vehicle categories
• Insert new para. 1.3. excluding category Y and category X vehicles without manual on-board operation
• Amend paras. 2.13. to 2.15. to reference Addendum 6 of Mutual Resolution No. 1 (M.R.1) and renumber footnotes
• Insert new para. 2.31. defining “Safety Concept”
• Amend para. 4.5. to revise approval mark requirements and renumber footnotes
• Insert new para. 5.1.3. permitting alternative requirements for category X vehicles with manual on-board operation
• Amend Annex 3 to revise approval mark arrangements