Proposal to amend Amendment 2 to UN GTR No. 22: Modify para. 5.2. to define virtual distance calculation and add requirements for reporting virtual distance by vehicles with V2X functionality or Category 2 vehicles used for non-traction purposes, add new para. 5.2.1. specifying virtual distance determination, add para. 6.1.3. defining Part C family criteria for virtual distance verification, add para. 6.5. establishing Part C verification procedure for reported virtual distance with test conditions including environmental temperature 23°C ± 5°C, initial battery SOC according to normal charging procedure, discharge testing at highest available power, test duration of 50 km virtual distance or 2 hours, and pass/fail criteria requiring reported virtual distance not more than 5 per cent higher than measured virtual distance, add para. 6.5.2.1. with statistical decision chart for Part C pass/fail determination based on cumulative sample size and failed result counts, revise para. 6.1.4. to add family identifier format for virtual distance families, add para. 52.a. through 52.e. in the Statement of Technical Rationale documenting Phase 3 developments including family criteria for Part C verification, boundary conditions for virtual distance verification test with environmental temperature requirements and discharge test options based on kilometres or hours, OVC-HEV UBE correction in Annex 3, and additional regional regulation requirements in Annex 2, and add flow chart Figure 3 for Part C verification process.
The Equitable Occupant Protection Informal Working Group to GRSP pursues equitable and enhanced protection of a diverse population through robust regulatory solutions addressing rear-end and frontal impacts. Strategic goals include reducing injury risk for restraint systems, assessing currently not considered injury types with high frequency and risk of Permanent Musculoskeletal Impairment, and avoiding bias in protection. The group established task forces on rear impact seat assessment focusing on soft tissue neck injuries, virtual crash testing, frontal impact and restraint system requirements, and extension of assessment towards currently not considered injury types. Upcoming workshops are scheduled for June online, September in Munich, and November in Tokyo. Next steps include prioritization and categorization of identified topics into short-term, mid-term, and long-term timeframes within respective task forces.
Based on LS-1691, this document defines specifications for HB3 LED light sources. LED light sources shall not exceed the specified envelope, function in either voltage polarity, and be rotated in the measuring holder until the reference lug contacts the holder plane. Essential electrical and photometric characteristics include rated values at 12V and 13.2V, with minimum luminous flux of 2000 lm and cap temperature limits. Luminous flux measured at elevated ambient air temperature shall be at least 75% of objective luminous flux. Screen projection requirements specify box system proportions for light emitting areas and contrast limits. Normalized luminous intensity distribution shall comply with specified limits in defined C-planes when measured at test voltage.
This document defines category HIR2 LED light source specifications. The LED light source shall not exceed the envelope indicated in Figure 2, be concentric to the reference axis, and function in either voltage polarity. Essential characteristics include rated values at 12 volts DC of 26 watts power and 2000 lm minimum luminous flux. Cap temperature shall not exceed 63°C at test voltage or 100°C at elevated ambient air temperature. Luminous flux measured at elevated ambient air temperature shall be at least 75% of objective luminous flux. Light emitted shall be white. The contrast proportion of luminous flux shall be 100 minimum. Normalized luminous intensity distribution shall comply with specified limits in C-planes.
This document specifies requirements for category H10 LED light sources with PY20d caps. The light source shall not exceed the outlined envelope and shall function in either voltage polarity. Essential characteristics include rated values of 12 volts and 21 watts, with luminous flux of 1500 lm minimum at test voltage. The luminous flux measured at elevated ambient air temperature shall be at least 75% of objective luminous flux. Screen projection requirements define light-emitting area positioning using box systems. Normalized luminous intensity distribution requirements are specified in C-planes with defined test points and minimum/maximum intensity values in cd/klm.
This document defines essential dimensions, electrical characteristics, and photometrical requirements for LED light source category H9. The LED light source shall not exceed the specified envelope and shall function in either voltage polarity. Rated values include 26 watts at 12 volts and 26 watts minimum at 13.2 volts, with minimum luminous flux of 2000 lm and cap temperature not exceeding 100°C. The luminous flux measured at elevated ambient air temperature shall be at least 75% of objective luminous flux. The document specifies screen projection requirements, contrast requirements, and normalized luminous intensity distribution requirements across defined C-planes and test points.
Revision of TFSR-26-03 addresses H9 LEDr flux considerations and dual-voltage specification. The document proposes applying a single specification for H9 LEDr: 1875 lm ±10% @13.2V, representing a compromise between high-beam and low-beam applications. This luminous flux level is not critical, as high-beam measurements with H9 filament bulbs exceed legal minimums by more than 10%, and low-beam safety margins remain acceptable with limited flux increases. Additionally, a black-top limit of 50 cd/klm at control point zero is proposed for bulbs without black-top specification, and LEA sub-zone specifications (B1, B2, B3) for high-beam categories should be optimized to support beam performance.
Proposal to revise the terms of reference and rules of procedures for the Informal Working Group on Advanced Emergency Braking Systems. The IWG shall review current regulatory actions and data on Automated Emergency Braking Systems and provide recommendations on future regulatory actions including revisions to UN Regulation No. 152. The IWG shall examine current AEBS regulations worldwide, assess accident situations for passenger vehicles, draft state-of-the-art performance requirements for collision scenarios involving pedestrians at night, investigate regulatory improvements to performance requirements, and investigate feasibility to include updated requirements to avoid false activation of AEBS for light vehicles. The IWG shall deliver complete regulatory text for AEBS for passenger vehicle requirements as revision of UN Regulation No. 152 for the September 2028 session of GRVA at the latest.
No documents available.