Proposal to revise the weight threshold of M₃ vehicle category from 7.5 tonnes to 12 tonnes, split N-type trucks into three categories with light-duty trucks below 5 tonnes, medium-duty trucks above 5 tonnes and N₃ below 18 tonnes, and heavy-duty trucks above 18 tonnes, adjust year and mileage limits for N₂, N₃ medium-duty trucks to 8 years or 500,000 km, and establish energy throughput requirements: M₂ 120,000 kWh, M₃≤12t 300,000 kWh, M₃>12t 500,000 kWh, N₂≤5t 200,000 kWh, N₂>5t, N₃≤18t 400,000 kWh, N₃>18t 1,200,000 kWh.

This document proposes establishing a unified global testing method for determining system power and torque of heavy-duty hybrid electric vehicles (HD-HEV) and heavy-duty plug-in electric vehicles (HD-PEV). The proposal addresses the lack of standardized test methods by recommending hub-coupled dynamometer testing for vehicles with central drive systems and chassis dynamometer testing for other configurations. Testing should measure 30-minute continuous maximum power and torque under thermal equilibrium conditions. The document includes technical data from battery energy distribution analysis and recommends China lead formulation of this standard using chassis dynamometer verification.

Under GTR 25, a feasibility assessment proposes introducing a 5-year mid-term performance requirement threshold together with corresponding mileage and energy-throughput limits as an intermediate verification checkpoint for battery degradation. Based on analysis of State-of-Health data from vehicles with 5-year life and mileage ranging from 250,000 km to 350,000 km, the MPR value is set at 75%, which can cover 98% battery-durability performance. Specific mileage and energy-throughput limits are established for vehicle categories M₂, M₃, N₂, and N₃.

GTR 25 establishes alternative test and verification methods for heavy-duty vehicle energy consumption. China released test method GB/T 18386.2-2022 based on chassis dynamometers using continuous cycle and shortened methods. Test conditions include temperature of 25°C ± 5°C, initial battery SOC of 20%, and pre-conditioning soak and charge for minimum 6 hours and maximum 36 hours. The torque meter method measures road load without disabling regenerative braking, achieving resistance matching within 5% error. Test verification includes vehicle selection across mileage groups 0, 200,000, 400,000, and 600,000 km, with on-board data collection and sensor accuracy consistency analysis post-durability.

China introduces an assessment of low State of Charge Energy requirements for M-type vehicles using data from city buses and coaches. At low SOCE levels, available energy is reduced, requiring increased initial battery energy capacity to meet customer driving range expectations, leading to higher purchase costs and vehicle weight. China provides reasons supporting SOCE performance targets at an 8-year timeframe, including significant differences in vehicle types, operating conditions, business models, and battery specifications that vary by vehicle type, making uniform standards inefficient.

The document addresses Part C verification of virtual distance for heavy-duty vehicle batteries. OICA reports pilot phase results from Volvo Group and Daimler Truck AG testing measurement procedures and accuracy under driving and stationary conditions. Key findings show measurement accuracy decreases significantly at lower power levels, with deviations of 0.3% to 4% at higher power. PTO system characteristics influence accuracy; internal PTOs performed better than bodybuilder-installed units. The document identifies challenges including formula correction needs, PTO family concept complexity, and proposes further testing before finalizing Part C requirements.

Japan proposes to add a specific requirement for vehicle speed measurement frequency of 20 Hz in Table A3/1 of Annex 3, consistent with UN R154; revise para. 2.4 to clarify that both constant and transient cycles test methods are permitted; delete redundant text from para. 2.4.1 regarding test cycle requirements; and delete from para. 5.1 the requirement that resolution and method for SOCE availability be determined in agreement with authorities, as these are already specified.

Proposal to:

• Amend para. 2.1.(a) to include fuel cell electric vehicles that have more than one propulsion energy converter,
• Add fuel cell electric vehicle preparation requirements to para. 6.3. requiring run-in in accordance with manufacturers recommendations and at least 300 km of fuel cell run-in with hydrogen refueled in accordance with manufacturers recommendations,
• Amend para. 6.5. to include FCEVs in initial REESS charge requirements,
• Amend para. 6.8.1. to include fuel cell temperature in operational metrics to be monitored and recorded throughout the test,
• Retitle para. 2.6. as Fuel cell architectures, and add paras. 2.6.1., 2.6.2., and 2.6.3. specifying power determination reference points and test procedures for fuel cell architectures.

Proposal to improve efficiency of test methods by adding a reference to SAE J1349 or applicable local regulations, in addition to UN R85 and ISO 1585, to para. 6.1.2. and para. 6.1.2.1., and delete the requirement for Current integration measurement from para. 5.2.1. The additions provide consistency throughout the regulation and clarify that test results obtained in accordance with applicable local regulations are considered valid. The deletion removes an inconsistency whereby only Current integration measurement specifies a frequency of 20 Hz, while other items specify at least 10 Hz, and eliminates inapplicable wording carried over from UN R154.

The agenda addresses UN GTR 22, UN GTR 21, and UN GTR 25, with discussions on fuel cell vehicle proposals, open items, verification results, alternative test methods, and battery replacement provisions. A reminder notes that UN GTR 25 amendment 2 must be submitted to GRPE-96 by December 2026.

The 98th EVE IWG session held virtually on July 15, 2026, adopted the agenda and discussed Phase 4 priorities for UN GTR 22, including Minimum Performance Requirements, State of Certified Range, conditioning cycles, and mutual recognition. Japan proposed sharing Part C verification results with all Contracting Parties. The IWG reviewed UN GTR 21 and UN GTR 25 status, covering MPRs, energy throughput, virtual distance verification, and battery replacement provisions. OICA will present their MPR position at EVE 100 and share Part C verification results at EVE 99. Japan will consult on hosting 2027 meetings targeting the week of February 15th.

Proposal to revise provisions and formulas in GTR 22 Annex 3, paras. 2.1.2. and 3.1.2., UN R154-04 Annex C1, Appendix 2, paras. 2.1.2. and 3.1.2., and UN R83-09 Appendix 5, para. 3.1.2. to make UBE_certified values positive and select the maximum absolute value. The document EVE-63-11e addresses concerns that when the interpolation method is applied under GTR No. 15 / UN R154, UBE_certified values become negative, contrary to regulatory intent. Revisions ensure UBE_certified is determined by selecting the maximum absolute value amongst vehicle H, vehicle L, and vehicle M where applicable.