For light sources with integrated electronics an “Electronic light source control gear” comprises components between the supply and the light emitting elements. The definition was derived from IEC and CIE, where a light source is the light emitting element. Provisions for “Electronic light source control gear” are normally used in installation and device regulations, but create confusion in relation to light sources with integrated electronics. Therefore, it is proposed to tune this term to the use in installation and device regulations and no longer specifically mention integration (or not) in the light source; “Electronic light source control gear” is not defined in R.E.5., but is part of the light source definition. The proposal also delete the term “igniter” because it is not used in the regulation.

Proposal from the SLR informal group to introduce into the 06 and 07 series of amendments to UN R48 references to the headlamp Classes in the 01 series of amendments to UN R149.

Proposal to permit the installation of manoeuvring lamps on trailers.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to add a reference to the installation parameters of the licence plate illumination lamps determined during their type approval process. Every type-approved device or pair of devices have their own geometrical position in relation to the rear registration plate which is determined based on the illumination levels, maximum gradient value, angles of visibility and light incidence angle. This proposal would introduce a reference to these parameters in UN R48.

Proposal to allow the projection of driver assistance symbols on the road ahead of the vehicle as part of the Adaptive Driving Beam (ADB).

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

For light sources with integrated electronics an “Electronic light source control gear” comprises components between the supply and the light emitting elements. The definition was derived from IEC and CIE, where a light source is the light emitting element. Provisions for “Electronic light source control gear” are normally used in installation and device regulations, but create confusion in relation to light sources with integrated electronics. Therefore, it is proposed to tune this term to the use in installation and device regulations and no longer specifically mention integration (or not) in the light source; “Electronic light source control gear” is not defined in R.E.5., but is part of the light source definition. The proposal also delete the term “igniter” because it is not used in the regulation.

Proposal from the SLR informal group to introduce into the 06 and 07 series of amendments to UN R48 references to the headlamp Classes in the 01 series of amendments to UN R149.

Proposal to permit the installation of manoeuvring lamps on trailers.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to clarify the height requirements for the installation of the dipped-beam headlamp, reversing lamp and rear fog lamp for vehicles of category G (designed for off-road use).

Proposal to allow the projection of driver assistance symbols on the road ahead of the vehicle as part of the Adaptive Driving Beam (ADB).

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

For light sources with integrated electronics an “Electronic light source control gear” comprises components between the supply and the light emitting elements. The definition was derived from IEC and CIE, where a light source is the light emitting element. Provisions for “Electronic light source control gear” are normally used in installation and device regulations, but create confusion in relation to light sources with integrated electronics. Therefore, it is proposed to tune this term to the use in installation and device regulations and no longer specifically mention integration (or not) in the light source; “Electronic light source control gear” is not defined in R.E.5., but is part of the light source definition. The proposal also delete the term “igniter” because it is not used in the regulation.

Proposal from the SLR informal group to introduce into the 06 and 07 series of amendments to UN R48 references to the headlamp Classes in the 01 series of amendments to UN R149.

Proposal to permit the installation of manoeuvring lamps on trailers.

For a more efficient discussion during the 83rd session of GRE the experts from the International Organization of Motor Vehicle Manufacturers merged documents GRE/2020/08-Rev.1 (SLR) and GRE/2020/23 into one document.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to allow the projection of driver assistance symbols on the road ahead of the vehicle as part of the Adaptive Driving Beam (ADB).

Proposal to allow the projection of driver assistance symbols on the road ahead of the vehicle as part of the Adaptive Driving Beam (ADB).

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

For light sources with integrated electronics an “Electronic light source control gear” comprises components between the supply and the light emitting elements. The definition was derived from IEC and CIE, where a light source is the light emitting element. Provisions for “Electronic light source control gear” are normally used in installation and device regulations, but create confusion in relation to light sources with integrated electronics. Therefore, it is proposed to tune this term to the use in installation and device regulations and no longer specifically mention integration (or not) in the light source; “Electronic light source control gear” is not defined in R.E.5., but is part of the light source definition. The proposal also delete the term “igniter” because it is not used in the regulation.

For light sources with integrated electronics an “Electronic light source control gear” comprises components between the supply and the light emitting elements. The definition was derived from IEC and CIE, where a light source is the light emitting element. Provisions for “Electronic light source control gear” are normally used in installation and device regulations, but create confusion in relation to light sources with integrated electronics. Therefore, it is proposed to tune this term to the use in installation and device regulations and no longer specifically mention integration (or not) in the light source; “Electronic light source control gear” is not defined in R.E.5., but is part of the light source definition. The proposal also delete the term “igniter” because it is not used in the regulation.

Proposal from the SLR informal group to introduce into the 06 and 07 series of amendments to UN R48 references to the headlamp Classes in the 01 series of amendments to UN R149.

Proposal to permit the installation of manoeuvring lamps on trailers.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to allow the projection of driver assistance symbols on the road ahead of the vehicle as part of the Adaptive Driving Beam (ADB).

Proposal to allow the use of manufacturer logos in the internal structure of optical components and/or in the outer lens within the apparent surface of a signalling lamp.

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

This proposal base on document GRE/2019/20 and is an alternative to document GRE/2019/14.
Currently, UN Regulation No. 48 does not allow the manual switching off all lighting devices under all circumstances. This feature is necessary for armed services and forces responsible for maintaining public order and is requested by them. It is limited only to vehicles intended for use by the armed services and forces responsible for maintaining public order. This proposal aims to reduce disadvantages and can increase safety.

For light sources with integrated electronics an “Electronic light source control gear” comprises components between the supply and the light emitting elements. The definition was derived from IEC and CIE, where a light source is the light emitting element. Provisions for “Electronic light source control gear” are normally used in installation and device regulations, but create confusion in relation to light sources with integrated electronics. Therefore, it is proposed to tune this term to the use in installation and device regulations and no longer specifically mention integration (or not) in the light source; “Electronic light source control gear” is not defined in R.E.5., but is part of the light source definition. The proposal also delete the term “igniter” because it is not used in the regulation.

Proposal from the SLR informal group to introduce into the 06 and 07 series of amendments to UN R48 references to the headlamp Classes in the 01 series of amendments to UN R149.

Proposal to permit the installation of manoeuvring lamps on trailers.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to allow the manual switching off all lighting devices in all circumstances for vehicles intended for use by the armed services and forces responsible for maintaining public order.

Proposal to allow the projection of driver assistance symbols on the road ahead of the vehicle as part of the Adaptive Driving Beam (ADB).

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

Proposal from the SLR informal group to introduce into the 06 and 07 series of amendments to UN R48 references to the headlamp Classes in the 01 series of amendments to UN R149.

Proposal to permit the installation of manoeuvring lamps on trailers.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to allow the projection of driver assistance symbols on the road ahead of the vehicle as part of the Adaptive Driving Beam (ADB).

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

For light sources with integrated electronics an “Electronic light source control gear” comprises components between the supply and the light emitting elements. The definition was derived from IEC and CIE, where a light source is the light emitting element. Provisions for “Electronic light source control gear” are normally used in installation and device regulations, but create confusion in relation to light sources with integrated electronics. Therefore, it is proposed to tune this term to the use in installation and device regulations and no longer specifically mention integration (or not) in the light source; “Electronic light source control gear” is not defined in R.E.5., but is part of the light source definition. The proposal also delete the term “igniter” because it is not used in the regulation.

For light sources with integrated electronics an “Electronic light source control gear” comprises components between the supply and the light emitting elements. The definition was derived from IEC and CIE, where a light source is the light emitting element. Provisions for “Electronic light source control gear” are normally used in installation and device regulations, but create confusion in relation to light sources with integrated electronics. Therefore, it is proposed to tune this term to the use in installation and device regulations and no longer specifically mention integration (or not) in the light source; “Electronic light source control gear” is not defined in R.E.5., but is part of the light source definition. The proposal also delete the term “igniter” because it is not used in the regulation.

Proposal from the SLR informal group to introduce into the 06 and 07 series of amendments to UN R48 references to the headlamp Classes in the 01 series of amendments to UN R149.

Proposal to permit the installation of manoeuvring lamps on trailers.

Proposal to permit the installation of manoeuvring lamps on trailers.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to address semitrailers where the required distance of the foremost side-marker lamp of 3 m from the front cannot be achieved.

Proposal to allow the projection of driver assistance symbols on the road ahead of the vehicle as part of the Adaptive Driving Beam (ADB).

Proposal from the SLR informal group to correct paragraph numbering and to re-introduce omissions that were deleted by mistake by previous amendments.

Proposal from the SLR informal group to introduce into the 03, 04, and 05 series of amendments to UN R48 references to the headlamp Classes in the 01 series of amendments to UN R149.

Proposal to introduce new requirements for headlamp levelling, in particular on the vertical inclination in relation to the dipped-beam headlamp mounting height.