Proposal to explicitly allow other technical measurement solutions of the tyre overall width by removing the words “by calliper”, add the definition of “special tyre”, clarify the definition of “snow tyre”, to enable the case of a “special tyre” fulfilling the definition of a “snow” tyre, clarify application of the suffix “M/C”, and make editorial corrections and clarifications.
Proposal to address the following:
1. “Special use” tyres with nominal rim diameters larger than those listed in the present table (rim diameters up to 42, section widths up to 750 mm and overall diameters over 2 meters) and with speed symbols F and above have been announced in the European market as original equipment of N3G “special purpose vehicles” (i.e., special high speed self-propelled vehicles for agricultural and forestry use, like wood choppers).
2. Existing multi-purpose tyres (MPT) (classified as “special use tyres” as per paragraphs 2.5.3. and 3.1.13.), already type approved since years, have a tread pattern with lugs or cleats in addition to those with blocks, as evidenced by the attached slide showing some examples. It is proposed to amend paragraph 6.3.1. by clarifying that lugs and cleats are possible shapes of the mentioned blocks.
3. Testing tyres with very large overall diameters, sometimes over 2 m, on a test drum with a diameter of 1.70 m ± 1 % would be unpracticable. For practical reasons most of those
tyres are regularly tested on drums with a diameter of 3 m or even larger. The proposal carries equivalence provisions from UN R106 to justify the equivalence of the test method as required by Annex 7 in point 4 “Equivalent test methods" and clarifies based on UN R117 the formula already used indirectly.
4. Some commercial vehicles are often used in the market at a reduced speed of 70 km/h with a load-capacity of the tyres increased as per load/speed combination defined in the table of Annex 8. The proposal would allow use of the speed category symbol E (but restrict it to “additional service description”) to provide this information.
5. Considering that 32 km/h is already a floor value for the test-drum speed for diagonal tyres, ETRTO proposes not to apply to E speed category symbol tyres the linear decrease of
the test-drum speed in function of the decrease of the speed category symbol by keeping, for safety reasons, the same test-drum speed as for F speed category symbol tyres, i.e., 32 km/h).
6. In the case of additional service descriptions mentioned in paragraph 184.108.40.206., it is proposed not to perform the additional load/speed test because the load-capacity approximates with a negligeable difference the reduction or the increase in percentage of the nominal load/speed combination applicable to the nominal speed category symbol (see Annex 8).
7. Type approval applications for radial tyres with load capacity index greater or equal to 122 and without the additional marking “LT”, or “C” have been done in the past for the speed category symbol N for which the load/speed endurance test procedure is not described in Annex 7, Appendix 1. To type approve such tyres the test speed was separately defined by the different involved Type Approval Authorities. In order to harmonize the test procedure to be used for the type approval of such tyres, it is proposed to amend the Annex 7, Appendix 1 by introducing testing conditions in line with the rule applied for defining the test speed of radial tyres with load capacity index greater or equal to 122 (i.e. starting from 32 km/h set for F speed category symbol, the test speed is increased by 8 km/h respect to the one set for the previous speed category symbol).
8. The definition of “snow tyre” is amended to clarify that “snow tyres” are not only suitable for the use in snow conditions but also on mud and by replacing the term “maintain vehicle motion” (i.e. keeping the vehicle speed and direction of movement constant) by a more general concept of “controlling vehicle motion” (i.e. also being able to change the vehicle speed and direction of movement as intended).
9. It is proposed to explicitly allow other technical measurement solutions of the tyre overall width by removing the words “by caliper” which fix a technical limitation. The removal of this technical limitation would be advisable following the principle of not stopping the technical innovations.
10. Editorial corrections are introduced to ensure that the terms “load-capacity” and “speed category symbol” are used consistently throughout the text and to remove some typing mistakes present in the current text.
JRC replies to the questions received from the 24th EVS informal group session on the presentation “Gas emissions from thermal runaway and propagation of Li-ion battery cells in short stack and module experiments”.
Proposal to correct some references, which need to be updated as a consequence of document WP.29/2020/70, adopted at the June 2020 WP.29 session, notably
Proposal to amend the extended mobility tyre (EMT) symbol following the detection of dimensional inconsistencies within the International Organization for Standardization Working Group (ISO) TC31/SC3/WG19, where the dimension “0,33h” was judged wrong and constituting an unnecessary over constraint and to amend the inflation value to be used for the tyre conditioning when assessing the “flat tyre running mode” of “run flat tyres” and of “extended mobility tyres”.
Proposal to clarify the scope and application of the regulation.
Proposal to improve the Appendix 2 Annex 3 for assessing robustness against false reaction, to introduce new provisions for automatic deactivation of AEBS, and to improve the text in other instances.
Proposal to introduce provisions under a car-to-bicycle test scenario.
Proposal for alternative language regarding markings to avoid use of the term “moulded” which could be interpreted as a technical design restriction and to add a reference to “log-skidder” tyres.
90. AC.3 noted that no guidance was requested.