Proposal to amend document GRBP-83-32-Rev.1. Paragraph 1.2.9. amended to exclude special use Professional off-road tyres from scope. Paragraph 2.51. amended to read that the authority which has granted type approval may verify conformity control methods, with normal minimum frequency of verifications at least once every three years. Justification states special use tyres should be excluded as no limits will be established for them, and the three-year frequency aligns with Schedule 1 of the 1958 Agreement.

ETRTO comments on EC/JRC compromise proposal for Annex 4 tyre abrasion. ETRTO proposes an ALI range minimum of 0.5 as feasible and consistent with statistical distribution in MA results, rejecting the 0.7 range as unrealistic. For Generic Transfer Function gain, ETRTO recommends retaining a = 1.38 rather than the revised a = 1.45, to minimize rejection of good vehicle test results. ETRTO requests TFTA ToR amendment to confirm these conditions by February 2027 based on TA-45-9.

Proposal to amend document GRBP-83-32-Rev.1 to renumber Paragraph 6.1. as 6.1.1., renumber current Paragraph 6.1.1. as 6.1.2., introduce new paragraph 1.4. to Annex 3 Introduction, amend paragraph 2.8. with detailed abrasion index and level calculation equations, renumber items in Appendix 2, delete item 1.3. from Appendix 2, and amend item 1.3. in Appendix 6 to clarify transfer function applicability between circuit and drum test facilities.

Proposal to amend GRBP-83-32-Rev.1 to ensure robust tyre abrasion measurements regardless of test method used. Amendments modify paragraph 6.1 to require test facilities demonstrate equivalence per Annex 4 procedure; insert paragraphs 12.8 and 12.9 deeming inter-facility campaign participants equivalent for C₁ tyres and allowing pre-regulation test data through 1 July 2028; insert Annex 3 paragraph 1.4 requiring inter-facility equivalence assessment; amend Annex 3 paragraph 2.8 with abrasion calculation equations including transfer function coefficient; insert test report items 1.1–1.4 in Appendices 2 and 6; and insert new Annex 4 establishing equivalence demonstration procedure for vehicle and indoor drum test facilities.

JATMA submitted this position on the draft UN Regulation for tyre abrasion at GRBP-83-54. JATMA requests adoption of the indoor drum test method under conditions equivalent to the vehicle test method for type approval. JATMA proposes that the Generic transfer function coefficient should be 1.14, calculated excluding tyre code 127 which exhibits significant variation. JATMA also proposes that the abrasion index range for tyres used in the Annex 4 procedure should be set between 0.4 and 0.5, and that no restrictions should be imposed on baseline test facilities when applying the Specific Transfer Function.

This status report documents the Tyre Abrasion Task Force’s progress toward finalizing a draft UN Regulation on tyre abrasion for C1 tyres, as presented to GRBP 83 Part II. The task force pursued three workstreams: data analysis to reduce method uncertainty and inversion risk, editorial improvements to increase clarity of the draft regulation, and development of a method equivalence solution. GRBP 83 Part I achieved consensus on limit values and introductory dates but could not reach consensus on equivalence procedures between convoy and drum methods. Six informal documents (GRBP-83-32-Rev.1, GRBP-83-48-Rev.1, GRBP-83-49, GRBP-83-50-Rev.1, GRBP-83-53, and GRBP-83-55) addressing equivalence methodology, drum specifications, and code of practice frequency were submitted for potential adoption at the extraordinary GRBP 83 Part II session.

Proposal to delete Table of contents, Annex 10 and all its appendices, amend para. 1.1. to clarify application to new pneumatic tyres of classes C1, C2 and C3 in new state regarding sound emissions and rolling resistance and in new and worn state regarding wet adhesion, delete para. 1.3., amend para. 2.18. to specify reference tyres F2872-25, F2871-25, F3678-25 and F3677-23, delete para. 2.21., delete para. 3.1.1.1., amend para. 3.2.1. to describe major features and their effects on tyre performance, delete paras. 5.7. to 5.10., delete Annex 1 items 8.6. and 8.6.1., amend Annex 5 part (b) para. 1.1.1. to establish surface friction values by trailer or vehicle method according to tyre class and SRTT, amend Annex 5 part (b) para. 1.1.1.1. regarding coefficient of variation and peak braking force coefficient, and delete Annex 10. Document based on GRBP/2025/28, GRBP-82-27, GRBP/2026/6, GRBP-83-20/Rev.2 and GRBP-83-48/Rev.1.

The proposal adds Annex 5 on special provisions for testing vehicles equipped with an Automated Driving System (ADS) and adds definitions for ADS, Dynamic Driving Task, Category X and Y vehicles, logical signal, and Vehicle Master Control Switch. Amendments modify run-flat warning system requirements, braking performance tests, and tyre detection procedures to accommodate ADS-equipped vehicles.

Proposal to amend paragraph 1 (Scope) to clarify that the Regulation applies to new pneumatic tyres designed primarily for vehicles of category L₁, and to specify that approvals shall not be granted to tyre types designed exclusively for off-road use marked “NHS”, for competitions, or for bicycle rims according to ISO 5775-2:2021.

Proposal to amend paragraph 1.1. to specify that UN R106 applies to new pneumatic tyres designed primarily for agricultural and forestry vehicles in categories T, R and S; amend paragraph 1.1. footnotes to include definitions; and amend paragraph 3.1.5.3. to address marking requirements for implement tyres for mixed applications of speed category symbol D or E where service descriptions for trailer and traction applications are equal.