Proposal to clarify the definitions of type with regard to manufacturer, trade names and marks.

Submission by the Working Party “Brussels 1952” (GTB) to clearly define the conditions under which voltage control gear may be used in conjunction with filament light sources.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to amend the provisions concerning the heat test requirements for conformity of production.

Proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks.

Recommended corrections to the proposal to clarify the definition of “type” with regard to manufacturer, trade names and marks as used in Regulations Nos. 4, 6, 7, 19, 23, 38, 45, 50, 77, 87, 91,98 ,104, 112, 113, 119 and 123.

Text prepared by the International Automotive Lighting and Light Signalling Expert Group (GTB) to clarify the definition of “type”, with regard to manufacturer, trade names and marks and to introduce editorial improvements to the requirements for markings.

Although documents GRE/2013/45 and GRE-70-02 were adopted by GRE at its last (70th) session, this proposal consolidates the amendments and offers editorial improvements to the provisions concerning markings in Regulations Nos. 19, 23, 38, 65 and 119. These editorial improvements aim to clarify that the devices, and not only the samples, shall bear the trade name or mark and align the requirements with the other correctly worded regulations to avoid misunderstanding.

Proposal to simplify measuring the objective luminous flux of light emitting diode (LED) module(s) and to replace the current variety of test mixtures used to simulate dirt during the testing of lamps with a single uniform mixture. In addition, the proposal would replace the term “beech wood” with the phrase “produced from beech wood” to improve clarity.

Correction of errors found in the references to “left-hand traffic” and “right-hand traffic” in the text and associated diagrams of Annex 2 of the regulation.

Updated paper on the grouping of lighting regulations under one of three new regulations as follows:
Light Signaling Devices incorporating Regulations 4, 6, 7, 23, 38, 50, 77, 87, and 91
Forward Lighting Devices incorporating Regulations 19, 98, 112, [ 113 ], 119, and 123
Retro-Reflective Devices incorporating Regulations 3, 27, 69, 70, and 104

Proposal to amend the formula for the dirt mixture used in testing to address an error introduced by Supplement 9 to the 01 series of amendments to UN R45 where the specified quantity of “2 ± 1 parts by weight” of surfactant results in invalid testing. The correct specification should be “2 ± 1 drops” of surfactant. While GTB notes that the specification should eventually be incorporated differently under the pending simplification of lighting regulations, the organization strongly urges amending UN R45 as quickly as possible.

This collective amendment on the stability of photometric performance during the heat test, with particular reference to the movement of the cut-off line, clarifies the test cycle and also aligns the requirements of Regulations Nos. 19, 98, 112, 113 and 123. In addition to resolving problems of interpretation presented by the current text, this collective amendment will assist the Informal Working Group “Simplification of Lighting and Light-Signalling Regulations” in drafting the new simplified Regulations which is underway.

Supplement 3 to the 01 series of amendments to UN R 98, 112, and 123 deleted the measurement point HV from the photometric requirement table. The HV measurement point, however, remains a requirement for checking photometric stability. This proposal removes the HV measurement point from the photometric stability requirements for the passing beam. The HV measurement point remains a valid for the driving beam.

This collective amendment extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123 (as presented in the previous session document GRE-75-14). The proposal would allow for the use of regulated replaceable LED light sources according to Regulation No. 128 in all applications where the use of LED modules is already permitted.

Proposal to update document GRE/2016/34. At the 73rd GRE session, France proposed to delete a design restrictive requirement (GRE/2015/22 and GRE-73-26). This proposal received comments from Germany and the Netherlands. Poland suggested a different approach on this issue (GRE-73-21). The Chair invited France, Germany, Netherlands, Poland, CLEPA and IEC to prepare a revised proposal for the next session. Based upon the approach proposed in GRE/2015/22 and GRE-73-26, GTB has investigated the specification of minimum levels of flux projected in critical zones of the passing beam distribution. This approach offers a technology-neutral performance based requirement. The result of the GTB study is to propose minimum projected flux requirements in two zones:
a) 15°D-1°U/30°L-30°R to ensure overall adequate illumination of the road and
b) 3.5°D-1°U/30°L-30°R to ensure sufficient range.

The collective amendment presented in GRE/2016/34 extends the usage of LED light sources of UN R128 to front lighting Regulations Nos. 19, 98, 112, 113 and 123. The introduction of LED light source categories under UN R128 for forward lighting applications (front fog, low beam, high beam,
AFS) is planned for 2017. This presentation explains the plans, timeline, and dependencies GTB proposes to address through the collective amendment, especially within the context of the simplification of lighting regulations program.

Discussion paper concerning modifications to the draft proposal for a new UN Regulation on road illumination devices in order to achieve the aims of GRE/2016/34 which proposed amendments to Regulations 19, 98, 112, 113 and 123.