Editorial amendment to align the definition of “special tyre” with the proposal for the snow tyre definition in paragraph 2.33.

Proposal to supersede GRBP/2023/10 with a more flexible approach appropriate for covering the operations of small retreaders.

Proposal to replace GRBP/2023/11 with a revised proposal to address the following:

1. “Special use” tyres with nominal rim diameters larger than those listed in the present table (rim diameters up to 42, section widths up to 750 mm and overall diameters over 2 meters) and with speed symbols F and above have been announced in the European market as original equipment of N3G “special purpose vehicles” (i.e., special high speed self-propelled vehicles for agricultural and forestry use, like wood choppers).

2. Existing multi-purpose tyres (MPT) (classified as “special use tyres” as per paragraphs 2.5.3. and 3.1.13.), already type approved since years, have a tread pattern with lugs or cleats in addition to those with blocks, as evidenced by the attached slide showing some examples. It is proposed to amend paragraph 6.3.1. by clarifying that lugs and cleats are possible shapes of the mentioned blocks.

3. Testing tyres with very large overall diameters, sometimes over 2 m, on a test drum with a diameter of 1.70 m ± 1 % would be unpracticable. For practical reasons most of those tyres are regularly tested on drums with a diameter of 3 m or even larger. The proposal carries equivalence provisions from UN R106 to justify the equivalence of the test method as required by Annex 7 in point 4 “Equivalent test methods" and clarifies based on UN R117 the formula already used indirectly.

4. Some commercial vehicles are often used in the market at a reduced speed of 70 km/h with a load-capacity of the tyres increased as per load/speed combination defined in the table of Annex 8. The proposal would allow use of the speed category symbol E (but restrict it to “additional service description”) to provide this information.

5. Considering that 32 km/h is already a floor value for the test-drum speed for diagonal tyres, ETRTO proposes not to apply to E speed category symbol tyres the linear decrease of the test-drum speed in function of the decrease of the speed category symbol by keeping, for safety reasons, the same test-drum speed as for F speed category symbol tyres, i.e., 32 km/h).

6. In the case of additional service descriptions mentioned in paragraph 6.2.5.1., it is proposed not to perform the additional load/speed test because the load-capacity approximates with a negligeable difference the reduction or the increase in percentage of the nominal load/speed combination applicable to the nominal speed category symbol (see Annex 8). An example of the actual differences (in percentage and in absolute value) is provided.

7. Type approval applications for radial tyres with load capacity index greater or equal to 122 and without the additional marking “LT”, or “C” have been done in the past for the speed category symbol N for which the load/speed endurance test procedure is not described in Annex 7, Appendix 1. To type approve such tyres the test speed was separately defined by the different involved Type Approval Authorities. In order to harmonize the test procedure to be used for the type approval of such tyres, it is proposed to amend the Annex 7, Appendix 1 by introducing testing conditions in line with the rule applied for defining the test speed of radial tyres with load capacity index greater or equal to 122 (i.e. starting from 32 km/h set for F speed category symbol, the test speed is increased by 8 km/h respect to the one set for the previous speed category symbol).

8. The definition of “snow tyre” is amended to clarify that “snow tyres” are not only suitable for the use in snow conditions but also on mud and by replacing the term “maintain vehicle motion” (i.e. keeping the vehicle speed and direction of movement constant) by a more general concept of “controlling vehicle motion” (i.e. also being able to change the vehicle speed and direction of movement as intended).

9. It is proposed to explicitly allow other technical measurement solutions of the tyre overall width by removing the words “by caliper” which fix a technical limitation. The removal of this technical limitation would be advisable following the principle of not stopping the technical innovations.

Proposal to introduce measures to reduce variability in noise measurement.

Information concerning discussions on the proposals to extend the scope to ‘E’ speed symbol.

Small group (France, Netherlands, ETRTO, BIPAVER) proposal to restructure retreaded tyre requirements and regulations.

Proposal from a small group effort for uniform provisions concerning the approval of pre-cured tread materials which are used for producing retreaded tyres or the approval of retreaded tyres produced by using mould cure process with regard to their snow performance.

Small group proposal to split retreaded tyre requirements into a new UN Regulation.

Proposal to introduce a new temperature correction formula for the rolling sound emissions of tyres of classes C1 and C2, to remove the content of the now obsolete Annex 4 as well as all its references, to update references to standards, and to make editorial improvements for clarity and consistency across tyre regulations.

Proposal to reduce noise measurement variability, completing the amendment proposal adopted at the seventy-eighth session of the Working Party on Noise and Tyres (informal document GRBP-78-05 replacing ECE/TRANS/WP.29/GRBP/2023/19).

Proposal to complete the amendment proposal adopted at the 78th GRBP session (informal document GRBP-78-05 replacing ECE/TRANS/WP.29/GRBP/2023/19).

Proposal to improve the reproducibility of the snow grip test method by replacing the current reference tyres C3 SRTTs 19.5 and 22.5 with the new reference tyres C3 SRTTs 19.5 and 22.5 siped.

Proposal to improve the reproducibility of the snow grip test method by replacing the current reference tyres C3 SRTTs 19.5 and 22.5 with the new reference tyres C3 SRTTs 19.5 and 22.5 siped.

Proposal for editorial corrections.

Proposal for editorial improvements and updates to ISO and ASTM standards references and to align with Supplement 2 to the 04 series of amendments, including a new temperature correction formula for the rolling sound emissions of tyres of classes C1 and C2 and to remove the content of the now obsolete Annex 4 as well as all its references.