ETRTO proposal for the replacement of the current Standard Reference Test Tyre as it is being phased out as production will stop mid of 2020. Snow performance test in R117 currently requires SRTT14 as a reference tyre. SRTT14 needs to be replaced and test procedure amended.

ETRTO report on the study on the Dimensional Requirements for tyres with radial or run flat structure after having performed the load speed endurance test. ETRTO proposes to amend the UN Regulations No 30, 54 [and 75] by removing the requirements for tyres with radial and run flat structure.

ETRTO proposal for amending tyre marking method by the removal of the use of wording “moulded” in the marking clause as this is only one of the various technical solutions currently available.

The text submitted by the experts from the European Tyre and Rim Technical Organisation (ETRTO) to amend the Japanese proposal for a Supplement to the 02 series of amendments (ECE/TRANS/WP.29/GRBP/2020/6)

Changes to the proposal to align definitions across tyre regulations and align the regulations with technological progress, correct an editorial error, and clarify that the ply rating is not applicable to T-type temporary use tyres.

Proposal to include requirements for wet grip of tyres of classes C2 and C3 in worn state to the scope of the working group activities.

Overview of UTAC CERAM testing designed to consider the impact of additional tightening of tyre performance limits on the balance
between legal requirements (rolling resistance, wet grip and rolling sound emission) and other performance aspects not subject to legal requirements.

Comments on the proposals prepared by BIPAVER, France and Netherland to align the test procedures for retreaded tyres with the latest amendments to R30, R54 and R117.

This proposal aligns with the “Alpine symbol” location that is not restricted to the lower area of the tyre as prescribed in UN Regulation No. 117, especially considering the larger dimensions of the “Snow Grip Marking for Studded Tyres"

Corrections and alignment to document ECE/TRANS/WP.29/GRBP/2021/15

Proposal to avoid placing requirements in the Definitions section and to facilitate the text by making use of the definition of “service description” that was introduced by Supplement 24.

Proposals for editorial corrections to the provisions for type approval of special use tyres that fulfil the requirements for snow performance

Proposal for editorial corrections

Proposal introduces provisions to allow the type approval of special use tyres that fulfil the requirements for snow performance as laid out in Annex 7. The respective marking related to the “Alpine” symbol has been considered for those tyres complying with these requirements.

Proposal introduces provisions to allow the type approval of special use tyres that fulfil the requirements for snow performance as laid out in Annex 7. The respective marking related to the “Alpine” symbol has been considered for those tyres complying with these requirements

Re-introduces the definition of traction tyre as this can be still used between the entry into force date of the 04 series of amendments and 7 July 2024 .

Editorial corrections and amends the transitional provisions

Proposes the amendment to the transitional provisions aligning with other proposals

Updates the reference to latest version of ISO 10844:2021

Editorial amendment to align the definition of “special tyre” with the proposal for the snow tyre definition in paragraph 2.33.

Proposal to supersede GRBP/2023/10 with a more flexible approach appropriate for covering the operations of small retreaders.

Proposal to replace GRBP/2023/11 with a revised proposal to address the following:

1. “Special use” tyres with nominal rim diameters larger than those listed in the present table (rim diameters up to 42, section widths up to 750 mm and overall diameters over 2 meters) and with speed symbols F and above have been announced in the European market as original equipment of N3G “special purpose vehicles” (i.e., special high speed self-propelled vehicles for agricultural and forestry use, like wood choppers).

2. Existing multi-purpose tyres (MPT) (classified as “special use tyres” as per paragraphs 2.5.3. and 3.1.13.), already type approved since years, have a tread pattern with lugs or cleats in addition to those with blocks, as evidenced by the attached slide showing some examples. It is proposed to amend paragraph 6.3.1. by clarifying that lugs and cleats are possible shapes of the mentioned blocks.

3. Testing tyres with very large overall diameters, sometimes over 2 m, on a test drum with a diameter of 1.70 m ± 1 % would be unpracticable. For practical reasons most of those tyres are regularly tested on drums with a diameter of 3 m or even larger. The proposal carries equivalence provisions from UN R106 to justify the equivalence of the test method as required by Annex 7 in point 4 “Equivalent test methods" and clarifies based on UN R117 the formula already used indirectly.

4. Some commercial vehicles are often used in the market at a reduced speed of 70 km/h with a load-capacity of the tyres increased as per load/speed combination defined in the table of Annex 8. The proposal would allow use of the speed category symbol E (but restrict it to “additional service description”) to provide this information.

5. Considering that 32 km/h is already a floor value for the test-drum speed for diagonal tyres, ETRTO proposes not to apply to E speed category symbol tyres the linear decrease of the test-drum speed in function of the decrease of the speed category symbol by keeping, for safety reasons, the same test-drum speed as for F speed category symbol tyres, i.e., 32 km/h).

6. In the case of additional service descriptions mentioned in paragraph 6.2.5.1., it is proposed not to perform the additional load/speed test because the load-capacity approximates with a negligeable difference the reduction or the increase in percentage of the nominal load/speed combination applicable to the nominal speed category symbol (see Annex 8). An example of the actual differences (in percentage and in absolute value) is provided.

7. Type approval applications for radial tyres with load capacity index greater or equal to 122 and without the additional marking “LT”, or “C” have been done in the past for the speed category symbol N for which the load/speed endurance test procedure is not described in Annex 7, Appendix 1. To type approve such tyres the test speed was separately defined by the different involved Type Approval Authorities. In order to harmonize the test procedure to be used for the type approval of such tyres, it is proposed to amend the Annex 7, Appendix 1 by introducing testing conditions in line with the rule applied for defining the test speed of radial tyres with load capacity index greater or equal to 122 (i.e. starting from 32 km/h set for F speed category symbol, the test speed is increased by 8 km/h respect to the one set for the previous speed category symbol).

8. The definition of “snow tyre” is amended to clarify that “snow tyres” are not only suitable for the use in snow conditions but also on mud and by replacing the term “maintain vehicle motion” (i.e. keeping the vehicle speed and direction of movement constant) by a more general concept of “controlling vehicle motion” (i.e. also being able to change the vehicle speed and direction of movement as intended).

9. It is proposed to explicitly allow other technical measurement solutions of the tyre overall width by removing the words “by caliper” which fix a technical limitation. The removal of this technical limitation would be advisable following the principle of not stopping the technical innovations.

Information concerning discussions on the proposals to extend the scope to ‘E’ speed symbol.

Small group (France, Netherlands, ETRTO, BIPAVER) proposal to restructure retreaded tyre requirements and regulations.

Small group proposal to split retreaded tyre requirements into a new UN Regulation.

Proposal from a small group effort for uniform provisions concerning the approval of pre-cured tread materials which are used for producing retreaded tyres or the approval of retreaded tyres produced by using mould cure process with regard to their snow performance.

Proposal to replace document ECE/TRANS/WP.29/GRBP/2024/06