Proposal to update Annex 4, Part A, Section I (List of requirements for U-IWVTA) to align with recent changes to UN R110, 134, 135, 137, and 138.

ANEC calls for support for proposal to improve UN Regulation No. 44 on Child Restraint Systems to ensure the highest protection practicable for children travelling by car.

The Russian Approval Authority had concluded that the product brand “Braxx”, type “Smart Kid Belt” approved according to UN Regulation No. 44, approval No. E20 44R-04 4013 granted by Poland on 11 July 2017, cannot be considered as a child restraint system.

Proposal to transpose the provisions on minimum number of anchorage points and location of lower anchorages from Consolidated Resolution on the Construction of Vehicles (R.E.3).

Proposal to align the 08 series with previous series of amendments with regard to approval authority notification of modifications that affect technical performance and/or documentation.

Proposal to exempt “sensors, cameras, radar devices, etc.” components of approved driver assist systems from the Annex 3 prohibition against damage provided the basic braking and steering performance remains intact.

Proposal to prohibit new type approvals under UN R44 from [1 September 2020] via the introduction of new transitional provisions. The purpose is to ensure that further child restraint system approvals are made under the UN R129. The proposal also further clarifies the text to explicitly prohibit non-integral belt guides and other seating devices offered separately from the child restraint system.

Proposal to update a reference with the new European Committee for Standardization (CEN) published EN 71-3:2019 on 10 April 2019 and to delete a cut-and-paste error in Annex 6, Appendix 2 taken from UN R44 referring to ECRS as in the “restricted” category which does not exist in UN R129.

Proposal to update a reference with the new European Committee for Standardization (CEN) published EN 71-3:2019 on 10 April 2019, to delete a cut-and-paste error in Annex 6, Appendix 2 taken from UN R44 referring to ECRS as in the “restricted” category which does not exist in UN R129, and to reconcile and consolidate various references to tolerances for the internal geometry assessment.

Proposal to clarify the requirements for the type approval category of booster seats over 135 cm, to update a reference with the new European Committee for Standardization (CEN) published EN 71-3:2019 on 10 April 2019, to delete a cut-and-paste error in Annex 6, Appendix 2 taken from UN R44 referring to ECRS as in the “restricted” category which does not exist in UN R129, and to reconcile and consolidate various references to tolerances for the internal geometry assessment.

Proposal from a drafting task force to:

• Align UN Regulations with the provisions of the revised General Safety Regulation of the European Union, thus, expand the scope of the UN Regulation No. 137,
• Provide appropriate transitional provisions, and
• Make minor adaptations and clarifications to the existing requirements.

Consolidated update of UN R22 from the informal working group on protective helmets, including:

• Reference headforms (shape, dimensions)
• Oblique impact test method of measuring rotational acceleration
• Product of the spectral distribution of radiation of the signal light and standard illuminant D65
• High speed particle test for visors, and
• Test for photochromic, liquid crystal visors.

Proposal to remove restrictions on the scope of the Regulation to M1 and N1 vehicles, to provide appropriate transitional provisions and to make minor adaptations and clarifications to the existing requirements.

Proposal to introduce provisions to avoid the burden of a new road load determination (e.g., NEDC) in cases where the road load has already been performed under GTR 15 (WLTP), to amend provisions on On-Board Diagnostics (OBD), road load coefficient determination, mono fuel gas vehicles pursuant to WLTP, and to introduce definitions for the terms “permanent” and “Limp-home routines”, and to clarify “permanent emission default modes”.

Proposal to introduce provisions to avoid the burden of a new road load determination (e.g., NEDC) in cases where the road load has already been performed under GTR 15 (WLTP), to amend provisions on On-Board Diagnostics (OBD), road load coefficient determination, mono fuel gas vehicles pursuant to WLTP, and to introduce definitions for the terms “permanent” and “Limp-home routines”, and to clarify “permanent emission default modes”.

Proposal to adapt the provisions in UN R101 to allow the usage of road load powers which have been derived from those determined in accordance with UN GTR No. 15 (WLTP).

Proposal to harmonise the requirements of UN R78 with the latest amendments to UN GTR No. 3 adopted by GRVA at its fourth session. Paragraph 5.1.18 aims to clarify with an explicit article that the rider is duly informed when activating a riding mode that disables the ABS on the rear axle.

Proposal to resolve measurement concerns in the test requirements for ACSF of Category B1 and C by introducing provisions for tolerances, including:

1. inclusion of the position at which the lateral acceleration was measured and the position of the centre of gravity of the vehicle for better traceablility,
2. sampling rate of at least 100 Hz for dynamic testing,
3. specification of filters and cut-off frequency for determination of lateral acceleration,
4. option to measure “overriding force” torque via an internal sensor or an external device (e.g., steering robot).

Proposal to stipulate that “Automatic deactivation by the system of the direction indicator is required only if the lane change manoeuvre is initiated automatically, and if the direction indicator control is not fully engaged (latched position) during the lane change manoeuvre.” The proposal also would modify the high-speed test to end once the system has given an optical “hands-off” warning since the entire warning cascade is checked during the low-speed test. For M₂ and M₃ vehicles, the amendment allows a corrective steering function to use haptic signals as an alternative to acoustic signals for these categories of vehicles that are equipped with Lane Departure Warning System compliant with UN R130. This change would specify that the haptic warning may not be given solely via the steering wheel (e.g., provided in the driver’s seat).

Proposal to allow for the use of the maximum operable steering wheel angle of a steering system’s design in cases where the normalized angle as calculated under the regulation cannot meet the fixed values of the regulation (i.e., between 270 and 300 degrees). The intention is to enable approval of eventual systems (e.g., steer-by-wire) that may use low steering gear ratios.

Proposal to improve the robustness of the test procedure, including number of test runs and assessment of failures.

Proposal to introduce provisions for stationary noise measurements on a single-sided dual exhaust system, minimize proliferation of approval numbers from models with differences in vehicle exhaust and silencing systems, and correct an omission regarding the compensating resevoir fill time thereby aligning UN R41 with the other noise UN Regulations Nos. 9, 51 and 63.

Proposal to clarify that it is not necessary to require an ISO 10844 asphalt track surface in cases where the vehicle is at a standstill provided that the surface is dense and without substantial absorption characteristics.

Proposal to align definitions across tyre regulations and align the regulations with technological progress, correct an editorial error, and clarify that the ply rating is not applicable to T-type temporary use tyres.

Proposal to align the provisions for retreaded tyres to be tested and marked with the three-peak-mountain snow-flake (3PMSF) symbol with the related amendment proposals to UN R117.

Proposal to align the provisions for retreaded tyres marked using the three-peak-mountain snow-flake (3PMSF) symbol with amendments to UN R117 and to restore the remainder of a sentence that was unintentionally deleted in paragraph 3.2.1. during a previous amendment procedure.

Proposal to adapt the rolling-sound measurement procedures to accommodate special C2 tyres presenting a section width wider than 200 mm, aspect ratio lower than 55, rim diameter code lower than 15 and without any dual fitting indication (i.e. the front size 175/75R15 LT and the rear size 235/50R14 LT or the front size 175/75R15 LT and the rear size 265/50R14 LT).

Proposal for a new UN Regulation for the type approval of M1 vehicles with a total permissible mass not exceeding 3,500 kg and of N1 with regard to fuel integrity and safety of high voltage systems in case of a rear-end collision. This proposal aligns rear impact (UN R34) and electric vehicle safety (UN R100) requirements with the new EU General Safety Regulation and with GTR 20 on electric vehicle safety.

Proposal for a new UN Regulation on uniform provisions concerning the approval of light duty passenger and commercial vehicles with regards to criteria emissions, emissions of carbon dioxide and fuel consumption and/or the measurement of electric energy consumption and electric range.

Proposal for a new 01 series of amendments to a new UN Regulation on uniform provisions concerning the approval of light duty passenger and commercial vehicles with regards to criteria emissions, emissions of carbon dioxide and fuel consumption and/or the measurement of electric energy consumption and electric range.

Proposal for a new UN Regulation on uniform provisions concerning the approval of vehicles with regards to cyber security and cyber security management system.

Proposal for a new UN Regulation on uniform provisions concerning the approval of vehicles with regards to software update and software updates management system.

Proposal for a new UN Regulation on uniform provisions concerning the approval of vehicles with regard to Automated Lane Keeping Systems designed to operate on highways at speeds up to 60 km/h.

Proposal to introduce the use of software identification numbers (RXSWIN) in UN Regulations.

Proposal to amend requirements for front underrun protection devices to address aerodynamic body configurations.

Proposal to specify a head restraint height between 720 mm and 830 mm including a new method for measuring the effective height of head restraints, use of the Biofidelic Rear Impact Device (BioRID II) test dummy, and to improve the overall text. This proposal also eliminates the backset measurement test procedure using the HRMD method.

Proposal for Amendment 3 to the United Nations Global Technical Regulation No. 19 to introduce the evaporative emission test procedure for the Worldwide harmonized Light vehicles Test Procedure (WLTP EVAP).

Request to maintain in the Compendium of Candidates Listing Number 1 – Heavy-Duty Engine and Vehicle Standard and Highway Diesel Fuel Sulfur Control; Requirements; Final Rule.

Request to maintain in the Compendium of Candidates Listing Number 2 – Tier 2 Motor Vehicle Emissions Standards and Gasoline Sulfur Control Requirements; Final Rule.

Request to maintain in the Compendium of Candidates Listing Number 3 – Control of Emissions of Air Pollution from Non-road Diesel Engines and Fuel; Final Rule.

Proposal to correct errors and clarify provisions in the draft UN Regulation on WLTP.

Proposal to correct errors and clarify provisions of the draft 01 series of amendments to the draft UN Regulation on WLTP.

Proposal for provisions regarding the extension, expiration, or withdrawal of a cybersecurity approval.

Request for authorization to add a new mandate under the informal working group on Electric Vehicles and the Environment (EVE) to develop a new UN GTR on the topic of in-vehicle battery performance and durability.

Proposal agreed by interested Contracting Parties to resolve concerns regarding “peer review” of cybersecurity type approvals.

Proposal to improve the robustness of the test procedure, including number of test runs and analysis of failures.

Request to develop an amendment to the GTR 8 testing provisions to accommodate the latest innovations for steering systems which have significantly low steering gear ratio (i.e. quick steering characteristics).

Addendum to update the agenda with notations for additional formal documents submitted for the session.